sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. 3-Drawer Chest Pogo Collection | Model 414434 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 414434 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35GA CABINET RIGHT - 3 10A SLIDE CAM - 6 1G 35GB CABINET LEFT - 3 12E TACK GLIDE - 4 SAFETY BRACKET - 1 35GC DRAWER RIGHT - 3 1F HIDDEN CAM - 10 4G METAL BRACKET - 5 2F 59K KNOB - 6 35GD DRAWER LEFT - 3 CAM DOWEL - 10 5L 8M GLUE - 1 WARNING LABEL - 1 ! 21M CARD HOLDER - 1 15F WOOD DOWEL - 4 WARNING Serious or fatal crushing injuries can occur from furniture tip-over.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push ten HIDDEN CAMS (1F) into the ENDS (A2 and B2), BOTTOM (D), and BACKS (E). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 2F (10 used) This is a tracking label. Please do not remove.
Step 2 å Fasten the CABINET RIGHTS (35GA) and CABINET LEFTS (35GB) to the ENDS (A2 and B2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. Roller end 1 2 3 1 2 1 3 2 3 3 2 3 1 2 3 A2 S H urf ID a D ce E w N i C th A M S 1 2 1 Flat edge B2 S H urf ID a D ce E w N i C th A M S Roller end 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Page 6 414434 www.sauder.
Step 3 å Fasten the BOTTOM (D) to the RIGHT END (A2). Tighten two HIDDEN CAMS. A2 Sur withface HID CA DEN MS Flat edge This hole must be here. D ith e w MS c a f A Sur EN C D HID Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 4 å Fasten both BACKS (E) to the BOTTOM (D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Edge with CAM DOWELS S w urf ho ith ac le ou e s t E S w urf ho ith ac le ou e s t E D 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Page 8 414434 www.sauder.
Step 5 å First, fill the four holes in the FRONT PANEL (F2) 1/4 to 1/2 full with GLUE (8M). Then, insert a WOOD DOWEL (15F) into each hole. Wipe away the excess GLUE. å Fill the two holes in the RIGHT END (A2) 1/4 to 1/2 full with GLUE. Then, insert the WOOD DOWELS in the FRONT PANEL (F2) into these holes. Wipe away the excess GLUE. å Next, fill the two holes in the LEFT END (B2) 1/4 to 1/2 full with GLUE (8M). Then, insert the WOOD DOWELS (15F) in the FRONT PANEL (F2) into the holes in the LEFT END.
Step 6 å Fasten the TOP (C) to the ENDS (A2 and B2). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge The two HIDDEN CAMS in the BACKS (E) will be tightened in Step 12. C A2 E B2 Page 10 414434 www.sauder.
Step 7 å Fasten the TOP MOLDING (M29) to the TOP (C). Use three BROWN 1-1/2" FLAT HEAD SCREWS (14S). å NOTE: Do not overtighten the SCREWS into the TOP. Don't worry. It isn't Rome. This can be built in a day. 14S BROWN 1-1/2" FLAT HEAD SCREW (3 used in this step) Curved edge M29 C www.sauder.
Step 8 å Fasten two METAL BRACKETS (4G) to the RAIL (R) as shown in the upper diagram below. Use two BROWN 7/16" LARGE HEAD SCREWS (6S). å NOTE: Be sure the BRACKETS are even with the ends of the RAIL. å Fasten the RAIL (R) to the ENDS (A2 and B2) as shown in the lower diagram. Use two BROWN 7/16" LARGE HEAD SCREWS (6S). 4G Surface with more holes 4G 6S BROWN 7/16" LARGE HEAD SCREW (4 used for the METAL BRACKETS) R A2 R B2 Page 12 414434 www.sauder.
Step 9 å Fasten the SKIRT (G) to the ENDS (A2 and B2) and BOTTOM (D). Use three METAL BRACKETS (4G) and six BROWN 7/16" LARGE HEAD SCREWS (6S). å With your hammer, gently tap four TACK GLIDES (12E) into the bottom edges of the ENDS (A2 and B2). 6S BROWN 7/16" LARGE HEAD SCREW (6 used in this step) A2 Curved edge G 4G B2 D 12E 4G 4G 12E www.sauder.
Step 10 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. Un fi su nish rfa ed ce D22 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. D704 D22 H H D23 D23 Groove Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. å Insert the LARGE DRAWER SIDES (D22 and D23) at an angle into the slot at each end of the LARGE DRAWER FRONT (H).
Step 11 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D22 and D23). å å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the DRAWER RIGHT (35GC) and DRAWER LEFT (35GD) to the DRAWER SIDES (D22 and D23). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Fasten two KNOBS (59K) to the LARGE DRAWER FRONT (H). Use two BLACK 1-1/8" PAN HEAD SCREWS (9S). Repeat this step for the other large drawer and the small drawer.
Step 12 å å Carefully stand your unit upright. å Fasten the CARD HOLDER (21M) to the RAIL (R). Use two SILVER 3/8" MACHINE SCREWS (97S). å Separate the CARDS on the CARD SHEET (40M) and insert one into the CARD HOLDER. å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BROWN 7/16" LARGE HEAD SCREW (6S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. Fasten the BACKS (E) to the TOP (C). Tighten two HIDDEN CAMS.
Step 13 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å Apply the WARNING LABEL (5L) to the upper LEFT DRAWER SIDE (D17). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 14 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 414434 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Attention: Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer dix EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2), le DESSOUS (D) et les ARRIÈRES (E).
ÉTAPE 9 ÉTAPE 12 Fixer la PLINTHE (G) aux EXTRÉMITÉS (A2 et B2) et au DESSOUS (D). Utiliser trois CONSOLES EN MÉTAL (4G) et six VIS TÊTE LARGE 11 mm MARRON (6S). Relever, avec précaution, l'élément dans sa position verticale. À l'aide d'un marteau, enfoncer quatre PATINS (12E) dans les chants inférieurs des EXTRÉMITÉS (A2 et B2). Fixer la PORTE-ÉTIQUETTE (21M) à la TRAVERSE (R). Utiliser deux VIS À MÉTAUX 10 mm ARGENT (97S).
Modelo 414434 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Precaución: Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje diez EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A2 y B2), del FONDO (D) y de los DORSOS (E).
PASO 9 PASO 12 Fije el FALDÓN (G) a los EXTREMOS (A2 y B2) y al FONDO (D). Utilice tres SOPORTES DE METAL (4G) y seis TORNILLOS MARRONES DE CABEZA GRANDE de 11 mm (6S). Cuidadosamente ponga la unidad en posición vertical. Con un martillo, suavemente introduzca golpeando cuatro TACHUELAS DESLIZANTES (12E) en los bordes de la parte inferior de los EXTREMOS (A2 y B2). Fije el PORTA ETIQUETAS (21M) al RIEL (R). Utilice dos TORNILLOS PLATEADOS PARA METAL de 10 mm (97S). PASO 10 1.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
