413329 Wardrobe/Storage Cabinet Beginnings Collection PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-14 Français ...............Pages 15-17 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ASSEMBLY TOOLS REQUIRED Part Identification .......................3 No. 2 Phillips Screwdriver Hardware Identification .............4 Tip Shown Actual Size Assembly Steps .................... 5-14 Français .............................. 15-17 Hammer Espanol............................... 18-20 Safety ................................. 21-22 Straight Edge Screwdriver Warranty ...................................23 Page 2 www.sauder.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. A RIGHT END 1 D TOP 1 G DOOR 2 B LEFT END 1 E SHELF/BOTTOM 2 H ADJUSTABLE SHELF 2 C UPRIGHT 1 F BACK 1 I BASE 1 D F E A H C H B G G E I 413329 www.sauder.
HARDWARE IDENTIFICATION J K ROD HANGER - 2 ROD - 1 M HINGE - 6 L PULL - 2 N SAFETY BRACKET - 1 P FELT DISC CARD - 1 Q SCREW COVER - 12 O METAL BRACKET - 5 R METAL PIN - 8 S RUBBER SLEEVE - 8 T BLACK 1-7/8" FLAT HEAD SCREW - 17 U SILVER 3/4" MACHINE SCREW - 4 V BLACK 9/16" LARGE HEAD SCREW - 1 W SILVER 1/2" FLAT HEAD SCREW - 2 X BROWN 7/16" LARGE HEAD SCREW - 34 Y NAIL - 59 Screws are shown actual size. You may receive extra hardware with your unit. Page 4 www.sauder.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 Finished edge Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. D Fin ish B ed E Un fini she d T BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Fasten the TOP (D) and SHELF/BOTTOM (E) to the LEFT END (B).
S p te 2 Finished edge B E C e ac les f r Suth ho wi Un E fini she d T BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Fasten the UPRIGHT (C) to the SHELF/BOTTOM (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (T). Fasten the other SHELF/BOTTOM (E) to the LEFT END (B) and UPRIGHT (C). Use four BLACK 1-7/8" FLAT HEAD SCREWS (T). Page 6 www.sauder.
S p te 3 W SILVER 1/2" FLAT HEAD SCREW (2 used in this step) K K Finished edge T BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Fasten the RIGHT END (A) to the TOP (D) and both SHELF/BOTTOMS (E). Use six BLACK 1-7/8" FLAT HEAD SCREWS (T). Fasten the ROD HANGERS (K) to the LEFT END (B) and UPRIGHT (C). Use two SILVER 1/2” FLAT HEAD SCREWS (W). 413329 www.sauder.
S p te 4 O X BROWN 7/16" LARGE HEAD SCREW (5 used in this step) I O (5 used) O Fasten five METAL BRACKETS (O) to the BASE (I). Use five BROWN 7/16" LARGE HEAD SCREWS (X). Page 8 www.sauder.
S p te 5 B I A E X BROWN 7/16" LARGE HEAD SCREW (5 used in this step) Fasten the BASE (I) to the ENDS (A and B) and SHELF/BOTTOM (E). Use five BROWN 7/16" LARGE HEAD SCREWS (X). 413329 www.sauder.
S Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. p te 6 1-1/2" 5" Draw these lines to nail on. 1/4" 14-3/8" F B 18” Y NAIL (59 used in this step) Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”. Fasten the BACK (F) to your unit using the NAILS (Y).
S p te 7 L L X BROWN 7/16" LARGE HEAD SCREW (12 used in this step) Fasten six HINGES (L) to the DOORS (G). Use twelve BROWN 7/16" LARGE HEAD SCREWS (X). 413329 www.sauder.
S p te 8 G B P M U SILVER 3/4" MACHINE SCREW (4 used for the PULLS) X BROWN 7/16" LARGE HEAD SCREW (12 used for the HINGES) Carefully stand your unit upright. Fasten the DOOR (G) to the LEFT END (B). Use six BROWN 7/16" LARGE HEAD SCREWS (X). Fasten a PULL (M) to the DOOR (G). Use two SILVER 3/4" MACHINE SCREWS (U). Peel the FELT DISC from the FELT DISC CARD (P). Stick the FELT DISC on the DOOR where it comes in contact with the unit. Repeat this step for the other DOOR (G). Page 12 www.sauder.
S p te 9 J H C H (12 used) Q To cover screws R (8 used) S Push the RUBBER SLEEVES (S) over the METAL PINS (R). Insert the METAL PINS into the hole locations of your choice in the RIGHT END (A) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. Cover all the visible SCREWS with a SCREW COVER (Q). Center a COVER over the head of each SCREW and press firmly. Set the ROD (J) onto the ROD HANGERS. 413329 www.sauder.
S p te 10 BLACK 1-7/8” FLAT HEAD SCREW (1 used into a stud in your wall) T N BLACK 9/16” LARGE HEAD SCREW (1 used into the top of your unit) No load V 35 lbs. 25 lbs. 25 lbs. 60 lbs. We recommend using the SAFETY BRACKET (N) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (V) into the top of the unit and a BLACK 1-7/8” FLAT HEAD SCREW (T) into a stud in your wall. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
Meuble de Rangement / Armoire 413329 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Avec précaution, retourner l’élément sur ses chants avant. Déplier l’ARRIÈRE (F) et le placer sur l’élément. Fixer le DESSUS (D) et la pièce TABLETTE/DESSOUS (E) à l’EXTRÉMITÉ GAUCHE (B). Utiliser quatre VIS NOIRES TÊTE PLATE 48 mm (T). Veiller à avoir des marges égales le long des quatre chants de l’ARRIÈRE (F).
ÉTAPE 9 Enfoncer les MANCHONS EN CAOUTCHOUC (S) sur les GOUPILLES EN MÉTAL (R). Insérer les GOUPILLES EN MÉTAL dans les trous choisis de l’EXTRÉMITÉ DROITE (A) et du MONTANT (C). Poser les TABLETTES RÉGLABLES (H) sur les GOUPILLES EN MÉTAL. Recouvrir toutes les VIS visibles avec un COUVERCLE DE VIS (Q). Centrer le COUVERCLE sur la tête de chaque VIS et appuyer fermement. Placer la TRINGLE (J) sur les SUPPORTS DE TRINGLE (K).
413329 Armario de Almacenamiento / Ropero Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Cuidadosamente voltee la unidad paraque repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobrela unidad. Fije el PANEL SUPERIOR (D) y la parte ESTANTE/ FONDO (E) al EXTREMO IZQUIERDO (B). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (T). PASO 2 Fije el PARAL (C) a la parte ESTANTE/FONDO (E).
PASO 9 Empuje los MANGUITOS DE GOMA (S) sobre las ESPIGAS DE METAL (R). Inserte las ESPIGAS DE METAL dentro de los agujeros al nivel preferido del EXTREMO DERECHO (A) y del PARAL (C). Coloque los ESTANTES AJUSTABLES (H) sobre las ESPIGAS DE METAL. Cubra todos los TORNILLOS visibles con una CUBIERTA DE TORNILLO (Q). Centre una CUBIERTA sobre la cabeza de cada TORNILLO y presione firmemente. Coloque la VARILLA (J) sobre los SOPORTES DE VARILLA (K).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers or shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • El sobrecargo de cajones de cómoda • Un riesgo de lesiones. • La caída de mobiliario inestable. • La rotura de cajones sobrecargados. • Nunca exceder los límites de peso indicados en las instrucciones.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
