sauder.com Holds more than dresses. Dresser Beginnings Collection | Model 413123 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 386513 11/06/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Not actual size Scissors Safety Warranty Page 2 25-26 27 413123 www.sauder.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 16B SLIDE SET - 3 30G DRAWER FRONT BRACKET - 10 1F HIDDEN CAM - 6 14H HINGE - 4 2F CAM DOWEL - 6 1G SAFETY BRACKET - 1 4G METAL BRACKET - 6 5L WARNING LABEL - 1 45K PULL - 5 WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Place heaviest items in the lowest drawers.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push six HIDDEN CAMS (1F) into the ENDS (A and B) and UPRIGHT (C). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. A C Arrow B Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Arrow 1F (6 used) www.sauder.
Step 2 å NOTE: Before beginning this step, separate the SLIDES from the SLIDE SETS (16B) and the DRAWER PINS at the end of the SLIDES using a SCISSORS. Save the DRAWER PINS. You will use them in Step 13. å Fasten the SLIDES (16B) to the RIGHT END (A) and UPRIGHT (C). Use twelve SILVER 3/4" PAN HEAD SCREWS (52S) through the first and last holes in the SLIDES. å 52S NOTE: The SLIDES are marked "RIGHT" and "LEFT" for easy identification.
Step 3 å Fasten the UPRIGHT (C) to the TOP (D). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Long finished edge Finished edge e fac r u S with EN D HID S M CA Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 4 å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten a METAL BRACKET (4G) to the TOP (D). Use a BLACK 9/16" LARGE HEAD SCREW (1S). Some assembly (and snacks) required. 4G 1S BLACK 9/16" LARGE HEAD SCREW (1 used for the METAL BRACKET) These holes must be here. C D Sur E f mo ace wi re h th ole s 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 8 413123 www.sauder.
Step 5 å Fasten the ENDS (A and B) to the TOP (D). Tighten four HIDDEN CAMS. å Fasten the ENDS (A and B) to the BOTTOM (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees Finished edge B with S e c fa AM Sur EN C D HID Finished edge D E ut itho w S e fac AM Sur EN C D HID A 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 6 å Fasten five METAL BRACKETS (4G) to the BOTTOM (E) and SKIRT (I). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the BOTTOM and SKIRT. å Fasten the SKIRT (I) to the ENDS (A and B) and BOTTOM (E). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). B I E A 4G 4G I 1S BLACK 9/16" LARGE HEAD SCREW (10 used for the METAL BRACKETS) 4G Page 10 413123 www.sauder.
Step 7 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C).
Step 8 å å Carefully stand your unit upright. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the DOOR (G) to the LEFT END (B). Use the screws in the HINGES. See the next step for door adjustments. å Fasten a PULL (45K) to the DOOR (G). Use two SILVER 7/8" MACHINE SCREWS (24S). å Repeat this step for the other DOOR (G).
Step 9 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), then turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 10 å Fasten the LARGE DRAWER SIDES (D486) to the LARGE DRAWER BACK (D490). Use four BLACK 1-1/2" PAN HEAD SCREWS (49S). å Slide the DRAWER BOTTOM (D614) into the grooves in the LARGE DRAWER SIDES (D486) and LARGE DRAWER BACK (D490). å Repeat this step for the other drawers. The small drawer will use the DRAWER SIDES (D488) and DRAWER BACK (D491). Be sure the grooves in each part line up with each other on the inside of the drawer.
Step 11 å Push four DRAWER FRONT BRACKETS (30G) into the holes in the LARGE DRAWER SIDES (D486). å Fasten the DRAWER FRONT BRACKETS (30G) to the LARGE DRAWER SIDES (D486). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). å Fasten the LARGE DRAWER FRONT (J) to the LARGE DRAWER SIDES (D486). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the PULL (45K) to the LARGE DRAWER FRONT (J). Use two SILVER 7/8" MACHINE SCREWS (24S). å Repeat this step for the other drawers using the SMALL DRAWER FRONT (N).
Step 12 å With a hammer, gently tap four SHELF SNAPS (6R) into the holes in the ADJUSTABLE SHELF (H). 6R H 6R Page 16 413123 www.sauder.
Step 13 å To insert the drawers into your unit, line up the grooves on the DRAWER SIDES with the SLIDES on your unit. Slide the drawer into the unit until it is about 3" or 4" away from the back of your unit. å Using your hammer, gently tap two DRAWER PINS (from Step 2) into the holes in your DRAWER SIDES (D486 and D488). å NOTE: The DRAWER PINS are used as a locking system for your drawer. When the DRAWER PINS are in place, you will not be able to remove the drawer from your unit.
Step 14 å Apply the WARNING LABEL (5L) to the upper DRAWER SIDE (D488). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram. å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. å Peel the APPLIQUES from the APPLIQUE CARD (29P). Stick the APPLIQUES over the heads of each visible SCREW in the ENDS (A and B).
Modèle 413123 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer les EXTRÉMITÉS (A et B) au DESSUS (D). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer six EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et le MONTANT (C). Ensuite, insérer l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
ÉTAPE 9 ÉTAPE 13 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Il faut peut-être ajuster les PORTES. Suivre les indications ci-dessous pour ajuster. Pour insérer les tiroirs dans l'unité, aligner les rainures des CÔTÉS DE TIROIR avec les COULISSES de l'unité. Faire glisser le tiroir dans l’unité jusqu’à ce qu’il se trouve à environ 76 mm ou 101 mm de l’arrière de l’unité.
Modelo 413123 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije los EXTREMOS (A y B) al PANEL SUPERIOR (D). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje seis EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B) y del PARAL (C). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 9 PASO 12 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Utilizando un martillo, ligeramente golpee cuatro FIADORES DE ESTANTE (6R) dentro de los agujeros del ESTANTE AJUSTABLE (H). Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios. AJUSTE DE LA PUERTA: Para ajustar las PUERTAS de un lado al otro (horizontalmente), gire el tornillo de ajuste hacia el interior o hacia el exterior.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from the bottom to the top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones y estantes sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
