sauder.com Spark your style. SmartCenter™ Secretary Edge Water Collection | 413092 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-32 Français pg 33-36 Español pg 37-40 Lot # 372368 05/08/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-32 Hammer Français 33-36 Español 37-40 Safety 41-42 Warranty Not actual size Skip the power trip. This time. 43 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. S2 R F S2 J X E A I M P AA H Y B BB V U AA W K O V Q T C G L Z D BB N N www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (GG) into the large holes in the UPRIGHTS (C and D). Do not tighten the TWIST-LOCK® FASTENERS in this step. GG C D Page 6 413092 www.sauder.
Step 2 å Push twenty-six HIDDEN CAMS (HH2) into the ENDS (A and B), BOTTOM (G), SHELF (H), TOP SHELF (I), and OUTLET SHELF (J). Then, insert the metal end of a CAM DOWEL (II2) into each HIDDEN CAM, except the long edges of the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Do not insert CAM DOWELS into this edge. Arrow A B Hole Do not insert CAM DOWELS into this edge. G H Arrow I J Arrow (26 used) HH2 II2 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. (18 used) www.
Step 3 å Turn eight CAM SCREWS (JJ2) into the LEGS (P and Q). Remember: Righty tighty. Lefty loosey. (8 used) JJ2 P Q Page 8 413092 www.sauder.
Step 4 å Fasten the LEGS (P and Q) to the ENDS (A and B). Tighten eight HIDDEN CAMS. å Fasten the FEET (BB) to the LEGS (P and Q). Use two BLACK 1-5/8" PAN HEAD SCREWS (CCC). 1 2 These surfaces should be even. These surfaces should be even. P S H urf ID ac D e EN w C ith A M S A Q S H urf ID ac D e EN w C ith A M S B BB Curved edge CCC BB BLACK 1-5/8" PAN HEAD SCREW (2 used in this step) www.sauder.
Step 5 å NOTE: You have the option of fastening the EXTENSION BLOCKS into the hole locations of your choice in the ENDS. This will determine the height of your PRINTER SHELF. Be sure to use the same set of holes on each END. å Fasten the EXTENSION BLOCKS (AA) to the ENDS (A and B). Use four BROWN 1-1/2" FLAT HEAD SCREWS (DDD). å Fasten the CABINET RAILS (40AW and 40AX) to the EXTENSION BLOCKS (AA) on the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (NNN).
Step 6 å Fasten the VALANCES (R and S2) to the TOP (F). Use six BLACK 1-7/8" FLAT HEAD SCREWS (BBB). Curved edge S2 Wide edge Curved edge w ith ou t h ol es Finished edge S ur fa ce S2 F h wit e c fa es Surre hol mo R Wide edge Curved edge BBB BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) www.sauder.
Step 7 å Fasten the RIGHT END (A) to the TOP (F). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. P Roller end F A Sur f a HID ce w DEN ith CA MS Curved edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 12 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 413092 www.sauder.
Step 8 å Fasten the OUTLET SHELF (J) to the OUTLET UPRIGHT (E). Tighten two HIDDEN CAMS. å Insert eight METAL PINS (AAA) into the OUTLET UPRIGHT (E) and OUTLET SHELF (J). å Insert the METAL PINS (AAA) in one end of the OUTLET UPRIGHT (E) and OUTLET SHELF (J) into the holes in the RIGHT END (A). å Push a CORD CLIP (WW) into the hole in the OUTLET SHELF (J). å NOTE: The CORD CLIP is used to manage your cords.
Step 9 å Fasten the TOP SHELF (I) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Fasten the RIGHT UPRIGHT (C) to the TOP SHELF (I). Tighten a TWIST-LOCK® FASTENER. å Push a CORD CLIP (WW) into the hole in the TOP SHELF (I). å NOTE: The CORD CLIP is used to manage your cords. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 10 å å Insert four METAL PINS (AAA) into the SMALL SHELF (L). å Fasten the LEFT UPRIGHT (D) to the TOP SHELF (I). Tighten a TWIST-LOCK® FASTENER. å NOTE: Be sure the METAL PINS in the SMALL SHELF (L) insert into the holes in the LEFT UPRIGHT (D). Insert the METAL PINS (AAA) in one end of the SMALL SHELF (L) into the holes in the RIGHT UPRIGHT (C). Finished edge I C L es hol h t i ew fac r u S D AAA (4 used) Flat edge Surface without TWIST-LOCK® FASTENERS www.sauder.
Step 11 å Fasten the SHELF (H) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Fasten the SHELF (H) to the UPRIGHTS (C and D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (BBB). å Fasten the SHELF MOLDING (Y) to the SHELF (H). Use three BLACK 1-1/4" FLAT HEAD SCREWS (EEE).
Step 12 å Fasten the BOTTOM (G) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Push a DOOR STOP (VV) into the hole in the SHELF MOLDING (Y). Maximum 210 degrees Arrow Minimum 190 degrees Don't worry. It isn't Rome. This can be built in a day. VV A Y G ith e w AMS c a f Sur DEN C D HI Finished edge www.sauder.
Step 13 å Fasten the LEFT END (B) to the TOP (F), TOP SHELF (I), SHELF (H), and BOTTOM (G). Tighten eight HIDDEN CAMS. Maximum 210 degrees å NOTE: Be sure the METAL PINS in the OUTLET UPRIGHT (E) and OUTLET SHELF (J) insert into the holes in the LEFT END (B). Minimum 190 degrees Arrow E J F I H Q B G Page 18 413092 www.sauder.
Step 14 å Fasten six METAL BRACKETS (NN) to the BOTTOM (G) and TOP MOLDING (X). Use six BLACK 9/16" LARGE HEAD SCREWS (JJJ). å NOTE: Be sure the BRACKETS are even with the edges of the BOTTOM and TOP MOLDING. å Fasten the TOP MOLDING (X) to the TOP (F). Use three BLACK 9/16" LARGE HEAD SCREWS (JJJ). å Fasten the SKIRT (Z) to the BOTTOM (G). Use three BLACK 9/16" LARGE HEAD SCREWS (JJJ). NN X JJJ BLACK 9/16" LARGE HEAD SCREW (12 used in this step) Angled edge X F Z G NN www.sauder.
Step 15 å Carefully turn your unit over onto its front edges. Unfold the BACK (M) and lay it over your unit. å Make equal margins along both side edges and bottom edge of the BACK (M). Push on opposite corners of your unit if needed to make it "square". å Fasten the top edge of the BACK (M) to the VALANCE (R). Use six BLACK 9/16" LARGE HEAD SCREWS (JJJ). å å Finish fastening the BACK (M) to your unit using the NAILS (OOO). å NOTE: Perforations have been provided for access through the BACK.
Step 16 å Fasten the DRAWER SIDES (V) to the DRAWER BACK (U) and DRAWER BOTTOM (W). Use eight BROWN 1-1/2" FLAT HEAD SCREWS (DDD). å NOTE: Be sure the smaller holes in the DRAWER SIDES face towards the front. Finished edge DDD BROWN 1-1/2" FLAT HEAD SCREW (8 used in this step) Finished surface V U Finished edge ed h is n Fi e ac rf su The smaller holes should be here. W V The small center hole on the bottom of the DRAWER BOTTOM (W) must be closer to this front edge.
Step 17 å Push two DRAWER FRONT BRACKETS (OO) into the holes in the DRAWER SIDES (V). å Fasten the DRAWER FRONT BRACKETS (OO) to the DRAWER SIDES (V). Use four BLACK 1/2" FLAT HEAD SCREWS (MMM). å Fasten the DRAWER FRONT (T) to the DRAWER SIDES (V). Use two BLACK 9/16" LARGE HEAD SCREWS (JJJ) through the DRAWER FRONT BRACKETS (OO) on the DRAWER SIDES and into the DRAWER FRONT. å Fasten a KNOB (SS) to the DRAWER FRONT (T). Use a BLACK 7/8" MACHINE SCREW (HHH).
Step 18 å å Carefully turn your drawer over. Fasten the SWIVEL ROLLERS (PP) to the DRAWER BOTTOM (W). Use eight BLACK 9/16" PAN HEAD SCREWS (LLL). Be sure the flat part of the SWIVEL ROLLER is down toward the DRAWER BOTTOM. LLL BLACK 9/16" PAN HEAD SCREW (8 used in this step) PP W www.sauder.
Step 19 å Fasten two STRAIGHT HINGES (RR) to the FLIP DOWN DOOR (O). Use four BLACK 1/2" FLAT HEAD SCREWS (MMM). å Fasten four CURVED HINGES (QQ) to the DOORS (N). Use eight BLACK 1/2" FLAT HEAD SCREWS (MMM). MMM BLACK 1/2" FLAT HEAD SCREW (12 used in this step) O QQ RR N N QQ Page 24 413092 www.sauder.
Step 20 å Fasten the LIDSTAYS (LL) to the FLIP DOWN DOOR (O). Use four BLACK 9/16" LARGE HEAD SCREWS (JJJ). JJJ BLACK 9/16" LARGE HEAD SCREW (4 used in this step) LL O LL www.sauder.
Step 21 å å Carefully stand your unit upright. å Fasten the FLIP DOWN DOOR (O) to the SHELF (H). Use the screws in the STRAIGHT HINGES (RR). See step 23 for door adjustments. å Fasten the LIDSTAYS (LL) to the ENDS (A and B). Use four BLACK 9/16" PAN HEAD SCREWS (LLL). å Fasten six KNOBS (SS) to the FLIP DOWN DOOR (O). Use six BLACK 7/8" MACHINE SCREWS (HHH). Pro Tip: Lift with your legs. And, you know, your arms.
Step 22 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten a DOOR (N) to the RIGHT END (A). Use the screws in the HINGES. See the next step for door adjustments. å Fasten a KNOB (SS) and BACKPLATE (TT) to the DOOR (N). Use a BLACK 1-1/8" MACHINE SCREW (FFF). å Repeat this step for the other DOOR (N).
Step 23 å å Refer to the enlarged diagram to identify the parts on the HINGES. å å DOOR ADJUSTMENTS: å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOOR up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOOR in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 24 å Fasten the DRAWER SLIDES (40AY and 40AZ) to the PRINTER SHELF (K). Use four BROWN 1" FLAT HEAD SCREWS (GGG). å NOTE: The DRAWER SLIDES are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å Push a CORD CLIP (WW) into the hole in the bottom of the PRINTER SHELF (K). å NOTE: The CORD CLIP is used to manage your cords. WW Roller end A 40 Z ed h is n Fi K e ac rf su Roller end GGG Long finished edge 4 Y A 0 GGG BROWN 1" FLAT HEAD SCREW (4 used in this step) www.
Step 25 å Insert the Drawer half way into your unit. Then, insert two LONG METAL PINS (ZZ) into the holes in the bottom of the SMALL SHELF (L). å NOTE: The LONG METAL PINS are used as a locking system for your drawer. When the LONG METAL PINS are in place, you will not be able to remove the drawer from your unit. ZZ L Page 30 413092 www.sauder.
Step 26 å Turn four SILVER 5/8" FLAT HEAD SCREWS (III) halfway into the holes in the OUTLET SHELF (J). Do not completely tighten the SCREWS. å Then, slide the OUTLET (KK) onto the heads of the SCREWS in the OUTLET SHELF (J). å Insert the GROMMETS (UU) into the large holes in the SHELVES (I and J). J KK III SILVER 5/8" FLAT HEAD SCREW (4 used for the OUTLET) I UU www.sauder.
Step 27 å To insert the PRINTER SHELF (K) into your unit, tip the front of the SHELF down and drop the rollers on the SHELF behind the rollers on the unit. Lift the front of the SHELF up and slide it into the unit. å å Push a CAM COVER (YY) onto each visible HIDDEN CAM. å We recommend using the SAFETY BRACKET (MM) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (JJJ) into the right or left side of the unit and a BLACK 1-7/8” FLAT HEAD SCREW (BBB) into a stud in your wall.
413092 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (GG) dans les gros trous des MONTANTS (C et D). ÉTAPE 2 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape.
ÉTAPE 10 (SUITE) ÉTAPE 15 (SUITE) Fixer le MONTANT GAUCHE (D) à la TABLETTE SUPÉRIEURE (I). Serrer une FIXATION TWIST-LOCK® Fixer le chant supérieur de l'ARRIÈRE (M) au LAMBREQUIN (R). Utiliser six VIS NOIRES TÊTE LARGE 14 mm (JJJ). REMARQUE : S'assurer de bien insérer les GOUPILLES EN MÉTAL situées sur la PETITE TABLETTE (L) dans les trous du MONTANT GAUCHE (D). Finir de fixer l'ARRIÈRE (M) à l'élément à l'aide des CLOUS (OOO). ÉTAPE 11 Fixer la TABLETTE (H) à l'EXTRÉMITÉ DROITE (A).
ÉTAPE 20 ÉTAPE 24 Fixer le COMPAS (LL) sur la PORTE RABATTANTE (O). Utiliser quatre VIS NOIRES TÊTE LARGE 14 mm (JJJ). Fixer les COULISSES DE TIROIR (40AY et 40AZ) à la TABLETTE POUR IMPRIMANTE (K). Utiliser quatre VIS MARRON TÊTE PLATE 25 mm (GGG). ÉTAPE 21 REMARQUE : Les COULISSES DE TIROIR ont une inscription “DRAWER RIGHT” (droite) et une inscription “DRAWER LEFT” (gauche) pour faciliter leur identification. Relever, avec précaution, l'élément dans sa position verticale.
413092 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (GG) dentro de los agujeros grandes de los PARALES (C y D). PASO 2 Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (F). Apriete dos EXCÉNTRICOS ESCONDIDOS.
PASO 10 (CONTINUACIÓN) PASO 15 (CONTINUACIÓN) Fije el PARAL IZQUIERDO (D) al ESTANTE SUPERIOR (I). Apriete un SUJETADOR TWIST-LOCK®. El margen a lo largo de los bordes laterales e inferior del DORSO (M) debe estar uniforme. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada." NOTA: Asegúrese que las ESPIGAS DE METAL sujetadas al ESTANTE PEQUEÑO (L) se inserten dentro de los agujeros del PARAL IZQUIERDO (D). Fije el borde superior del DORSO (M) a la CORNISA (R).
PASO 20 PASO 24 Fije el FIJADOR DE LA TAPA (LL) a la PUERTA ABATIBLE HACIA ABAJO (O). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (JJJ). Fije las CORREDERAS DE CAJÓN (40AY y 40AZ) al ESTANTE PARA LA IMPRESORA (K). Utilice cuatro TORNILLOS MARRONES DE CABEZA PERDIDA de 25 mm (GGG). PASO 21 NOTA: Las CORREDERAS DE CAJÓN tienen una inscripción "DRAWER RIGHT" (derecha) y una inscripción "DRAWER LEFT" (izquierda) para identificarlas fácilmente.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
