sauder.com Yes, you still have to dress yourself. 4 Drawer Chest Beginnings Collection | 413082 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-16 Français pg 17-18 Español pg 19-20 Lot # 386565 11/09/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-16 Hammer Français 17-18 Español 19-20 Safety 21-22 Warranty Not actual size Tape Measure 23 Scissors Skip the power trip. This time. Page 2 413082 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 4 16B SLIDE SET - 4 2F CAM DOWEL - 4 5G ANGLE BRACKET - 8 30G DRAWER FRONT BRACKET - 14 5L WARNING LABEL - 1 42P APPLIQUE CARD - 2 1G SAFETY BRACKET - 1 46K KNOB - 8 1R METAL PIN - 4 WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Place heaviest items in the lowest drawers.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push four HIDDEN CAMS (1F) into the ENDS (A2 and B2). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1330 to watch a video on how to assemble your unit. Do not tighten the HIDDEN CAMS in this step.
Step 2 å NOTE: Before beginning this step, separate the SLIDES from the SLIDE SETS (16B) and the DRAWER PINS at the end of the SLIDES using a SCISSORS. Save the DRAWER PINS. You will use them in Step 11. å Fasten the SLIDES (16B) to the ENDS (A2 and B2). Use sixteen SILVER 3/4" PAN HEAD SCREWS (52S) through the first and last holes in the SLIDES. å NOTE: The SLIDES are marked "RIGHT" and "LEFT" for easy identification.
Step 3 å Fasten four ANGLE BRACKETS (5G) to the BACKS (E). Use four BROWN 7/16" LARGE HEAD SCREWS (6S). å Fasten two ANGLE BRACKETS (5G) to the SKIRT (G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the BACKS and SKIRT. 6S BROWN 7/16" LARGE HEAD SCREW (4 used for the BACKS) 5G S w urf ith a c h e ol es E S w urf ith a c h e ol es E G 5G 1S BLACK 9/16" LARGE HEAD SCREW (2 used for the SKIRT) www.sauder.
Step 4 å Fasten the ENDS (A2 and B2) to the TOP (C). Tighten four HIDDEN CAMS. Long finished edge Finished edge e fac Sur s ole h h wit C A2 B2 Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 8 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 413082 www.sauder.
Step 5 å å Insert four METAL PINS (1R) into the BACKS (E). å Fasten the BACKS (E) to the ENDS (A2 and B2). Use four BROWN 7/16" LARGE HEAD SCREWS (6S) through the ANGLE BRACKETS on the BACKS and into the ENDS. Insert the METAL PINS (1R) in the BACKS (E) into the holes in the TOP (C). 6S BROWN 7/16" LARGE HEAD SCREW (4 used in this step) A2 C B2 E E 1R The ANGLE BRACKETS should be here. www.sauder.
Step 6 å Fasten the upper BRACES (D) to the ENDS (A2 and B2). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the lower BRACE (D) to the BACKS (E) and ENDS (A2 and B2). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S These holes must be here. These holes must be here. e fac r u S with s ole h e or A2 m D with e c fa Sur s ole h e or m D E B2 es hol e r o 2S E ith ce w a f r Su m D 2S 2S BLACK 1-7/8" FLAT HEAD SCREW (16 used in this step) Page 10 413082 www.sauder.
Step 7 å Fasten two ANGLE BRACKETS (5G) to the upper BRACE (D). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the BRACE (D). å Fasten the SKIRT (G) to the ENDS (A2 and B2) and BRACE (D). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) A2 G D B2 5G www.sauder.
Step 8 å Fasten the LARGE DRAWER SIDES (D486) to the LARGE DRAWER BACK (D487). Use four BLACK 1-1/2" PAN HEAD SCREWS (49S). å Slide the DRAWER BOTTOM (D610) into the grooves in the LARGE DRAWER SIDES (D486) and LARGE DRAWER BACK (D487). å Repeat this step for the other drawers. Use the DRAWER SIDES (D488) and DRAWER BACK (D489) for the small drawer. Be sure the grooves in each part line up with each other on the inside of the drawer.
Step 9 å Push four DRAWER FRONT BRACKETS (30G) into the holes in the LARGE DRAWER SIDES (D486). å Fasten the DRAWER FRONT BRACKETS (30G) to the LARGE DRAWER SIDES (D486). Use eight BLACK 1/2" FLAT HEAD SCREWS (43S). å Repeat this step for the other drawers. The small drawer will only use two DRAWER FRONT BRACKETS. D486 D486 30G 30G 43S BLACK 1/2" FLAT HEAD SCREW (28 used in this step) www.sauder.
Step 10 å Fasten the DRAWER FRONTS (H and L) to the DRAWER SIDES (D486 and D488). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the KNOBS (46K) to the DRAWER FRONTS (H and L). Use four SILVER 7/8" PAN HEAD SCREWS (22S). å Repeat this step for the other drawers. 22S SILVER 7/8" PAN HEAD SCREW ( used in this step) D488 D488 1S L BLACK 9/16" LARGE HEAD SCREW (14 used for the DRAWER FRONTS) 46K D486 D486 H 46K Page 14 413082 www.sauder.
Step 11 å å Carefully stand your unit upright. å Using your hammer, gently tap two DRAWER PINS (from Step 2) into the holes in your DRAWER SIDES (D486). å NOTE: The DRAWER PINS are used as a locking system for your drawer. When the DRAWER PINS are in place, you will not be able to remove the drawer from your unit. å å Repeat this step for the other drawers. To insert the drawer into your unit, line up the grooves on the DRAWER SIDES with the SLIDES on your unit.
Step 12 å Apply the WARNING LABEL (5L) to the upper DRAWER SIDE (D488). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram. å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. å Peel the APPLIQUES from the APPLIQUE CARD (42P). Stick the APPLIQUES over the heads of each visible SCREW in the ENDS (A2 and B2).
413082 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer les CÔTÉS DE GRAND TIROIR (D486) à l'ARRIÈRE DE GRAND TIROIR (D487). Utiliser quatre VIS NOIRES TÊTE PLATE 38 mm (49S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2). Ensuite, insérer l'extrémité en métal d'une CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
413082 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije los LADOS DE CAJÓN GRANDE (D486) al DORSO DE CAJÓN GRANDE (D487). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 38 mm (49S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Deslice el FONDO DE CAJÓN (D610) dentro de las ranuras de los LADOS DE CAJÓN GRANDE (D486) y del DORSO DE CAJÓN GRANDE (D487).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
