413045 TV Stand PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-18 Français ...............Pages 19-21 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ASSEMBLY TOOLS REQUIRED Part Identification .......................3 Hardware Identification .............4 No. 2 Phillips Screwdriver Assembly Steps .................... 5-18 Tip Shown Actual Size Français .............................. 19-21 Espanol............................... 22-24 Hammer Safety ................................. 25-26 Warranty ...................................27 WARNING Use of a TV that is too heavy or large is hazardous.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts.
HARDWARE IDENTIFICATION CABINET RIGHT - 2 35DB CABINET LEFT - 2 35DA R2 HIDDEN CAM - 12 S2 CAM DOWEL - 8 V DRAWER FRONT BRACKET - 2 Y SCREW COVER - 8 Z 35DC DRAWER RIGHT - 2 35DD T2 CAM SCREW - 4 W PULL - 2 METAL PIN - 12 DRAWER LEFT - 2 U ANGLE BRACKET - 6 X FOOT - 1 AA RUBBER SLEEVE - 8 BB WARNING LABEL - 1 (Refer to the last step for proper location and application) CC BLACK 1-7/8" FLAT HEAD SCREW - 12 DD BLACK 1-9/16" FLAT HEAD SCREW - 8 EE SILVER 3/4” MACHINE SCREW - 4 FF GG GOLD
S p te 1 Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips Scan this QR code or go to this address: http://qr.sauder.com/?ID=1192 to watch a video on how to assemble your unit. D Do not tighten the HIDDEN CAMS in this step. Arrow C (8 used) B R2 Arrow A S2 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Do not insert CAM DOWELS into this part.
S p te 2 T2 Q If the STOP MOLDING (Q) has an unfinished surface, it should be positioned here. S H urf ID a c D e E w N it C h A M E S Q Turn four CAM SCREWS (T2) into the STOP MOLDING (Q). Fasten the STOP MOLDING (Q) to the TOP (E). Tighten four HIDDEN CAMS. Page 6 www.sauder.
S p te 3 3 B D 5 S H urf ID a c D e E w N it C h A M S D Finished edge Roller end 35 DA 3 A D 5 S H urf ID a c D e E w N it C h A M A S Roller end S Finished edge S H urf ID a c D e E w N it C h A M B Roller end Finished edge D 35 B GG GOLD 5/16” FLAT HEAD SCREW (8 used in this step) Fasten the CABINET RIGHTS (35DA) and CABINET LEFTS (35DB) to the ENDS (A and B) and SMALL UPRIGHT (D). Use eight GOLD 5/16" FLAT HEAD SCREWS (GG). 413045 www.sauder.
S p te 4 Finished edge Q E Sur fac HID e w DE ith NC AM C ith S w M e fac N CA r u S DE HID S Fasten the LARGE UPRIGHT (C) to the TOP (E). Tighten two HIDDEN CAMS. Caution Risk of damage or injury. Hidden Cams must be completely tightened. Hidden Cams that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 8 Start Arrow Tighten Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
S p te 5 Finished edge C If the SHELF (G) has an unfinished surface, it should be positioned here. G D Surface with HIDDEN CAMS CC BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Maximum 210 degrees Arrow Minimum 190 degrees Fasten the SHELF (G) to the LARGE UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (CC). Fasten the SMALL UPRIGHT (D) to the SHELF (G). Tighten two HIDDEN CAMS. 413045 www.sauder.
S p te 6 These holes must be here. D F Sur f mo ace w re h ith ole s F Sur f mo ace w re h ith ole s CC Z BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) (4 used) Fasten the BOTTOMS (F) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (CC). Insert four METAL PINS (Z) into the BOTTOMS (F). Page 10 www.sauder.
S p te 7 Finished edge Finished edge B E F G F Maximum 210 degrees A Arrow Minimum 190 degrees CC BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) Fasten the ENDS (A and B) to the TOP (E). Tighten four HIDDEN CAMS. Fasten the ENDS (A and B) to the BOTTOMS (F) and SHELF (G). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (CC). NOTE: Be sure the METAL PINS in the BOTTOMS (F) insert into the holes in the ENDS (A and B). 413045 www.sauder.
S p te 8 P B F A U U FF BROWN 7/16" LARGE HEAD SCREW (12 used in this step) P U Fasten six ANGLE BRACKETS (U) to the BOTTOM (F) and SKIRT (P). Use six BROWN 7/16” LARGE HEAD SCREWS (FF). NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the BOTTOM and SKIRT. Fasten the SKIRT (P) to the ENDS (A and B) and BOTTOM (F). Use six BROWN 7/16" LARGE HEAD SCREWS (FF). Page 12 www.sauder.
S p te Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 9 These holes must line up over the UPRIGHTS and SHELF. HH NAIL (42 used in this step) I F X Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it “square”. Fasten the BACK (I) to your unit using the NAILS (HH).
S p te 10 VIEW THE T-SLOT BOX VIDEO Be sure the grooves in each part line up with each other on the inside of the drawer. D41 D69 D40 Groove DD BLACK 1-9/16" FLAT HEAD SCREW (8 used in this step) D41 D69 D967 d he is in F D40 Fasten the DRAWER SIDES (D40 and D41) to the DRAWER BACK (D69). Use four BLACK 1-9/16" FLAT HEAD SCREWS (DD). Slide the DRAWER BOTTOM (D967) into the grooves in the DRAWER SIDES (D40 and D41) and DRAWER BACK (D69). Repeat this step for the other drawer. Page 14 www.
S p te 11 Push down V D40 D41 D40 J FF BROWN 7/16" LARGE HEAD SCREW (4 used in this step) Pull the DRAWER FRONT BRACKETS (V) apart and slide them into the grooves in the DRAWER SIDES (D40 and D41). Fasten the RIGHT DRAWER FRONT (J) to the DRAWER FRONT BRACKETS (V). Use two BROWN 7/16" LARGE HEAD SCREWS (FF). Repeat this step for the other drawer using the LEFT DRAWER FRONT (K). 413045 www.sauder.
S p te 12 Roller end GG 3 D D 5 GOLD 5/16” FLAT HEAD SCREW (8 used in this step) D41 Roller end D40 J W EE SILVER 3/4” MACHINE SCREW (4 used for the PULLS) D 35 C Fasten the DRAWER RIGHT (35DC) and DRAWER LEFT (35DD) to the DRAWER SIDES (D40 and D41). Use four GOLD 5/16" FLAT HEAD SCREWS (GG). Fasten the PULL (W) to the RIGHT DRAWER FRONT (J). Use two SILVER 3/4" MACHINE SCREWS (EE). Repeat this step for the other drawer. Page 16 www.sauder.
S p te 13 B Z H (8 used) AA C H A K J Place the roller on the SLIDE behind the roller on the RAIL. Carefully stand your unit upright. To insert the drawers into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS.
S p te WARNING 14 Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip. BB - The TV must weigh less than 95 lbs. - The base of the TV must be able to sit completely on this shelf. E 95 lbs. B 25 lbs. 25 lbs. 40 lbs. A 15 lbs. each Y (8 used) Apply the WARNING LABEL (BB) to the TOP (E). You should be able to read the label when the TV is removed from the unit.
Meuble téléviseur à écran plat 413045 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou large est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures voire la mort. Un téléviseur trop large pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer le GRAND MONTANT (C) au DESSUS (E). Serrer deux EXCENTRIQUES ESCAMOTABLES. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 9 ÉTAPE 13 Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Relever, avec précaution, l'élément dans sa position verticale. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (I). Si besoin est, enfoncer sur les coins opposés de l'élément pour s'assurer d'être « d'équerre ».
Mueble Televisión para televisor de panel plano 413045 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Fije los GABINETES DERECHOS (35DA) y los GABINETES IZQUIERDOS (35DB) a los EXTREMOS (A y B) y al PARAL PEQUEÑO (D).
PASO 9 PASO 13 Precaución No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente ponga la unidad en posición vertical. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (I) y colóquelo sobre la unidad. Los márgenes a lo largo de los cuatro bordes del DORSO (I) deben estar uniformes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
