sauder.com It stands. You sit. A thing of beauty, this one. Panel TV Stand Carson Forge Collection | Model 412921 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-17 Hammer Français 18-20 Español 21-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. Q2 CAM DOWEL- 16 P2 HIDDEN CAM - 16 U HINGE - 4 V ANGLE BRACKET - 3 Z KNOB - 2 AA METAL PIN - 10 R CORNER BRACKET - 2 W DOOR STOP - 2 BB RUBBER SLEEVE - 8 S X CORNER CAP - 2 CORNER ACCENT - 4 Y T FOOT - 2 ANTI-SKID PAD - 1 CC WARNING LABEL - 1 LL BACKPLATE - 2 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push sixteen HIDDEN CAMS (P2) into the ENDS (A and B), UPRIGHT (C), and SHELF (G). Then, insert the metal end of a CAM DOWEL (Q2) into each HIDDEN CAM. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1565 to watch a video on how to assemble your unit.
Step 2 å Fasten the CORNER ACCENTS (X) to the END MOLDINGS (M). Use four SILVER 1/2" MACHINE SCREWS (JJ). Remember: Righty tighty. Lefty loosey. Surface with more holes X M Surface with more holes These holes are closer to the top edge. X X M X JJ SILVER 1/2" MACHINE SCREW (4 used in this step) Page 6 412921 www.sauder.
Step 3 å Fasten the RIGHT END (A) to the TOP (E). Tighten two HIDDEN CAMS. å å Insert two METAL PINS (AA) into the SMALL UPRIGHT (D). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Insert the METAL PINS (AA) in the SMALL UPRIGHT (D) into the holes in the TOP (E). A withMS e c fa A Sur DEN C HID Edge with HIDDEN CAMS D AA ce les fa o ur h S ith w Finished edge E Curved edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 4 å Fasten the SHELF (G) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Fasten the SHELF (G) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (DD). å Fasten the UPRIGHT (C) to the SHELF (G). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees C A ith e w AMS c a f Sur DEN C HID DD BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) ce rfa Su G th wi EN DD HI S M CA Finished edge D Page 8 412921 www.sauder.
Step 5 å Fasten the LEFT END (B) to the TOP (E) and SHELF (G). Tighten four HIDDEN CAMS. å Fasten the END MOLDINGS (M) to the ENDS (A and B). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees A M Edge with HIDDEN CAMS G ut itho S w e fac CAM r u S DEN HID E B M Edge without CORNER ACCENTS www.sauder.
Step 6 å Fasten the EXTENSION BLOCKS (N and O) to the ENDS (A and B). Use six BROWN 1-1/2" FLAT HEAD SCREWS (EE). å Fasten the BOTTOM (F) to the ENDS (A and B) and UPRIGHT (C). Use six BLACK 1-7/8" FLAT HEAD SCREWS (DD). DD BLACK 1-7/8" FLAT HEAD SCREW (6 used for the BOTTOM) ith w s ce ole fa h ur e S or m Curved edge F A These holes must be here. N C O This hole is closer to the short edge. B EE BROWN 1-1/2" FLAT HEAD SCREW (6 used for the EXTENSION BLOCKS) Page 10 412921 www.sauder.
Step 7 å å Fasten the CORNER BRACKETS (R) to the BOTTOM (F). Use four BLACK 9/16" LARGE HEAD SCREWS (GG). Don't worry. It isn't Rome. This can be built in a day. Push the DOOR STOPS (W) into the holes in the SHELF (G). GG R BLACK 9/16" LARGE HEAD SCREW (4 used for the CORNER BRACKETS) F R G W www.sauder.
Step 8 å å å å Slide the SKIRTS (K and L) onto the CORNER BRACKETS (R). Slide the FEET (T) into the notches in the SIDE SKIRTS (L). HH Fasten the SIDE SKIRTS (L) to the BOTTOM (F). Use two BLACK 9/16" WAFER HEAD SCREWS (HH) through the FEET and into the BOTTOM. Now, slide the CORNER CAPS (S) onto the SKIRTS (K and L). BLACK 9/16" WAFER HEAD SCREW (2 used in this step) S Unfinished edge These holes must be here. T R L K Unfinished edge S F T R Page 12 L 412921 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold the BACK (H) and lay it over your unit. å Make equal margins along all four edges of the BACK (H). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (H) to your unit using the NAILS (KK). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å Fasten three ANGLE BRACKETS (V) to the BOTTOM (F) and FRONT SKIRT (K).
Step 10 å Fasten the HINGES (U) to the DOORS (I). Use eight BLACK 1/2" FLAT HEAD SCREWS (II). II BLACK 1/2" FLAT HEAD SCREW (8 used in this step) U I I U Page 14 412921 www.sauder.
Step 11 å å Carefully stand your unit upright. å Fasten a DOOR (I) to the RIGHT EXTENSION BLOCK (N). Use the screws in the HINGES. See the next step for door adjustments. å Fasten a KNOB (Z) and BACKPLATE (LL) to the DOOR (I). Use a BLACK 1-1/8" MACHINE SCREW (FF). å Pro Tip: Lift with your legs. And, you know, your arms. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram.
Step 12 å å Refer to the enlarged diagram to identify the parts on the HINGES. å å DOOR ADJUSTMENTS: å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 13 å Push the RUBBER SLEEVES (BB) over the remaining METAL PINS (AA). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (J) onto the METAL PINS. å To help prevent the TV from sliding, place the ANTI-SKID PAD (Y) under the front support of the TV or divide among the front supports if more than one. å Apply the WARNING LABEL (CC) to the TOP (E). You should be able to read the label when the TV is removed from the unit.
Modèle 412921 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'EXTRÉMITÉ GAUCHE (B) au DESSUS (E) et à la TABLETTE (G). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les MOULURES D'EXTRÉMITÉ (M) aux EXTRÉMITÉS (A et B). Serrer six EXCENTRIQUES ESCAMOTABLES. Enfoncer seize EXCENTRIQUES ESCAMOTABLES (P2) dans les EXTRÉMITÉS (A et B), le MONTANT (C) et la TABLETTE (G).
ÉTAPE 9 ÉTAPE 12 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (H) et le placer sur l'élément. Il faut peut-être ajuster les PORTES. Suivre les indications ci-dessous pour ajuster. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (H).
Mueble Televisión para televisor de panel plano Modelo 412921 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el ESTANTE (G) al EXTREMO DERECHO (A). Apriete dos EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciséis EXCÉNTRICOS ESCONDIDOS (P2) dentro de los EXTREMOS (A y B), el PARAL (C) y el ESTANTE (G). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (Q2) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 7 PASO 9 Fije las MÉNSULAS DE ESQUINA (R) al FONDO (F). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (GG). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Empuje los TOPES DE PUERTA (W) dentro de los agujeros del ESTANTE (G). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (H) y colóquelo sobre la unidad.
PASO 10 PASO 12 Fije las BISAGRAS (U) a las PUERTAS (I). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (II). Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. PASO 11 Cuidadosamente ponga la unidad en posición vertical. Avant de fixer la PORTE à l’unité, s’assurer que la vis de montage se trouve contre les butées comme l’indique le schéma de droite. Si ce n’est pas le cas, desserrer la vis de montage pour la faire glisser contre les butées.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
