412885 Writing Table PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-15 Français ...............Pages 16-18 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ASSEMBLY TOOLS REQUIRED Part Identification .......................3 No. 2 Phillips Screwdriver Hardware Identification .............4 Tip Shown Actual Size Assembly Steps .................... 5-15 Français .............................. 16-18 Hammer Espanol............................... 19-21 Safety .......................................22 Warranty ...................................23 Page 2 www.sauder.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts.
HARDWARE IDENTIFICATION CABINET RIGHT - 1 35DB CABINET LEFT - 1 35DA P HIDDEN CONNECTOR - 8 T BLACK 1-7/8" FLAT HEAD SCREW - 16 Q PULL - 1 35DC DRAWER RIGHT - 1 35DD R SCREW COVER - 8 DRAWER LEFT - 1 S METAL PIN - 8 30S BLACK 1-9/16" FLAT HEAD SCREW - 4 V BLACK 1-1/8" PAN HEAD SCREW - 8 W BLACK 7/8" LARGE HEAD SCREW - 2 X SILVER 7/8" MACHINE SCREW - 2 Y Z GOLD 5/16" FLAT HEAD SCREW - 8 CONNECTOR SCREW - 8 Screws are shown actual size. You may receive extra hardware with your unit.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 P Z S Insert a CONNECTOR SCREW (Z) into each HIDDEN CONNECTOR (P). p te 2 P (8 used) A Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Use your hammer to tap two HIDDEN CONNECTORS (P) with SCREWS into one of the ENDS (A). Repeat this step for the other END (A), RIGHT UPRIGHT (B), and LEFT UPRIGHT (C). 412885 www.sauder.
S p te 3 Edge and surface with HIDDEN CONNECTORS H A Edge and surface with HIDDEN CONNECTORS G I H Unfinished edge A G S I (8 used) Unfinished edge T BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) Insert eight METAL PINS (S) into the LEGS (H and I). Insert the METAL PINS (S) in the LEGS (H and I) into the holes in the ENDS (A) and STRETCHERS (G). Now, fasten the LEGS (H and I) to the ENDS (A) and STRETCHERS (G). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (T). Page 6 www.sauder.
S p te 4 A I E A V BLACK 1-1/8" PAN HEAD SCREW (4 used in this step) H T BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Fasten the BACK (E) to the LEGS (H and I). Use four BLACK 1-1/8" PAN HEAD SCREWS (V). Fasten the BACK (E) to the ENDS (A). Use two BLACK 1-7/8" FLAT HEAD SCREWS (T). 412885 www.sauder.
S p te 5 How to use the HIDDEN CONNECTOR To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR. While pushing the screw into the hole of the adjoining part, turn the screwdriver clockwise to tighten. ac e A ni sh ed su rf D U n fi A Long finished edge To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR.
S p te 6 I A F H F A V BLACK 1-1/8" PAN HEAD SCREW (4 used in this step) Finished surface T BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Fasten the FRONTS (F) to the LEGS (H and I). Use four BLACK 1-1/8" PAN HEAD SCREWS (V). Fasten the FRONTS (F) to the ENDS (A). Use two BLACK 1-7/8" FLAT HEAD SCREWS (T). 412885 www.sauder.
S p te 7 T Surface with HIDDEN CONNECTORS BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) C E F B D F Surface with HIDDEN CONNECTORS Finished edge Fasten the UPRIGHTS (B and C) to the TOP (D). Tighten four HIDDEN CONNECTORS. Fasten the UPRIGHTS (B and C) to the BACK (E) and FRONTS (F). Use four BLACK 1-7/8” FLAT HEAD SCREWS (T). Page 10 www.sauder.
S p te 8 3 A D 5 3 B D 5 C B Roller end Y GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Fasten the CABINET RIGHT (35DA) and CABINET LEFT (35DB) to the UPRIGHTS (B and C). Use four GOLD 5/16" FLAT HEAD SCREWS (Y). 412885 www.sauder.
S p te 9 30S BLACK 1-9/16" FLAT HEAD SCREW (2 used in this step section) 1 2 D267 D268 D268 D267 D E H CE IS A F IN F UR S D622 D266 D266 Groove Fasten the DRAWER SIDES (D266 and D267) to the DRAWER BACK (D268). Use two BLACK 1-9/16" FLAT HEAD SCREWS (30S). Slide the DRAWER BOTTOM (D622) into the grooves in the DRAWER SIDES (D266 and D267) and DRAWER BACK (D268).
S p te 10 W BLACK 7/8" LARGE HEAD SCREW (2 used in this step) D249 J Fasten the DRAWER FRONT (J) to the DRAWER BOX FRONT (D249). Use two BLACK 7/8" LARGE HEAD SCREWS (W). 412885 www.sauder.
S p te 11 Roller end D 35 D X SILVER 7/8" MACHINE SCREW (2 used for the PULL) D267 Roller end D266 J Q D 35 C Y GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Fasten the DRAWER RIGHT (35DC) and DRAWER LEFT (35DD) to the DRAWER SIDES (D266 and D267). Use four GOLD 5/16" FLAT HEAD SCREWS (Y). Fasten the PULL (Q) to the DRAWER FRONT (J). Use two SILVER 7/8" MACHINE SCREWS (X) through the DRAWER BOX FRONT, through the DRAWER FRONT, and into the PULL. Page 14 www.sauder.
S p te 12 R (8 used) 40 lbs. 5 lbs. To make drawer adjustments, loosen the front SCREWS, make needed adjustments, then tighten the SCREWS. Carefully stand your unit upright. To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. To make adjustments to the drawer, loosen the front SCREWS in the DRAWER SLIDES, make needed adjustments, then tighten the SCREWS.
412885 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Insérer une VIS DE CONNECTEUR (Z) dans chaque CONNECTEUR ESCAMOTABLE (P). Fixer l'ARRIÈRE (E) aux PIEDS (H et I). Utiliser quatre VIS NOIRES TÊTE GOUTTE DE SUIF 28 mm (V). Fixer l’ARRIÈRE (E) aux EXTRÉMITÉS (A). Utiliser deux VIS NOIRES TÊTE PLATE 48 mm (T). ÉTAPE 2 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. ÉTAPE 5 À l'aide d'un marteau, enfoncer deux CONNECTEURS ESCAMOTABLES (P) avec VIS dans l'une des EXTRÉMITÉS (A).
ÉTAPE 7 ÉTAPE 11 Fixer les MONTANTS (B et C) au DESSUS (D). Serrer quatre CONNECTEURS ESCAMOTABLES. Fixer un TIROIR DROIT (35DC) et un TIROIR GAUCHE (35DD) aux CÔTÉS DE TIROIR (D266 et D267). Utiliser quatre VIS DORÉES TÊTE PLATE 8 mm (Y). Fixer les MONTANTS (B et C) à l'ARRIÈRE (E) et aux DEVANTS (F). Utiliser quatre VIS NOIRES TÊTE PLATE 48 mm (T). Fixer la POIGNÉE (Q) au DEVANT DE TIROIR (J).
412885 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 Inserte un TORNILLO CONECTOR (Z) dentro de cada CONECTOR INVISIBLE (P). Fije el DORSO (E) a las PATAS (H e I). Utilice cuatro TORNILLOS NEGROS DE CABEZA REDONDA de 28 mm (V). PASO 2 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Utilizando un martillo, clave dos CONECTORES INVISIBLES (P) con TORNILLOS dentro de uno de los EXTREMOS (A). Repita este paso para el otro EXTREMO (A), el PARAL DERECHO (B) y el PARAL IZQUIERDO (C).
PASO 7 PASO 11 Fije los PARALES (B y C) al PANEL SUPERIOR (D). Apriete cuatro CONECTORES INVISIBLES. Fije un CAJÓN DERECHO (35DC) y un CAJÓN IZQUIERDO (35DD) a los LADOS DE CAJÓN (D266 y D267). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (Y). Fije los PARALES (B y C) al DORSO (E) y a las PARTES DELANTERAS (F). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (T). PASO 8 Fije el GABINETE DERECHO (35DA) y el GABINETE IZQUIERDO (35DB) a los PARALES (B y C).
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
