sauder.com The stories of your life. Library with Doors Palladia Collection | Model 412019 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 357497 12/05/13 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Straight Edge Screwdriver 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification C T T U N U S L H Q L F M H A M Q B E O U P I G G U D T T R K J www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1631 to watch a video on how to assemble your unit. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (V) into the large holes in the ENDS (A and B), BOTTOM (D), and SHELF (E).
Step 2 Fasten two PLINTHS (T) to the ENDS (A and B). Tighten two TWIST-LOCK® FASTENERS. å How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Use the lower large hole in the PLINTH. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 3 å Fasten six ANGLE BRACKETS (W) to the END MOLDINGS (L). Use six BLACK 9/16" LARGE HEAD SCREWS (KK). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the MOLDINGS. KK BLACK 9/16" LARGE HEAD SCREW (6 used in this step) W L L W www.sauder.
Step 4 å Fasten the END MOLDINGS (L) to the ENDS (A and B). Use six BLACK 9/16" LARGE HEAD SCREWS (KK). KK BLACK 9/16" LARGE HEAD SCREW (6 used in this step) L L These edges should be even. Page 8 These edges should be even. A B 412019 www.sauder.
Step 5 å Fasten two HALF DISKS (U) to a VERTICAL MOLDING (M). Use two BROWN 1" FLAT HEAD SCREWS (JJ). å Repeat this step for the remaining HALF DISKS and VERTICAL MOLDING. JJ The large hole should be facing away from the VERTICAL MOLDING (M). BROWN 1" FLAT HEAD SCREW (4 used in this step) U M U Flat edge down The large hole should be facing away from the VERTICAL MOLDING (M). www.sauder.
Step 6 å Fasten the VERTICAL MOLDINGS (M) to the END MOLDINGS (L). Use six SILVER 1-1/8" FLAT HEAD SCREWS (HH). å NOTE: Be sure the HALF DISK is against the PLINTH (T) before tightening any screw. The screws should tighten into the groove of the VERTICAL MOLDING. Do not overtighten. HH SILVER 1-1/8" FLAT HEAD SCREW (6 used in this step) T M L T L M Page 10 412019 www.sauder.
Step 7 å Fasten the HORIZONTAL MOLDING (P) to the SHELF MOLDING (O). Use three SILVER 1-1/8" FLAT HEAD SCREWS (HH). å Fasten the SHELF MOLDING (O) to the SHELF (E). Tighten two TWIST-LOCK® FASTENERS. HH SILVER 1-1/8" FLAT HEAD SCREW (3 used in this step) Curved edge S T urf FA WI ac S ST e w T E LO ith N E C R K S ® E U n fin is h ed su rf ac e P O www.sauder.
Step 8 å Fasten the TOP MOLDING (N) to the TOP (C) as shown in the upper diagram below. Use three SILVER 1-1/8" FLAT HEAD SCREWS (HH). å Fasten the LEFT END (B) to the TOP (C). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (D), SHELF (E), and PLINTH (T) to the LEFT END (B). Tighten five TWIST-LOCK® FASTENERS. å Fasten the BOTTOM MOLDING (R) to the BOTTOM (D). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 9 å Fasten the remaining PLINTH (T) to the RIGHT END (A). Tighten the TWIST-LOCK® FASTENER. å Fasten the RIGHT END (A) to the TOP (C), SHELF (E), and BOTTOM (D). Tighten six TWIST-LOCK® FASTENERS. C S NER E T S ® FA K LOC E T e fac Sur D ISTW T out with A Curved edge These surfaces should be even. www.sauder.
Step 10 å Fasten the BACK SKIRT (K) to the SKIRT (J). Use four BROWN 1" FLAT HEAD SCREWS (JJ). å Fasten two TIE PLATES (Y) to the BACK SKIRT (K) and four TIE PLATES (Y) to the VALANCE (S). Use six BLACK 9/16" LARGE HEAD SCREWS (KK). JJ BROWN 1" FLAT HEAD SCREW (4 used for the SKIRTS) K ce fa ur S ith w s le ho J (6 used) ed h is fin n U S Y e ac rf su KK BLACK 9/16" LARGE HEAD SCREW (6 used for the TIE PLATES) Page 14 412019 www.sauder.
Step 11 å å Carefully turn your unit over onto its front edges. å Fasten the METAL BRACKETS (X) to the BOTTOM (D) and BACK SKIRT (K). Use four BLACK 9/16" LARGE HEAD SCREWS (KK). å Fasten the VALANCE (S) to the PLINTHS (T). Use four BLACK 9/16" LARGE HEAD SCREWS (KK). Fasten the BACK SKIRT (K) to the lower PLINTHS (T). Use two BLACK 9/16" LARGE HEAD SCREWS (KK). T KK BLACK 9/16" LARGE HEAD SCREW (10 used in this step) S Rounded edge T D K T X T www.sauder.
Step 12 å å Unfold the BACK (F) and lay it over your unit. å å Fasten the BACK (F) to your unit using the NAILS (MM). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square".
Step 13 å Fasten the HINGES (AA) to the DOORS (G). Use eight BLACK 1/2" FLAT HEAD SCREWS (LL). LL AA BLACK 1/2” FLAT HEAD SCREW (8 used in this step) G G AA www.sauder.
Step 14 å å Carefully stand your unit upright. å Fasten a DOOR (G) to the LEFT END (B). Use the screws in the HINGES. See the next step for adjustments. å Fasten a KNOB (EE) to the DOOR (G). Use a BLACK 1-1/8" MACHINE SCREW (II). å Repeat this step for the other door. NOTE: You may need to loosen the mounting and adjusting screws to slide the hinge part way out of the slot before fastening it to the END. Retighten the screw before you mount the HINGE to the END.
Step 15 å å å å å Refer to the enlarged diagram to identify the parts on the HINGES. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments. Follow the text below to make needed adjustments. DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out.
Step 16 å Push two DOOR STOPS (DD) into the holes in the LOWER ADJUSTABLE SHELF (I). å Slide the ADJUSTABLE SHELF MOLDING (Q) onto the notched edge of the SHELF (H). å *U.S. Patent No. 5,499,886 I DD Q H These edges should be even. Notched edge Page 20 412019 www.sauder.
Step 17 å Push the RUBBER SLEEVES (CC) over the METAL PINS (BB). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (H and I) onto the METAL PINS. å Center a SCREW COVER (FF) over the head of each SCREW and press firmly. No load FF (3 used) H To cover screws 25 lbs. H 25 lbs. BB (12 used) B CC 35 lbs. A I 25 lbs. 35 lbs. BB CC www.sauder.
Step 18 å We recommend using the SAFETY BRACKET (Z) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (KK) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (GG) into a stud in your wall. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Modèle 412019 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les MOULURES VERTICALES (M) aux MOULURES D'EXTRÉMITÉ (L). Utiliser six VIS ARGENTÉES TÊTE PLATE 28 mm (HH). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (V) dans les gros trous dans les EXTRÉMITÉS (A et B), le DESSOUS (D) et la TABLETTE (E).
ÉTAPE 11 ÉTAPE 15 Avec précaution, retourner l'élément sur ses chants avant. Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Fixer la PLINTHE ARRIÈRE (K) sur les PLINTHES inférieures (T). Utiliser deux VIS NOIRES TÊTE LARGE 14 mm (KK). Fixer les CONSOLES EN MÉTAL (X) sur le DESSOUS (D) et la PLINTHE ARRIÈRE (K). Utiliser quatre VIS NOIRES TÊTE LARGE 14 mm (KK). Fixer le LAMBREQUIN (S) sur les PLINTHES (T). Utiliser quatre VIS NOIRES TÊTE LARGE 14 mm (KK).
Modelo 412019 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije las MOLDURAS VERTICALES (M) a las MOLDURAS DE EXTREMO (L). Utilice seis TORNILLOS PLATEADOS DE CABEZA PERDIDA de 28 mm (HH). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (V) dentro de los agujeros grandes de los EXTREMOS (A y B), del FONDO (D) y del ESTANTE (E).
PASO 11 PASO 15 Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Fije el FALDÓN POSTERIOR (K) a las BASES más bajos (T). Utilice dos TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (KK). Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios. Fije los SOPORTES DE METAL (X) al FONDO (D) y al FALDÓN POSTERIOR (K).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
