sauder.com Sit and surf. Desk Shoal Creek Collection | 411961 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 364958 10/16/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 411961 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2 2F CAM DOWEL - 6 8F CAM SCREW - 10 BB ANGLE BRACKET - 3 CC SLIDE CAM - 4 DD PULL - 2 FF SUPPORT PIN - 6 GG CAM COVER - 8 1F Page 4 40CA CABINET RIGHT - 2 HIDDEN CAM - 16 411961 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. HH II 30S BLACK 1-9/16" FLAT HEAD SCREW - 8 BLACK 2-1/4" FLAT HEAD SCREW - 6 JJ SILVER 5/8" MACHINE SCREW - 4 KK BLACK 9/16" FLAT HEAD SCREW - 4 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), and MODESTY PANEL (E). Then, insert the metal end of six CAM DOWELS (2F) into the HIDDEN CAMS, except the long edges of the ENDS (A and B) and MODESTY PANEL (E). Do not tighten the HIDDEN CAMS in this step.
Step 2 å Turn ten CAM SCREWS (8F) into the LEGS (H, I, and J). Remember: Righty tighty. Lefty loosey. (10 used) 8F J H J I www.sauder.
Step 3 å Fasten the FRONT LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS. These surfaces should be even. Angled edge H These surfaces should be even. S HI urfa DD ce EN wi CA th M S A S HI urfa DD ce EN wi CA th M S B I Angled edge 1 2 Page 8 411961 www.sauder.
Step 4 å Turn four BLACK 9/16" FLAT HEAD SCREWS (KK) into the other surfaces of the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å Slide the SIDE MOLDINGS (P) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS.
Step 5 å Turn the ENDS (A and B) over and fasten the REAR LEGS (J) to the ENDS. Use six BLACK 2-1/4" FLAT HEAD SCREWS (HH). HH BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) These surfaces should be even. These surfaces should be even. S HI urfa DD ce EN wi CA th M S A J J B S HI urfa DD ce EN wi CA th M S Angled edge Page 10 411961 www.sauder.
Step 6 å Fasten the CABINET RIGHT (40CA) to the RIGHT END (A) and CABINET LEFT (40CB) to the UPRIGHT (C). Use four GOLD 5/16" FLAT HEAD SCREWS (LL) through holes #1 and #4. LL GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end 1 2 3 4 4 A S HI urfa DD ce EN wi CA th M S 3 Roller end 2 H S HI urfa DD ce EN wi CA tho M ut S 1 C Finished edge www.sauder.
Step 7 å Fasten the CABINET RIGHT (40CA) to the other surface of the UPRIGHT (C) and CABINET LEFT (40CB) to the LEFT END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (LL) through holes #1 and #4. LL Roller end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) 1 2 Finished edge 3 S HI urfa DD ce EN wi CA th M S 4 4 3 Roller end C 2 1 S HI urfa DD ce EN wi CA th M S B I Page 12 411961 www.sauder.
Step 8 å Fasten the MODESTY PANEL (E) to the ENDS (A and B). Tighten four HIDDEN CAMS. Now might be a good time to refresh your drink. H A Sur HIDface w DEN ith CA MS These holes must be here. S HI urfa DD ce EN wi CA th M S E B I Sur HIDface w DEN itho CA ut MS 1 2 www.sauder.
Step 9 å Fasten three ANGLE BRACKETS (BB) to the MODESTY PANEL (E). Use three BLACK 9/16" LARGE HEAD SCREWS (JJ). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the MODESTY PANEL. å Fasten the ENDS (A and B) to the TOP (D). Tighten four HIDDEN CAMS. å Then, fasten the MODESTY PANEL (E) to the TOP (D). Use three BLACK 9/16" LARGE HEAD SCREWS (JJ) through the ANGLE BRACKETS on the MODESTY PANEL and into the TOP.
Step 10 å Fasten the UPRIGHT (C) to the TOP (D). Tighten two HIDDEN CAMS. Finished edge D C Surface with HIDDEN CAMS Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 11 å With your hammer, gently tap six SUPPORT PINS (FF) into the DRAWER FRONT (K) and DRAWER BACK (D442). FF K D442 Page 16 411961 www.sauder.
Step 12 VIEW THE T-LOCK BOX VIDEO å Insert the DRAWER SIDES (D20 and D21) at an angle into the slot at each end of the DRAWER FRONT (K). å Slide the DRAWER BOTTOM (D733) into the grooves in the DRAWER SIDES (D20 and D21) and DRAWER FRONT (K). å Repeat this step for the small drawer. The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. D20 K D21 With the palm of your hand, tap the DRAWER BOTTOM down into the groove.
Step 13 å Fasten the DRAWER BACK (D442) to the DRAWER SIDES (D20 and D21). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å NOTE: Be sure the DRAWER BOTTOM (D733) inserts into the groove of the DRAWER BACK (D442). å Repeat this step for the small drawer. 30S BLACK 1-9/16" FLAT HEAD SCREW (8 used in this step) Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. D442 D20 D733 D21 Page 18 411961 www.sauder.
Step 14 å å Insert a SLIDE CAM (CC) into the DRAWER SIDES (D20 and D21). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the small drawer. Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D20 and D21). Use four GOLD 5/16" FLAT HEAD SCREWS (LL) through holes #2 and #4.
Step 15 å Fasten a PULL (DD) to the DRAWER FRONT (K). Use two SILVER 5/8" MACHINE SCREWS (II). å å Repeat fastening a PULL (DD) to the small drawer. Insert the DRAWER DIVIDER (F2) down through the SUPPORT PINS on the DRAWER FRONT (K) and DRAWER BACK (D442). Finished edge II SILVER 5/8" MACHINE SCREW (4 used for the PULLS) F2 D442 DD Page 20 K 411961 www.sauder.
Step 16 å å Carefully stand your unit upright. å Push a CAM COVER (GG) onto each visible HIDDEN CAM. Pro Tip: Lift with your legs. And, you know, your arms. To insert the drawers into your unit, tip the front of the drawers down and drop the rollers on the drawers behind the rollers on the unit. Lift the front of the drawers up and slide them into the unit. 50 lbs. 5 lbs. 10 lbs. GG (8 used) To cover HIDDEN CAMS www.sauder.
Step 17 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
411961 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'ÉLÉMENT DROITE (40CA) sur l'autre surface du MONTANT (C) et l'ÉLÉMENT GAUCHE (40CB) à l’EXTRÉMITÉ GAUCHE (B). Utiliser quatre VIS DORÉES TÊTE PLATE 8 mm (LL) à travers les trous nº 1 et nº 4. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer seize EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C) et le VOILE DE FOND (E).
ÉTAPE 12 ÉTAPE 15 Insérer les CÔTÉS DE TIROIR (D20 et D21) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (K). Fixer une POIGNÉE (DD) sur le DEVANT DE TIROIR (K). Utiliser deux VIS À MÉTAUX 16 mm ARGENT (II). Enfiler le FOND DE TIROIR (D733) dans les rainures des CÔTÉS DE TIROIR (D20 et D21) et du DEVANT DE TIROIR (K). Répéter cette étape pour l'autre tiroir. Répéter cette étape pour le petit tiroir. ÉTAPE 13 Fixer l'ARRIÈRE DE TIROIR (D442) aux CÔTÉS DE TIROIR (D20 et D21).
411961 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije un GABINETE DERECHO (40CA) a la otra superficie del PARAL (C) y un GABINETE IZQUIERDO (40CB) al EXTREMO IZQUIERDO (B). Utilice cuatro tornillos DORADOS de cabeza PERDIDA de 8 mm (LL) a través de los agujeros No. 1 y No. 4. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 12 PASO 15 Fixer l'ARRIÈRE DE TIROIR (D442) aux CÔTÉS DE TIROIR (D20 et D21). Utiliser quatre VIS TÊTE PLATE 40 mm NOIRES (30S). Fije un TIRADOR (DD) a la CARA DE CAJÓN (K). Utilice dos TORNILLOS PLATEADOS PARA METAL de 16 mm (II). REMARQUE : S'assurer que le FOND DE TIROIR (D733) s'encastre dans la rainure de l'ARRIÈRE DE TIROIR (D442). Repita este paso para el otro cajón. Répéter cette étape pour le petit tiroir. PASO 13 Fije el DORSO DE CAJÓN (D442) a los LADOS DE CAJÓN (D20 y D21).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
