sauder.com Legitimizing bedrooms everywhere. Full/Queen Headboard Palladia Collection | 411840 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-14 Français pg 15-16 Español pg 17-18 Lot # 361431 04/08/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-14 Hammer Français 15-16 Español 17-18 Warranty Page 2 Not actual size 19 411840 www.sauder.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. O Q P WASHER - 4 R HOLE PLUG - 3 NUT - 4 SCREW COVER - 3 S SILVER 2" BOLT - 4 T BROWN 1-1/2" FLAT HEAD SCREW - 9 U SILVER 1-1/4" PAN HEAD SCREW - 18 V BROWN 1" FLAT HEAD SCREW - 20 W BLACK 3/4" PAN HEAD SCREW - 5 Page 4 411840 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1196 to watch a video on how to assemble your unit. Fasten the PLINTHS (L and M) to the BACKS (C and D). Use eight BROWN 1" FLAT HEAD SCREWS (V).
Step 2 Fasten the HALF DISKS (N) to the SIDE MOLDINGS (K). Use two BROWN 1" FLAT HEAD SCREWS (V). å å Fasten the BACKS (C and D) to the SIDE MOLDINGS (K). Use six BROWN 1" FLAT HEAD SCREWS (V). å NOTE: There are no pre-drilled holes in the SIDE MOLDINGS. The SCREWS will tighten into the grooves. The larger hole should be facing up. N N V K BROWN 1" FLAT HEAD SCREW (8 used in this step) K Surface with more holes L N L C N K D M K M Page 6 411840 Finished edge www.sauder.
Step 3 å Fasten the TOP MOLDING (I) to the BACK (B). Use four BROWN 1-1/2" FLAT HEAD SCREWS (T). Finished edge r Su h wit e fac s ole h er few B I T Unfinished surface BROWN 1-1/2" FLAT HEAD SCREW (4 used in this step) Flat edge www.sauder.
Step 4 å å With someone’s help, carefully set the unit onto its top. Fasten the TOP MOLDING (I) to the TOP (A). Use five BLACK 3/4" PAN HEAD SCREWS (W). h wit e c rfa u S s ole h er few I A Long finished edge W BLACK 3/4" PAN HEAD SCREW (5 used in this step) Page 8 411840 www.sauder.
Step 5 å Fasten the VALANCE MOLDING (J) to the VALANCE (H). Use three BROWN 1-1/2" FLAT HEAD SCREWS (T). T BROWN 1-1/2" FLAT HEAD SCREW (3 used in this step) Rounded edge J If the VALANCE (H) has a finished surface, it should be facing this direction. H www.sauder.
Step 6 å Fasten the VALANCE (H) to the BACK (B). Use four BROWN 1" FLAT HEAD SCREWS (V). V BROWN 1" FLAT HEAD SCREW (4 used in this step) h wit e c rfa u S s ole h er few J B H Page 10 411840 Rounded edge www.sauder.
Step 7 å Fasten the LEG EXTENSIONS (G) to the BACKS (C and D) as shown in the upper diagram. Use two BROWN 1-1/2" FLAT HEAD SCREWS (T). å Fasten the LEGS (E and F) to the BACKS (B, C, and D) as shown in the lower diagram. Use eighteen SILVER 1-1/4" PAN HEAD SCREWS (U). IMPORTANT: If you will be fastening this headboard to the 413998 Platform Bed, skip step 7. The LEG EXTENSIONS (G) will not be used. Go to step 8 now.
Step 8 å Fasten the LEGS (E and F) to the BACKS (B, C, and D). Use eighteen SILVER 1-1/4" PAN HEAD SCREWS (U). These holes are closer to the long edge. F D B E C U SILVER 1-1/4" PAN HEAD SCREW (18 used in this step) Page 12 411840 www.sauder.
Step 9 å Center three SCREW COVERS (R) over the head of each SCREW in the VALANCE MOLDING (J) and press firmly. å Insert three HOLE PLUGS (Q) into the large holes in the TOP MOLDING (I). R I J Q www.sauder.
Step 10 å å å å Carefully stand your unit upright. Fasten your bed frame to your Headboard. Use the SILVER 2" BOLTS (S), the WASHERS (O), and the NUTS (P). NOTE: Select the holes to use for the correct width of your bed rails. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? P O S O S O SILVER 2" BOLT WASHER (4 of each used in this step) P NUT P S Page 14 411840 www.sauder.
Tête de lit - lit deux places/grand lit deux places 411840 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision.
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer le LAMBREQUIN (H) à l’ARRIÈRE (B). Utiliser quatre VIS MARRON TÊTE PLATE 25 mm (V). Fixer les PLINTHES (L et M) aux ARRIÈRES (C et D). Utiliser huit VIS MARRON TÊTE PLATE 25 mm (V). ÉTAPE 2 Fixer les DEMI-DISQUES (N) aux MOULURES LATÉRALES (K). Utiliser deux VIS MARRON TÊTE PLATE 25 mm (V).
Cabecera de tamaño matrimonial / "reina" 411840 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije la CORNISA (H) al DORSO (B). Utilice cuatro TORNILLOS MARRONES DE CABEZA PERDIDA de 25 mm (V). Fije las BASES (L y M) a los DORSOS (C y D). Utilice ocho TORNILLOS MARRONES DE CABEZA PERDIDA de 25 mm (V). PASO 2 Fije los MEDIOS CÍRCULOS (N) a las MOLDURAS LATERALES (K). Utilice dos TORNILLOS MARRONES DE CABEZA PERDIDA de 25 mm (V).
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.