sauder.com Store behind closed doors. Base Cabinet HomePlus Collection | 411591 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-16 Français pg 17-18 Español pg 19-20 Lot # 360544 02/28/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-16 Hammer Français 17-18 Español 19-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 411591 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) B LEFT END (1) C TOP (1) D BOTTOM (1) E BACK (1) F DOOR (2) G ADJUSTABLE SHELF (1) H FRONT SKIRT (1) J TOP MOLDING (1) R SIDE SKIRT (2) C E J G F B A D F R H R www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push four SAUDER TWIST-LOCK® FASTENERS (L) into the large holes in the ENDS (A and B). å Repeat this step for the TOP (C). Do not tighten the TWIST-LOCK® FASTENERS in this step. (7 used) L B A www.sauder.
Step 2 å Fasten the ENDS (A and B) to the TOP (C). Tighten four TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 3 å Fasten the BOTTOM (D) to the ENDS (A and B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (W). Remember: Righty tighty. Lefty loosey. B Rounded edge A Unfi nish ed sur fac e D W BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 4 å Fasten the TOP MOLDING (J) to the TOP (C). Tighten three TWIST-LOCK® FASTENERS. å Slip a LARGE RUBBER SLEEVE (P) over the TIE PLATE (O). The RUBBER SLEEVE will be a tight fit. å Then, fasten the TIE PLATE (O) to the TOP MOLDING (J). Use a BLACK 9/16" LARGE HEAD SCREW (Z). Z BLACK 9/16" LARGE HEAD SCREW (1 used for the TIE PLATE) O P Wide edge J C Page 8 411591 www.sauder.
Step 5 å Slide the FEET (I and K) into the notches in the SKIRTS (H and R). å Use a hammer to drive a PROPEL NUT (T) into the holes in the FEET (I and K). Now, turn an ADJUSTABLE GLIDE (S) into each PROPEL NUT. S (4 used) T I K R H I K R www.sauder.
Step 6 å å Fasten the SKIRTS (H and R) to the BOTTOM (D). Use four BLACK 9/16" WAFER HEAD SCREWS (AA) through the FEET and into the BOTTOM. Don't worry. It isn't Rome. This can be built in a day. NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise. H D R R AA BLACK 9/16" WAFER HEAD SCREW (4 used in this step) Page 10 411591 www.sauder.
Step 7 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it “square”. å å Fasten the BACK (E) to your unit using the NAILS (CC). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed.
Step 8 å Fasten two HINGES (M) to each DOOR (F). Use eight BLACK 1/2" FLAT HEAD SCREWS (BB). BB BLACK 1/2" FLAT HEAD SCREW (8 used for the HINGES) M F F M Page 12 411591 www.sauder.
Step 9 å å Carefully stand your unit upright. å Fasten the DOOR (F) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. Stop å Fasten a PULL (Q) to the DOOR (F). Use two BLACK 7/8" MACHINE SCREWS (Y). Mounting screw å å Repeat this step for the other DOOR (F). Pro Tip: Lift with your legs. And, you know, your arms.
Step 10 å å å Refer to the enlarged diagram to identify the parts on the HINGES. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 11 å IMPORTANT: Units that are stacked on top of another unit must be attached to each other as indicated in this step. These units must be positioned against a wall and the upper unit must be attached to a wall. å å å You may need someone's help in this step. å NOTE: The holes in the TOP are not through holes. Use a little extra force while turning these SCREWS. STACKING OPTION: (If not stacking units, go to step 12) Remove the SKIRTS from the upper unit.
Step 12 å å Place your unit into its final position against a wall. å Push the RUBBER SLEEVES (V) over the METAL PINS (U). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELF (G) onto the METAL PINS. å å NOTE: Please read the back pages of the instruction booklet for important safety information. Fasten the SAFETY BRACKET (N) for added stability.
411591 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer deux CHARNIÈRES (M) à chaque PORTE (F). Utiliser huit VIS NOIRES TÊTE PLATE 13 mm (BB). Pour commencer l'assemblage, enfoncer quatre FIXATIONS TWIST-LOCK® SAUDER (L) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette étape pour le DESSUS (C). REMARQUE : Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage.
411591 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje cuatro SUJETADORES TWIST-LOCK® SAUDER (L) dentro de los agujeros grandes de los EXTREMOS (A y B). Repita este paso para el PANEL SUPERIOR (C). NOTA: No apriete los SUJETADORES TWIST-LOCK® por ahora. Fije dos BISAGRAS (M) a cada PUERTA (F). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (BB).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
