sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Dresser Shoal Creek Collection | 411201 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification Assembly Steps No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification D I F A G C M73 I E B E H D10 D166 SS M73 D975 D11 D166 M65 K2 D10 D167 D132 D975 D11 D975 M65 D138 M65 Q2 L2 D132 D167 D975 M65 D138 R2 www.sauder.
Hardware Identification 40CA CABINET RIGHT - 6 40CD DRAWER LEFT - 6 CC2 40CB CABINET LEFT - 6 AA2 BB2 HIDDEN CAM - 22 EE PULL - 8 CAM DOWEL - 10 GG METAL PIN - 4 40CC DRAWER RIGHT - 6 HH SLIDE CAM - 12 CAM SCREW -12 FF JJ KNOB - 4 WARNING LABEL - 1 WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Place heaviest items in the lowest drawers.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. KK LL BLACK 1-7/8" FLAT HEAD SCREW - 3 30S BLACK 1-9/16" FLAT HEAD SCREW - 30 VV BLACK 1-1/4" FLAT HEAD SCREW - 4 MM BLACK 1-1/8" MACHINE SCREW - 4 NN SILVER 3/4" MACHINE SCREW - 16 OO BLACK 9/16" FLAT HEAD SCREW - 4 XX BLACK 9/16" LARGE HEAD SCREW - 1 QQ GOLD 5/16" FLAT HEAD SCREW - 48 RR NAIL - 47 BLACK 2-1/4" FLAT HEAD SCREW - 6 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-two HIDDEN CAMS (AA2) into the ENDS (A and B), UPRIGHT (C), BOTTOMS (E), and DRAWER BRACES (M65). Then, insert ten CAM DOWELS (CC2) into the HIDDEN CAMS. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1127 to watch a video on how to assemble your unit.
Step 2 å Turn twelve CAM SCREWS (BB2) into the FRONT LEGS (G and H) and DRAWER FRONTS (K2, L2, Q2, and R2). H G BB2 (12 used) R2 R2 Q2 Q2 L2 K2 www.sauder.
Step 3 å Fasten the REAR LEGS (I) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (KK). Flat edge S H urf ID a D ce E w N i C th A ou M t S B I I S H urf ID a D ce E w N i C th A ou M t S A KK BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Page 8 411201 www.sauder.
Step 4 å Turn four BLACK 9/16" FLAT HEAD SCREWS (OO) into the ENDS (A and B) until the shoulder of the SCREWS rest on the surface of the ENDS. å Slide the END MOLDINGS (M73) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the SCREWS in the ENDS. These edges should be even. S H urf ID a D ce E w N i C th A ou M t S B M73 S H urf ID a D ce E w N i C th A ou M t S A M73 M73 Shoulder These edges should be even. OO BLACK 9/16" FLAT HEAD SCREW (4 used in this step) www.
Step 5 å Fasten the FRONT LEGS (G and H) to the other surface of the ENDS (A and B). Tighten six HIDDEN CAMS. Angled edge S H urf ID a D ce E w N i C th A M S B H G S H urf ID a D ce E w N i C th A M S A 1 2 Page 10 411201 www.sauder.
Step 6 å Fasten the CABINET RIGHTS (40CA) and CABINET LEFTS (40CB) to the ENDS (A and B) and UPRIGHT(C). Use twenty-four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. Roller end 1 2 3 1 4 2 3 3 4 4 1 2 A 3 4 2 1 3 4 2 1 3 B 1 G h S wit CAM e c fa N SurHIDDE 4 2 h S wit CAM e fac N SurHIDDE Roller end H Finished edge Roller end 1 QQ 2 4 GOLD 5/16" FLAT HEAD SCREW (24 used in this step) 3 1 2 4 1 3 2 C 3 4 4 1 3 2 4 www.sauder.
Step 7 å Fasten the LEFT END (B) and UPRIGHT (C) to the TOP (D). Tighten four HIDDEN CAMS. Finished edge Long finished edge H B e fac Sur withDEN HIDMS CA C D Unfi nish ed sur fac e e fac Sur out withDEN HIDMS CA Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 12 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 411201 www.sauder.
Step 8 å å Insert four METAL PINS (GG) into the BOTTOMS (E). å NOTE: Be sure the METAL PINS in the BOTTOMS insert into the holes in the LEFT END. å Fasten the BOTTOMS (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). Fasten the BOTTOMS (E) to the LEFT END (B). Tighten two HIDDEN CAMS.
Step 9 å Fasten the RIGHT END (A) to the TOP (D) and BOTTOMS (E). Tighten four HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the BOTTOMS insert into the holes in the RIGHT END. Maximum 210 degrees Arrow Minimum 190 degrees D E G A E Page 14 411201 www.sauder.
Step 10 å Fasten the BRACE (SS) and FOOT BASE (UU) to the BOTTOM (E). Use four BLACK 1-1/4" FLAT HEAD SCREWS (VV) through the BASE, through the BRACE, and into the BOTTOM. Then, push the FOOT (TT) into the FOOT BASE (UU). å NOTE: Turn the screw end of the FOOT completely in. Adjustments will be made to the FOOT after the unit is standing upright. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”. å å Fasten the BACK (F) to your unit using the NAILS (RR). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 12 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. UN FIN ISH ED D132 D975 D132 D138 Q2 Q2 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å D138 Insert the DRAWER SIDES (D132 and D138) at an angle into the slot at each end of the RIGHT DRAWER FRONT (Q2).
Step 13 å Insert a SLIDE CAM (HH) into the DRAWER SIDES (D132 and D138). å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D132 and D138). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawers.
Step 14 å Fasten the KNOBS (FF) to the SMALL RIGHT DRAWER FRONT (K2). Use two BLACK 1-1/8" MACHINE SCREWS (MM). Repeat this step for the other small drawer. å Fasten the PULLS (EE) to the RIGHT DRAWER FRONT (Q2). Use four SILVER 3/4" MACHINE SCREWS (NN). Repeat this step for the other drawers. MM BLACK 1-1/8" MACHINE SCREW (4 used for the KNOBS) K2 FF Q2 NN SILVER 3/4" MACHINE SCREW (16 used for the PULLS) www.sauder.
Step 15 å å Carefully stand your unit upright. å To insert the drawers into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å Apply the WARNING LABEL (JJ) to the upper DRAWER BOTTOM (D975). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 16 å We recommend using the SAFETY BRACKET (WW) for added stability. Use a BLACK 9/16” LARGE HEAD SCREW (XX) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (LL) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) LL WW BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) XX 40 lbs. 20 lbs. 20 lbs. 35 lbs. each www.sauder.
Step 17 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the cam clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREWS when finished with adjustments. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
411201 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'EXTRÉMITÉ GAUCHE (B) et le MONTANT (C) au DESSUS (D). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer vingt-deux EXCENTRIQUES ESCAMOTABLES (AA2) dans les EXTRÉMITÉS (A et B), le MONTANT (C), les DESSOUS (E) et les ENTRETOISES DE TIROIR (M65).
ÉTAPE 11 ÉTAPE 14 Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer les BOUTONS (FF) au DEVANT DE PETIT TIROIR DROIT (K2). Utiliser deux VIS À MÉTAUX 28 mm NOIRES (MM). Répéter cette étape pour l'autre petit tiroir. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (F) et le placer sur l'élément. Fixer les POIGNÉES (EE) au DEVANT DE TIROIR DROIT (Q2).
411201 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el EXTREMO IZQUIERDO (B) y el PARAL (C) al PANEL SUPERIOR (D). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje veintidós EXCÉNTRICOS ESCONDIDOS (AA2) en los EXTREMOS (A y B), el PARAL (C), los FONDOS (E) y las RIOSTRAS DE CAJÓN (M65). A continuación, inserte diez PASADORES DE EXCÉNTRICO (CC2) dentro de los EXCÉNTRICOS ESCONDIDOS.
PASO 11 PASO 14 Precaución No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije los POMOS (FF) a la CARA DERECHA DE CAJÓN PEQUEÑO (K2). Utilice dos TORNILLOS NEGROS PARA METAL de 28 mm (MM). Repita este paso para el otro cajón pequeño. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobre la unidad. Fije los TIRADORES (EE) a la CARA DERECHA DE CAJÓN (Q2).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from the bottom to the top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones y estantes sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
