sauder.com You are getting sleepy. Very sleepy. Full/Queen Headboard Shoal Creek Collection | 410147 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-20 Hammer Français 21-23 Español 24-26 Warranty Not actual size Skip the power trip. This time. 27 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know our ABCs. Part Identification E H A I C D G H F B M M J K M L www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. N TWIST-LOCK® FASTENER - 6 O2 HIDDEN CAM - 12 P2 CAM DOWEL - 12 Q HEADBOARD BRACKET - 2 R ANGLE BRACKET - 5 S DRAWER FRONT BRACKET - 4 T U KNOB - 2 X Page 4 CAM COVER - 4 V TAPE CARD - 5 Y NUT - 4 410147 W SUPPORT PIN - 4 METAL PIN - 8 Z WASHER - 4 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. AA BLACK 1-1/4" FLAT HEAD SCREW - 4 CC GOLD 1" MACHINE SCREW - 2 DD BLACK 9/16" LARGE HEAD SCREW - 22 EE BLACK 1/2" FLAT HEAD SCREW - 8 FF NAIL - 58 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (N) into the large holes in the UPRIGHTS (C and D). Do not tighten the TWIST-LOCK® FASTENERS in this step. N D C N Page 6 410147 www.sauder.
Step 2 å Push twelve HIDDEN CAMS (O2) into the ENDS (A and B), PANEL (F), and SHELF (G). Then, insert the metal end of a CAM DOWEL (P2) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. P2 Arrow (12 used) O2 G F B A Arrow Arrow 02 P2 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.
Step 3 å Using your hammer, gently tap four SUPPORT PINS (W) into the holes in the ENDS (A and B) and UPRIGHTS (C and D). Remember: Righty tighty. Lefty loosey. W B A C D W Page 8 410147 www.sauder.
Step 4 å Fasten the UPRIGHTS (C and D) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 5 å å Insert four METAL PINS (V) into each SMALL SHELF (H). Insert the METAL PINS (V) in one end of the SMALL SHELVES (H) into the holes in the UPRIGHTS (C and D). Finished edge Un su finis rfa he ce d H D Finished edge V (8 used) C Un su finis rfa he ce d H V Page 10 410147 www.sauder.
Step 6 å Fasten the SHELF (G) to the UPRIGHTS (C and D). Tighten four TWIST-LOCK® FASTENERS. Rounded edge D Su rfa ce w ith HI DD EN CA MS C G www.sauder.
Step 7 å å Fasten the LEFT END (B) to the TOP (E) and SHELF (G). Tighten four HIDDEN CAMS. Now might be a good time to refresh your drink. NOTE: Be sure the METAL PINS in the SMALL SHELF (H) insert into the holes in the LEFT END (B). Angled edge H B h wit S e M c rfa CA u N S E DD I H Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 8 å Fasten five ANGLE BRACKETS (R) to the PANEL (F). Use five BLACK 9/16" LARGE HEAD SCREWS (DD). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the PANEL. å å Carefully stand your unit on its TOP (E). å Then, fasten the PANEL (F) to the SHELF (G). Use five BLACK 9/16" LARGE HEAD SCREWS (DD). DD BLACK 9/16" LARGE HEAD SCREW (10 used in this step) Fasten the PANEL (F) to the LEFT END (B). Tighten two HIDDEN CAMS.
Step 9 å Fasten the RIGHT END (A) to the TOP (E), SHELF (G), and PANEL (F). Tighten six HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the SMALL SHELF (H) insert into the holes in the RIGHT END (A). F ce rfa u S ut ho t i w EN DD HI MS CA G E A H Angled edge Maximum 210 degrees Arrow Minimum 190 degrees Page 14 410147 www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (FF). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 11 å Fasten the DRAWER FRONT BRACKETS (S) to the DRAWER SIDES (M). Use four BLACK 1/2" FLAT HEAD SCREWS (EE). å Then, fasten the DRAWER SIDES (M) to the DRAWER FRONT (K). Use two BLACK 9/16" LARGE HEAD SCREWS (DD). å Repeat this step for the other drawer. EE BLACK 1/2" FLAT HEAD SCREW (8 used for the BRACKETS) S M M Unfinished edge Finished edge DD BLACK 9/16" LARGE HEAD SCREW (4 used for the DRAWER FRONTS) M Finished edge M K Hole is closer to this edge. Page 16 410147 www.sauder.
Step 12 å Peel the double-sided TAPE from the TAPE CARD (U). Apply five pieces of TAPE to the DRAWER FRONT (K). å NOTE: You may want to crease the flap on the DRAWER BOTTOM (J) before applying the BOTTOM to the DRAWER FRONT (K). å Press the flap of the DRAWER BOTTOM (J) onto the DRAWER FRONT (K). å Fasten the DRAWER BACK (L) to the DRAWER SIDES (M). Use two BLACK 1-1/4" FLAT HEAD SCREWS (AA). å Repeat this step for the other drawer.
Step 13 å Carefully turn your drawer over and fold the DRAWER BOTTOM (J) so it rests on the DRAWER BACK (L) and DRAWER SIDES (M). å Fasten the DRAWER BOTTOM (J) to the DRAWER BACK (L) and DRAWER SIDES (M). Use ten NAILS (FF). å Repeat this step for the other drawer. Almost time to celebrate! With a nap. M J L M FF NAIL (20 used in this step) J L M Page 18 410147 www.sauder.
Step 14 å NOTE: You may want to crease the flaps on the DRAWER BOTTOM (J) before applying TAPE to the DRAWER BOTTOM. å Peel the double-sided TAPE from the TAPE CARD (U). Apply four pieces of TAPE to the DRAWER BOTTOM (J) and stick the flaps of the DRAWER BOTTOM (J) onto the TAPE. å Fasten a KNOB (T) to the DRAWER FRONT (K). Use a GOLD 1" MACHINE SCREW (CC). å Repeat this step for the other drawer. Want options? Customize your item with add-on hardware kits available on sauder.com.
Step 15 å å å Carefully stand your unit upright and insert the drawers into your unit. å Fasten the bedframe to the HEADBOARD BRACKETS (Q). Use the SILVER 1-1/4" BOLTS (117S), NUTS (Y) and WASHERS (Z). å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. Push a CAM COVER (X) onto each visible HIDDEN CAM. Fasten the HEADBOARD BRACKETS (Q) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (DD).
Tête de lit - lit deux places/grand lit deux places 410147 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage. Fixer la TABLETTE (G) aux MONTANTS (C et D). Serrer quatre FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (N) dans les gros trous des MONTANTS (C et D). ÉTAPE 2 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape.
ÉTAPE 10 ÉTAPE 13 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Retourner soigneusement le tiroir et plier le FOND DE TIROIR (J) de manière qu’il repose sur l’ARRIÈRE DE TIROIR (L) et les CÔTÉS DE TIROIR (M). Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (I).
Cabecera de tamaño matrimonial / "reina" 410147 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® por ahora. Fije el ESTANTE (G) a los PARALES (C y D). Apriete cuatro SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (N) dentro de los agujeros grandes de los PARALES (C y D). PASO 2 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso.
PASO 10 PASO 13 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Voltee con cuidado el cajón y doble el FONDO DEL CAJÓN (J) de manera que descanse en el DORSO DEL CAJÓN (L) y los LADOS DEL CAJÓN (M). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (I) y colóquelo sobre la unidad. Los márgenes a lo largo de los cuatro bordes del DORSO (I) deben estar uniformes.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
