sauder.com Your everyday "Am I a vampire?" checker. Mirror Shoal Creek Collection | 410133 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-23 Español pg 24-26 Lot # 370509 03/04/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-20 Hammer Français 21-23 Español 24-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 410133 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (P) into the large holes in the ENDS (A and B). Do not tighten the TWIST-LOCK® FASTENERS in this step. P B A www.sauder.
Step 2 å Push four HIDDEN CAMS (1F) into the TOP/BOTTOM MOLDINGS (L2). å Turn four CAM SCREWS (8F) into the MOLDINGS (M2 and N2). Some assembly (and snacks) required. 8F M2 N2 Arrow 1F (4 used) L2 L2 Arrow Do not tighten the HIDDEN CAMS in this step. Hole Page 6 410133 www.sauder.
Step 3 å Using your hammer, gently tap the SUPPORT PINS (W) into the holes in the ENDS (A and B) and UPRIGHT (C). W A W B C W www.sauder.
Step 4 å å å Fasten the ENDS (A and B) to the SHELF (E). Tighten two TWIST-LOCK® FASTENERS. Insert four METAL PINS (X) into the UPRIGHT (C). Insert the METAL PINS (X) in one end of the UPRIGHT (C) into the holes in the SHELF (E). How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2.
Step 5 å Fasten the BOTTOM (D) to the ENDS (A and B) and UPRIGHT (C). Use four BLACK 1-7/8" FLAT HEAD SCREWS (Z). å NOTE: Be sure the METAL PINS in the UPRIGHT (C) insert into the holes in the BOTTOM (D). B C Un fin ish ed su rfa ce A D Z BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Unfinished edge www.sauder.
Step 6 å Fasten the TOP/BOTTOM MOLDINGS (L2) to the MOLDINGS (M2 and N2). Tighten four HIDDEN CAMS. Side Step: Make nachos. (Optional, but recommended.) N2 Su rfa ce wi th e ac rf su HI DD EN CA M S ed h is fin n U L2 The groove must be here. e ac rf su Su rfa ce wi th ed h is fin n U HI DD EN CA M S M2 L2 1 Page 10 2 410133 www.sauder.
Step 7 å Carefully turn the BOTTOM (D) and SHELF (E) over onto their front edges. å Fasten the MOLDINGS (M2 and N2) to the BOTTOM (D) and SHELF (E). Use four BLACK 1-7/8” FLAT HEAD SCREWS (Z). Z N2 L2 Su rfa ce wi th HI DD EN CA M S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) M2 L2 E e ac f r su ed ish n D fi Un For support, place packing foam and magazines here. www.sauder.
Step 8 å Fasten the TOP (K) to the MOLDINGS (L2, M2, and N2). Use three BLACK 1-7/8" FLAT HEAD SCREWS (Z). å Fasten the BACK (I) to the MOLDINGS (L2, M2 and N2). Use twelve BLACK 9/16" LARGE HEAD SCREWS (CC). å NOTE: There are no pre-drilled holes in the MOLDINGS. The SCREWS will tighten into the grooves. Z BLACK 1-7/8" FLAT HEAD SCREW (3 used in this step) These holes are closer to this edge. K L2 N2 L2 Cut-out M2 I CC BLACK 9/16" LARGE HEAD SCREW (12 used for the BACK) Page 12 410133 www.
Step 9 å Place the MIRROR (O) into the MOLDINGS (L2, M2, and N2) with the back side of the MIRROR facing up. å Fasten fourteen MIRROR CLIPS (Y) to the MOLDINGS (L2, M2, and N2). Use fourteen BLACK 9/16" PAN HEAD SCREWS (DD). å NOTE: There are no pre-drilled holes in the MOLDINGS. The SCREWS will tighten into the grooves. DD BLACK 9/16" PAN HEAD SCREW (14 used for the MIRROR CLIPS) (14 used) Y Y L2 R N2 Ba ck sid e of M IR RO L2 O M2 Y Y www.sauder.
Step 10 å Fasten the DRAWER FRONT BRACKETS (T) to the DRAWER SIDES (H). Use eight BLACK 1/2" FLAT HEAD SCREWS (EE). T H H H H T EE BLACK 1/2" FLAT HEAD SCREW (8 used in this step) Page 14 410133 www.sauder.
Step 11 å Fasten the DRAWER SIDES (H) to the DRAWER FRONTS (F). Use four BLACK 9/16" LARGE HEAD SCREWS (CC). å NOTE: Be sure to pay attention to the hole placement for each DRAWER FRONT. CC BLACK 9/16" LARGE HEAD SCREW (4 used for the BRACKETS) Finished edge H Finished edge H Finished edge Use inside hole H F H This hole must be here. Use outside hole This DRAWER FRONT will be now the LEFT DRAWER FRONT (F). Use inside hole F This hole must be here. www.sauder.
Step 12 å Fasten the DRAWER BACK (G) to the DRAWER SIDES (H). Use two BLACK 1-1/4" FLAT HEAD SCREWS (AA). å Peel the double-sided TAPE from the TAPE CARD (U). Apply three pieces of TAPE to the DRAWER FRONT (F) and stick the flap of the DRAWER BOTTOM (J) onto the DRAWER FRONT (F). å Repeat this step for the other drawer. AA U n fin is h ed G su rf ac e BLACK 1-1/4" FLAT HEAD SCREW (4 used in this step) H U F Flap Fi n is h ed J su rf ac e H Page 16 410133 www.sauder.
Step 13 å Carefully turn your drawer over and fold the DRAWER BOTTOM (J) so it rests on the DRAWER BACK (G) and DRAWER SIDES (H). å Fasten the DRAWER BOTTOM (J) to the DRAWER BACK (G) and DRAWER SIDES (H). Use eight NAILS (FF). å Repeat this step for the other drawer. J H G H FF Unfinished surface NAIL (16 used in this step) J G H www.sauder.
Step 14 å NOTE: You may want to crease the flaps on the DRAWER BOTTOM (J) before applying TAPE to the DRAWER BOTTOM. å Peel the double-sided TAPE from the TAPE CARD (U). Apply four pieces of TAPE to the DRAWER BOTTOM (J) and stick the flaps of the DRAWER BOTTOM (J) onto the TAPE. å Fasten the PULL (V) to the DRAWER FRONT (F). Use a GOLD 1" MACHINE SCREW (BB). å Repeat this step for the other drawer. Flap U J J BB GOLD 1" MACHINE SCREW (2 used for the PULLS) F V Page 18 410133 www.sauder.
Step 15 å To mount the Mirror to the 409937 Dresser, you should first cut out the small cut-out squares in the Dresser Back. Perforated cut-out lines have been provided. Then, remove the top Drawers from the Dresser. å Insert the short portion of the MIRROR BRACKETS (S) into the holes in the Dresser Back. å Fasten the short portion of the MIRROR BRACKETS (S) to the Dresser Top. Use six BLACK 9/16" LARGE HEAD SCREWS (CC). å Now, fasten the Mirror to the MIRROR BRACKETS (S).
Step 16 å å Insert the drawers into your unit. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? Left Drawer 3 lbs. 5 lbs. 3 lbs. Right Drawer Page 20 410133 www.sauder.
410133 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les MOULURES SUPÉRIEURES/INFÉRIEURES (L2) aux MOULURES (M2 et N2). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (J) dans les gros trous des EXTRÉMITÉS (A et B).
ÉTAPE 11 ÉTAPE 14 Fixer les CÔTÉS DE TIROIR (H) aux DEVANTS DE TIROIR (F). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (CC). REMARQUE : Il est conseillé de plier les rabats du FOND DE TIROIR (J) avant d’appliquer le RUBAN sur le FOND DE TIROIR. REMARQUE : Suivre attentivement à l'emplacement des trous pour chaque DEVANT DE TIROIR. Décoller le RUBAN double face de la CARTE DE RUBAN ADHÉSIF (U).
410133 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije las MOLDURAS SUPERIORES/INFERIORES (L2) a las MOLDURAS (M2 y N2). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (J) en los agujeros grandes de los EXTREMOS (A y B). PASO 2 Empuje cuatro EXCÉNTRICOS ESCONDIDOS (1F) dentro de las MOLDURAS SUPERIORES/INFERIORES (L2).
PASO 11 PASO 14 Fije los LADOS DE CAJÓN (H) a las CARAS DE CAJÓN (F). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (CC). NOTA: Antes de aplicar la CINTA al FONDO DEL CAJÓN (J), es posible que desee plegar las solapas en el FONDO DEL CAJÓN. NOTA: Preste atención a la colocación de los agujeros para cada CARA DE CAJÓN. Retire la CINTA ADHESIVA de doble faz de la TARJETA CON CINTA (U).
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
