sauder.com For things 'n such. Utility Stand Shoal Creek Collection | 409944 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-19 Français pg 20-22 Español pg 23-25 Lot # 368959 02/17/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-19 Hammer Français 20-22 Español 23-25 Safety 26 Warranty 27 Not actual size Skip the power trip. This time. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification C I D A2 E O G F I F B2 O H D14 D61 D985 D15 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 4B FILE GLIDE - 2 2F 12B FILE BRACKET - 1 CAM DOWEL - 13 W METAL PIN - 4 BB CAM COVER - 1 Page 4 40CC DRAWER RIGHT - 1 8F CAM SCREW - 4 X SLIDE CAM - 2 40CD 1F 409944 HIDDEN CAM - 17 57G FILE BRACKET - 1 Z CC DRAWER LEFT - 1 PULL - 2 FILE ROD - 2 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. EE BLACK 2-1/4" FLAT HEAD SCREW - 4 GG BLACK 9/16" FLAT HEAD SCREW - 4 II GOLD 5/16" FLAT HEAD SCREW - 8 FF SILVER 3/4" MACHINE SCREW - 4 HH BROWN 7/16" LARGE HEAD SCREW - 4 JJ NAIL - 20 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push seventeen HIDDEN CAMS (1F) into the ENDS (A2 and B2), LEGS (G, H, and I), SHELF (E), BOTTOMS (F), and DRAWER BRACE (KK). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the ENDS (A2 and B2). Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the ENDS (A2 and B2). Use four GOLD 5/16" FLAT HEAD SCREWS (II) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. Fasten the REAR LEGS (I) to the ENDS (A2 and B2). Use four BLACK 2-1/4" FLAT HEAD SCREWS (EE). EE BLACK 2-1/4" FLAT HEAD SCREW (4 used for the LEGS) Roller end Surface with HIDDEN CAMS 1 2 3 4 A2 I Roller end 4 3 These holes must be here. I 2 B2 1 Angled edge These holes must be here.
Step 3 å With the REAR LEG (I) on the floor, fasten the LEFT END (B2) to the SHELF (E). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge B2 Un fin ish ed su rfa ce E I Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 4 å Insert a METAL PIN into the holes of each short edge of the BOTTOMS (F). å Fasten the BOTTOMS (F) to the LEFT END (B2). Tighten two HIDDEN CAMS. å NOTE: Be sure the PINS in the BOTTOMS (F) insert into the holes in the LEFT END (B2). Finished edge W B2 Sur fac ew ith HID DEN CA MS F Sur fac ew ith HID DEN CA MS F W Maximum 210 degrees Arrow Finished edge Minimum 190 degrees www.sauder.
Step 5 å With the REAR LEG (I) on the floor, fasten the RIGHT END (A2) to the SHELF (E) and BOTTOMS (F). Tighten four HIDDEN CAMS. å NOTE: Be sure the PINS in the BOTTOMS (F) insert into the holes in the RIGHT END (A2). E F F A2 I Maximum 210 degrees Arrow Minimum 190 degrees Page 10 409944 www.sauder.
Step 6 å Turn four BLACK 9/16" FLAT HEAD SCREWS (GG) into the ENDS (A2 and B2) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å Slide the END MOLDINGS (O) onto the ENDS (A2 and B2). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. GG Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS. BLACK 9/16" FLAT HEAD SCREW (4 used in this step) O GG B2 O Shoulder GG Shoulder A2 www.sauder.
Step 7 å Turn four CAM SCREWS (8F) into the FRONT LEGS (G and H) as shown in the upper diagram below. å Fasten the LEGS (G and H) to the ENDS (A2 and B2) as shown in the lower diagram below. Tighten four HIDDEN CAMS. 8F H G H Angled edge G B2 1 A2 2 Page 12 409944 www.sauder.
Step 8 å Fasten the TOP (C) to the LEGS (G, H, and I). Tighten three HIDDEN CAMS. Finished edge Un fin ish ed su rfa ce H C G I The HIDDEN CAM in this LEG will be tightened in the next step. Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Lay the BACK (D) over your unit. å Make equal margins along the two long and two short edges of the BACK (D). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (D) to your unit using the NAILS (JJ). å Fasten the LEFT REAR LEG (I) to the TOP (C). Tighten the HIDDEN CAM. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 10 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 2 Un fi su nish rfa ed ce D14 D985 D14 J2 D15 J2 D15 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove Insert the DRAWER SIDES (D14 and D15) at an angle into the slot at each end of the DRAWER FRONT (J2).
Step 11 å å Insert a SLIDE CAM (X) into the DRAWER SIDES (D14 and D15). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D14 and D15). Use four GOLD 5/16" FLAT HEAD SCREWS (II) through holes #2 and #4. Roller end Screw head - turn CAM to line up holes in SLIDES with holes in DRAWER SIDES.
Step 12 å Fasten a FILE BRACKET (57G) to the DRAWER FRONT (J2) as shown in the upper diagram below. Use two BROWN 7/16" LARGE HEAD SCREWS (HH). å å å Fasten a FILE BRACKET (12B) to the DRAWER BACK (D61). Use two BROWN 7/16" LARGE HEAD SCREWS (HH). å Slide the FILE RODS (CC) through the holes in the FILE BRACKETS (57G and 12B) and into the FILE GLIDE (4B) on the RIGHT DRAWER SIDE (D14).
Step 13 å å Carefully stand your unit upright. å Push a CAM COVER (BB) onto the HIDDEN CAM on the RIGHT REAR LEG (I). Pro Tip: Lift with your legs. And, you know, your arms. To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. 50 lbs. 25 lbs. 35 lbs. I Page 18 409944 BB www.sauder.
Step 14 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
409944 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Faire tourner quatre VIS TÊTE PLATE 14 mm NOIRES (GG) dans les EXTRÉMITÉS (A2 et B2) jusqu'à ce que l'épaulement des VIS repose sur la surface des EXTRÉMITÉS. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer dix-sept EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2), les PIEDS (G, H et I), la TABLETTE (F) et l'ENTRETOISE DE TIROIR (KK).
ÉTAPE 10 ÉTAPE 13 1. Insérer les CÔTÉS DE TIROIR (D14 et D15) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (J2). Relever, avec précaution, l'élément dans sa position verticale. Pour insérer le tiroir dans l'élément, abaisser le devant du tiroir et faire passer les roulettes situées sur le tiroir derrière les roulettes situées sur l'élément. Relever le devant du tiroir et l'enfiler dans l'élément. 2.
409944 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Con la PATA POSTERIOR (I) sobre el piso, fije el EXTREMO DERECHO (A2) al ESTANTE (E) y a los FONDOS (F). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje diecisiete EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A2 y B2), las PATAS (G, H e I), el ESTANTE (E), los FONDOS (F) y la RIOSTRA DE CAJÓN (KK).
PASO 10 PASO 13 1. Inserte los LADOS DE CAJÓN (D14 y D15) en ángulo en el encaje en cada extremo de la CARA DE CAJÓN (J2). Cuidadosamente ponga la unidad en posición vertical. 2. Deslice el FONDO DE CAJÓN (D985) en las ranuras de los LADOS DE CAJÓN (D14 y D15) y de la CARA DE CAJÓN (J2). 3. Fije la RIOSTRA DE CAJÓN (KK) a la CARA DE CAJÓN (J2). Apriete un EXCÉNTRICO ESCONDIDO. 4. Fije el DORSO DE CAJÓN (D61) a los LADOS DE CAJÓN (D14 y D15) y a la RIOSTRA DE CAJÓN (KK).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
