sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Night Stand Shoal Creek Collection | 409942 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-15 Hammer Français 16-18 Español 19-21 Safety 22 Warranty 23 Not actual size Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification C H E A N F H D B G O N D16 D109 D706 D17 I www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1 T2 U2 CAM DOWEL - 8 V2 CAM SCREW - 4 W KNOB - 1 Z HIDDEN CAM - 12 Y SLIDE CAM - 2 AA BLACK 1-1/8" MACHINE SCREW - 1 BLACK 2-1/4" FLAT HEAD SCREW - 4 BB BLACK 9/16" FLAT HEAD SCREW - 4 CC GOLD 5/16" FLAT HEAD SCREW - 8 DD NAIL - 16 30S BLACK 1-9/16" FLAT HEAD SCREW - 4 Page 4 409942 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twelve HIDDEN CAMS (T2) into the ENDS (A and B) and BOTTOM (D). Then, insert eight CAM DOWELS (U2) into the HIDDEN CAMS. Do not tighten the HIDDEN CAMS in this step. Arrow U2 (8 used) (12 used) T2 Do not insert CAM DOWELS into these edges. D B Arrow A Arrow T2 Arrow Hole www.
Step 2 å Fasten the CABINET RIGHT (35GA) and CABINET LEFT (35GB) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (CC) through holes #1 and #3. å Fasten the REAR LEGS (H) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (Z).
Step 3 å Fasten the LEFT END (B) to the TOP (C). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Roller end Long finished edge C Unfi nish ed sur fac e B ith e w AMS c a f Sur DEN C D HI Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 4 å å å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS. å * U.S. Patent No. 5,499,886 Slide the BOTTOM MOLDING (O) onto the notched edge of the BOTTOM (D). Fasten the RIGHT END (A) to the TOP (C) and BOTTOM (D). Tighten four HIDDEN CAMS. Notched edge B D O Unfi sur nishe fac d e Roller end C D A Maximum 210 degrees Arrow Minimum 190 degrees Page 8 409942 www.sauder.
Step 5 å Turn four BLACK 9/16" FLAT HEAD SCREWS (BB) into the ENDS (A and B) until the shoulder of the SCREWS rest on the surface of the ENDS. å å NOTE: Do not overtighten the SCREWS. å NOTE: If the MOLDINGS come up off of the SCREWS, remove them and slide them on again. Slide the END MOLDINGS (N) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the SCREWS in the ENDS. Apply pressure with your hands as you guide the MOLDINGS onto the ENDS.
Step 6 å å Turn four CAM SCREWS (V2) into the LEGS (F and G). Fasten the LEGS (F and G) to the ENDS (A and B). Tighten four HIDDEN CAMS. (4 used) V2 G F G B F Angled edge A 1 2 Page 10 409942 www.sauder.
Step 7 å Carefully turn your unit over onto its front edges. Lay the BACK (E) over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (E) to your unit using the NAILS (DD). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. DD NAIL (16 used in this step) ed ish fin Un ce rfa su E n io at p rm u fo g in cin d fa te e in b Pr ust m www.sauder.
Step 8 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D706 D16 D16 D17 D17 I I Groove å Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D16 and D17) at an angle into the slot at each end of the DRAWER FRONT (I).
Step 9 å å Insert a SLIDE CAM (Y) into each DRAWER SIDE (D16 and D17). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the DRAWER RIGHT (35GC) and DRAWER LEFT (35GD) to the DRAWER SIDES (D16 and D17). Use four GOLD 5/16" FLAT HEAD SCREWS (CC) through holes #1 and #3. Roller end Screw head - turn CAM to line up holes in SLIDES with holes in DRAWER SIDES. Y 1 Y 3 2 D17 Roller end D16 1 3 2 CC GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.
Step 10 å å Carefully stand your unit upright. å Fasten the KNOB (W) to the DRAWER FRONT (I). Use a BLACK 1-1/8" MACHINE SCREW (AA). To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. AA BLACK 1-1/8" MACHINE SCREW (1 used in this step) 30 lbs. 15 lbs. I W 25 lbs. Page 14 409942 www.sauder.
Step 11 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
409942 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Faire tourner quatre VIS TÊTE PLATE 14 mm NOIRES (BB) dans les EXTRÉMITÉS (A et B) jusqu'à ce que l'épaulement des VIS repose sur la surface des EXTRÉMITÉS. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer douze EXCENTRIQUES ESCAMOTABLES (T2) dans les EXTRÉMITÉS (A et B) et le DESSOUS (D).
ÉTAPE 8 ÉTAPE 10 1 Insérer les CÔTÉS DE TIROIR (D16 et D17) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (I). Relever, avec précaution, l'élément dans sa position verticale. 2 Enfiler le FOND DE TIROIR (D706) dans les rainures des CÔTÉS DE TIROIR (D16 et D17) et du DEVANT DE TIROIR (I). 3 Fixer l'ARRIÈRE DE TIROIR (D109) aux CÔTÉS DE TIROIR (D16 et D17). Utiliser quatre VIS TÊTE PLATE 40 mm NOIRES (30S).
409942 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Atornille cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 14 mm (BB) dentro de los EXTREMOS (A y B) hasta que el resalto de los TORNILLOS repose sobre la superficie de los EXTREMOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje doce EXCÉNTRICOS ESCONDIDOS (T2) dentro de los EXTREMOS (A y B) y el FONDO (D).
PASO 8 PASO 10 1 Inserte los LADOS DE CAJÓN (D16 y D17) en ángulo dentro del encaje en cada extremo de la CARA DE CAJÓN (I). Cuidadosamente ponga la unidad en posición vertical. 2 Deslice el FONDO DE CAJÓN (D706) en las ranuras de los LADOS DE CAJÓN (D16 y D17) y de la CARA DE CAJÓN (I). 3 Fije el DORSO DE CAJÓN (D109) a los LADOS DE CAJÓN (D16 y D17). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 40 mm (30S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
