sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Armoire Shoal Creek Collection | 409934 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-26 Hammer Français 27-29 Español 30-32 Safety 33-34 Warranty Not actual size Skip the power trip. This time. 35 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification J C E G2 A H G2 P J D B I D F P F D26 D174 D981 D27 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. LL BLACK 2-1/4" FLAT HEAD SCREW - 8 MM BLACK 1-7/8" FLAT HEAD SCREW - 1 NN BLACK 1-1/8" MACHINE SCREW - 5 OO SILVER 5/8" FLAT HEAD SCREW - 8 PP BLACK 9/16" LARGE HEAD SCREW - 3 QQ BLACK 9/16" FLAT HEAD SCREW - 4 SS GOLD 5/16" FLAT HEAD SCREW - 8 TT NAIL - 43 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push twenty-one HIDDEN CAMS (V2) into the ENDS (A and B), SHELF/BOTTOMS (D), and DRAWER BRACE (Q2). Then, insert the metal end of twelve CAM DOWELS (W2) into the HIDDEN CAMS, except the long edges of the ENDS (A and B) and the DRAWER BRACE (Q2). Scan this QR code or go to this address: http://qr.
Step 2 å Turn nine CAM SCREWS (X2) into the FRONT LEGS (H and I) and DRAWER FRONT (K). (9 used) X2 K I H www.sauder.
Step 3 å Fasten the CABINET RIGHT (35GA) to the RIGHT END (A) and the CABINET LEFT (35GB) to the END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (SS). Long edge with HIDDEN CAMS Roller end S H urf ID a D ce E w N i C th A M S A 1 2 3 S H urf ID a D ce E w N i C th A M S B Long edge with HIDDEN CAMS 3 2 1 Roller end SS GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 8 409934 www.sauder.
Step 4 å Fasten the REAR LEGS (J) to the ENDS (A and B). Use eight BLACK 2-1/4" FLAT HEAD SCREWS (LL). Remember: Righty tighty. Lefty loosey. These surfaces should be even. J S H urf ID a D ce E w N i C th A M S A J S H urf ID a D ce E w N i C th A M S B Angled edge Angled edge LL BLACK 2-1/4" FLAT HEAD SCREW (8 used in this step) www.sauder.
Step 5 å Fasten one of the SHELF/BOTTOMS (D) to the ENDS (A and B). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Long edge with HIDDEN CAMS Finished edge B ith e w MS c a f A Sur EN C D HID J Long edge with HIDDEN CAMS D Sur f HID ace wi DEN th CA MS A ut itho w S e fac AM Sur EN C D HID J Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 6 å Fasten the other SHELF/BOTTOM (D) to the ENDS (A and B). Tighten four HIDDEN CAMS. Finished edge B A D Sur f HID ace wi DEN th CA MS Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 7 å Fasten the TOP (C) to the ENDS (A and B). Tighten four HIDDEN CAMS. å Fasten two METAL BRACKETS (BB) to the TOP (C). Use two BLACK 9/16" LARGE HEAD SCREWS (PP). (2 used) Long finished edge BB PP BLACK 9/16" LARGE HEAD SCREW (2 used in this step) Sur C fac ew ith hol es B A Maximum 210 degrees Arrow Minimum 190 degrees Page 12 409934 www.sauder.
Step 8 å Turn four BLACK 9/16" FLAT HEAD SCREWS (QQ) into the ENDS (A and B) until the shoulder of the SCREWS rest on the surface of the ENDS. å Slide the END MOLDINGS (P) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the SCREWS in the ENDS. P B P A QQ BLACK 9/16" FLAT HEAD SCREW (4 used in this step) Shoulder Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS. www.sauder.
Step 9 å Fasten the FRONT LEGS (H and I) to the ENDS (A and B). Tighten eight HIDDEN CAMS. Flat edge Flat edge I B H A 1 2 Page 14 409934 www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (E) to your unit using the NAILS (TT). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the SHELF/BOTTOM (D).
Step 11 å Fasten four HINGES (Y) and four HINGE SPACERS (Z) to the DOORS (F). Use eight SILVER 5/8" FLAT HEAD SCREWS (OO). Don't worry. It isn't Rome. This can be built in a day. OO SILVER 5/8" FLAT HEAD SCREW (8 used in this step) Y Z F F Y Z Page 16 409934 www.sauder.
Step 12 å å å Carefully stand your unit upright. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. Stop Mounting screw Fasten the DOOR (F) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them.
Step 13 å å å Refer to the enlarged diagram to identify the parts on the HINGES. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 14 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 2 Un fi su nish rfa ed ce D26 D981 D26 D27 D27 K K Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove Insert the DRAWER SIDES (D26 and D27) at an angle into the slot at each end of the DRAWER FRONT (K).
Step 15 å å Insert two SLIDE CAMS (JJ) into the DRAWER SIDES (D26 and D27). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the DRAWER RIGHT (35GC) and DRAWER LEFT (35GD) to the DRAWER SIDES (D26 and D27). Use four GOLD 5/16" FLAT HEAD SCREWS (SS) through holes #1 and #3.
Step 16 å Fasten the KNOBS (HH) to the DRAWER FRONT (K). Use three BLACK 1-1/8" MACHINE SCREWS (NN). NN BLACK 1-1/8" MACHINE SCREW (3 used for the KNOBS) K HH www.sauder.
Step 17 å With a hammer, gently tap four SHELF SNAPS (6R) into the holes in the ADJUSTABLE SHELF (G2). å Repeat this step for the other ADJUSTABLE SHELF (G2). (8 used) 6R ce fa ur S G2 ith w es ol h 6R Page 22 409934 www.sauder.
Step 18 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å Insert the METAL PINS (EE) into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (G2) onto the METAL PINS so the SHELF SNAPS are resting on the METAL PINS. Push on the SHELF until each METAL PIN "snaps" into the SHELF SNAP.
Step 19 å å Apply the WARNING LABEL (KK) to the left DOOR (F). You should be able to read the label when the DOOR is open. When the DOOR is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram. NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: -Place heaviest items in the lowest drawers.
Step 20 å We recommend using the SAFETY BRACKET (AA) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (PP) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (MM) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) MM AA BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) PP 10 lbs. 25 lbs. 25 lbs. 30 lbs. 20 lbs. www.sauder.
Step 21 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
409934 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 9 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer les PIEDS AVANT (H et I) aux EXTRÉMITÉS (A et B). Serrer huit EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer vingt et un EXCENTRIQUES ESCAMOTABLES (V2) dans les EXTRÉMITÉS (A et B), les TABLETTES/DESSOUS (D) et l’ENTRETOISE DE TIROIR (Q).
ÉTAPE 14 ÉTAPE 18 1 Insérer les CÔTÉS DE TIROIR (D26 et D27) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (K). Pour insérer le tiroir dans l'élément, abaisser le devant du tiroir et faire passer les roulettes situées sur le tiroir derrière les roulettes situées sur l'élément. Relever le devant du tiroir et l'enfiler dans l'élément. 2 Enfiler le FOND DE TIROIR (D981) dans les rainures des CÔTÉS DE TIROIR (D26 et D27) et du DEVANT DE TIROIR (K).
409934 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 9 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije las PATAS DELANTERAS (H e I) a los EXTREMOS (A y B). Apriete ocho EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje veintiún EXCÉNTRICOS ESCONDIDOS (V2) dentro de los EXTREMOS (A y B), de los ESTANTES/FONDOS (D) y de la RIOSTRA DEL CAJÓN (Q).
PASO 14 PASO 18 1 Inserte los LADOS DE CAJÓN (D26 y D27) en ángulo en el encaje en cada extremo de la CARA DE CAJÓN (K). Para insertar el cajón dentro de la unidad, incline la parte delantera del cajón hacia abajo y deje que los rodillos del cajón caigan detrás de los rodillos de la unidad. Levante la parte delantera del cajón y deslícelo dentro de la unidad. 2 Deslice el FONDO DE CAJÓN (D981) dentro de las ranuras de los LADOS DE CAJÓN (D26 y D27) y de la CARA DE CAJÓN (K).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
