sauder.com Smart stand for the idiot box. Panel TV Stand Shoal Creek Collection | 409795 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-24 Español pg 25-28 Lot # 373326 05/26/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-20 Hammer Français 21-24 Español 25-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. R RIGHT CABINET RAIL - 2 S V2 HIDDEN CAM - 30 W2 CAM DOWEL - 18 X2 Z SLIDE CAM - 4 BB KNOB - 4 CC METAL PIN - 8 FF WARNING LABEL - 1 LEFT CABINET RAIL - 2 T RIGHT DRAWER SLIDE - 2 U LEFT DRAWER SLIDE - 2 CAM SCREW - 12 LL FOOT CAP - 1 Y CAM COVER - 8 DD RUBBER SLEEVE - 8 MM FOOT BRACKET - 1 WARNING Never use this furniture with a TV that is too large or too heavy.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push thirty HIDDEN CAMS (V2) into the ENDS (A and B), UPRIGHT (C), BOTTOM (E2), and FIXED SHELVES (F). Then, insert a CAM DOWEL (W2) into eighteen HIDDEN CAMS. Do not tighten the HIDDEN CAMS in this step. Arrow W2 (18 used) E2 (30 used) V2 C F Do not insert CAM DOWELS into these edges.
Step 2 å Turn twelve CAM SCREWS (X2) into the LEGS (I and J). (12 used) X2 Remember: Righty tighty. Lefty loosey. I I J J Page 6 409795 www.sauder.
Step 3 å Turn four BLACK 9/16” FLAT HEAD SCREWS (II) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å Slide the END MOLDINGS (M72) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. These edges should be even. M72 S HI urfa DD ce EN wi CA tho M ut S A S HI urfa DD ce EN wi CA tho M ut S B M72 Shoulder These edges should be even.
Step 4 å Fasten the LEGS (I and J) to the ENDS (A and B). Tighten twelve HIDDEN CAMS. These surfaces should be even. Edge with CAM DOWELS I S HI urfa DD ce EN wi CA th M S A These surfaces should be even. J Angled edge I S HI urfa DD ce EN wi CA th M S B J Angled edge 1 Page 8 2 409795 www.sauder.
Step 5 å Fasten the CABINET RAILS (R and S) to the ENDS (A and B) and UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD SCREWS (JJ) through holes #1 and #3. å NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification.
Step 6 å Fasten a FIXED SHELF (F) to the LEFT END (B). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. J ith e w AMS c a f Sur DEN C D I H Finished edge B Sur HIDface w DEN ith CA MS F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 7 å Fasten the UPRIGHT (C) to the FIXED SHELF (F). Tighten two HIDDEN CAMS. å Fasten the remaining FIXED SHELF (F) to the UPRIGHT (C). Tighten two HIDDEN CAMS. Edge with CAM DOWELS Finished edge F Finished edge C ith e w AMS c a f Sur DEN C D HI Maximum 210 degrees Arrow F Sur HIDface w DEN ith CA MS Minimum 190 degrees www.sauder.
Step 8 å Fasten the RIGHT END (A) to the FIXED SHELF (F). Tighten two HIDDEN CAMS. Side Step: Make nachos. (Optional, but recommended.) F I A Maximum 210 degrees ut itho S w e fac AM Sur DEN C HID Arrow Minimum 190 degrees Page 12 409795 www.sauder.
Step 9 å Fasten the BOTTOM (E2) to the ENDS (A and B). Tighten four HIDDEN CAMS. å Fasten the BOTTOM (E2) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (GG). Finished edge B C Sur HIDface w DEN ith CA MS E2 A GG BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 10 å Fasten the TOP (D) to the ENDS (A and B) and UPRIGHT (C). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Su rfa ce wit hh ole s B D C A Unfinished edge Page 14 409795 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Make equal margins along all four edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (G) to your unit using the NAILS (KK). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 12 å Fasten the FOOT BRACKET (MM) to the BOTTOM (E2). Use three BLACK 9/16" LARGE HEAD SCREWS (OO). å å Slide the SUPPORT FEET (PP) onto the FOOT BRACKET (MM). å Push a FOOT CAP (LL) into the grooves of the SUPPORT FEET (PP). NOTE: Line up the groove in the FEET with the teeth on the BRACKET. E2 MM PP PP OO BLACK 9/16" LARGE HEAD SCREW (3 used in this step) LL Page 16 409795 www.sauder.
Step 13 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D10 D969 D10 K D11 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å D11 K Insert the DRAWER SIDES (D10 and D11) at an angle into the slot at each end of the RIGHT DRAWER FRONT (K)..
Step 14 å å Insert a SLIDE CAM (Z) into the DRAWER SIDES (D10 and D11). å NOTE: The DRAWER SLIDES are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Fasten two KNOBS (BB) to the RIGHT DRAWER FRONT (K). Use two BLACK 1-1/8" MACHINE SCREWS (HH). å Repeat this step for the left drawer. Fasten the DRAWER SLIDES (T and U) to the DRAWER SIDES (D10 and D11).
Step 15 å å Carefully stand your unit upright. å å NOTE: Be sure the RIGHT DRAWER FRONT (K) is on the right, and the LEFT DRAWER FRONT (L) is on the left. å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. To insert the drawers into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit.
Step 16 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Meuble téléviseur à écran plat 409795 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer les PIEDS (I et J) aux EXTRÉMITÉS (A et B). Serrer douze EXCENTRIQUES ESCAMOTABLES. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 9 ÉTAPE 12 Fixer le DESSOUS (E2) aux EXTRÉMITÉS (A et B). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Fixer le SUPPORT DE PIED (MM) au DESSOUS (E2). Utiliser trois VIS TÊTE LARGE 14 mm NOIRES (OO). Fixer le DESSOUS (E2) au MONTANT (C). Utiliser deux VIS TÊTE PLATE 48 mm NOIRES (GG). Faire glisser les PIEDS DE SUPPORT (PP) sur le SUPPORT DE PIED (MM). ÉTAPE 10 Fixer le DESSUS (D) aux EXTRÉMITÉS (A et B) et au MONTANT (C). Serrer six EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 14 ÉTAPE 16 Insérer une EXCENTRIQUE DE COULISSE (Z) dans les CÔTÉS DE TIROIR (D10 et D11). Pour ajuster les tiroirs, desserrer la VIS nº 3 dans les COULISSES un quart de tour et tourner ensuite la CAME dans le sens des aiguilles d'une montre ou dans le sens contraire. Noter que le tiroir monte ou descend lorsque l'on tourne la CAME. Plus la vis dans le trou oblong est haute, plus le devant de tiroir sera haut. Plus la vis est basse, plus le devant de tiroir sera bas.
Mueble Televisión para televisor de panel plano 409795 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga.
PASO 8 PASO 11 Fije el EXTREMO DERECHO (A) al PARAL (C). Apriete dos EXCÉNTRICOS ESCONDIDOS Precaución No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. PASO 9 Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (G) y colóquelo sobre la unidad. Fije el FONDO (E2) a los EXTREMOS (A y B). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Los márgenes a lo largo de los cuatro bordes del DORSO (G) deben estar uniformes.
PASO 13 PASO 15 Inserte los LADOS DE CAJÓN (D10 y D11) en ángulo dentro del encaje en cada extremo de la CARA DE CAJÓN DERECHO (K). Cuidadosamente ponga la unidad en posición vertical. Deslice un FONDO DE CAJÓN (D969) dentro de las ranuras de los LADOS DE CAJÓN (D10 y D11) y de la CARA DE CAJÓN DERECHA (K). Repita este paso para el cajón izquierdo. Utilice la CARA DE CAJÓN IZQUIERDO (L). Fije el DORSO DE CAJÓN (D72) a los LADOS DE CAJÓN (D10 y D11).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
