sauder.com Your holder for all things awesome. Highboy TV Stand Edge Water Collection | 409242 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 374229 06/02/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety Warranty Not actual size Short Screwdriver (provided) 29-30 31 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) W EXTENSION RAIL - 8 BB2 CAM SCREW - 11 HH RUBBER SLEEVE - 8 X CC EXTENSION SLIDE - 8 ANGLE BRACKET - 5 II Y PLASTIC FOOT - 1 JJ HIDDEN CAM - 41 FF KNOB - 8 DD SLIDE CAM - 8 CAM COVER - 8 Z2 WARNING LABEL - 1 AA2 CAM DOWEL - 30 GG METAL PIN - 16 4G METAL BRACKET - 2 WARNING Never use this furniture with a TV that is too large or too heavy.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push forty-one HIDDEN CAMS (Z2) into the ENDS (A and B), UPRIGHTS (C and D), TOP (E2), UPPER SHELF (F), and BRACES (H, I, and J). Then, insert the metal end of thirty CAM DOWELS (AA2) into the HIDDEN CAMS. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Turn six CAM SCREWS (BB2) into the LEGS (M3). å Fasten the FEET (V) to the LEGS (M3). Use two BLACK 1-7/8" PAN HEAD SCREWS (MM). Remember: Righty tighty. Lefty loosey. Fasten the LEGS (M3) to the ENDS (A and B). Tighten six HIDDEN CAMS. BB2 M3 M3 These surfaces should be even. These surfaces should be even. A S HI urfa DD ce EN wi CA th M S M3 V S HI urfa DD ce EN wi CA th M S B M3 MM BLACK 1-7/8" PAN HEAD SCREW (2 used in this step) V 1 Page 6 2 409242 www.sauder.
Step 3 å Separate the EXTENSION SLIDES (X) from the EXTENSION RAILS (W) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (W) to the ENDS (A and B) and SHORT UPRIGHTS (D). Use sixteen GOLD 5/16” FLAT HEAD SCREWS (PP). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END.
Step 4 å Fasten the SHELF MOLDINGS (U) to the UPPER SHELF (F) and FRONT BRACE (I). Tighten eight HIDDEN CAMS. Su rfa ce wi th HI DD EN CA M S U I U Su rfa ce wi th HI DD EN CA M S F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 8 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 409242 www.sauder.
Step 5 å å Turn five CAM SCREWS (BB2) into the STOP MOLDING (RR). å Fasten the LEFT END (B) and UPRIGHT (C) to the TOP (E2). Tighten four HIDDEN CAMS. Caution Fasten the TOP (E2) to the STOP MOLDING (RR). Tighten five HIDDEN CAMS. Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 6 å Fasten the UPPER SHELF (F) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the UPPER SHELF (F) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). U C B F Sur fac ew ith HID DEN CA MS LL BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Maximum 210 degrees Arrow Minimum 190 degrees Page 10 409242 www.sauder.
Step 7 å Fasten a SHORT UPRIGHT (D) to the UPPER SHELF (F). Tighten two HIDDEN CAMS. Finished edge D e fac Sur with EN D HID S M CA Maximum 210 degrees F Arrow Minimum 190 degrees www.sauder.
Step 8 å å Insert four METAL PINS (GG) into the BRACES (H and I). å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the LEFT END. å Fasten the BRACES (H and I) to the SHORT UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). Fasten the BRACES (H and I) to the LEFT END (B). Tighten two HIDDEN CAMS.
Step 9 å Fasten the other SHORT UPRIGHT (D) to the BRACES (H and I). Tighten two HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Finished edge I H D e fac Sur with EN D HID S M CA Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 10 å å Insert four METAL PINS (GG) into the BRACES (H and J). å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the LEFT END. å Fasten the BRACES (H and J) to the SHORT UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). Fasten the BRACES (H and J) to the LEFT END (B). Tighten two HIDDEN CAMS. These holes must be here.
Step 11 å Fasten the RIGHT END (A) to the TOP (E2), UPPER SHELF (F) and BRACES (H, I, and J). Tighten eight HIDDEN CAMS. Use the provided SHORT SCREWDRIVER. å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the RIGHT END. å Fasten two METAL BRACKETS (4G) to the LEGS (M3) and STOP MOLDING (RR). Use four BLACK 9/16" LARGE HEAD SCREWS (OO). å Fasten five ANGLE BRACKETS (CC) to the BOTTOM BRACE (J). Use five BLACK 9/16" LARGE HEAD SCREWS (OO).
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Make equal margins along all four edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (G) to your unit using the NAILS (QQ). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å Fasten the EXTENSION BLOCK (K) to the SHORT UPRIGHT (D). Use two BLACK 2-3/4" FLAT HEAD SCREWS (KK).
Step 13 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D968 D12 D12 D13 D13 O2 O2 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D12 and D13) at an angle into the slot at each end of the LEFT DRAWER FRONT (O2).
Step 14 å Insert the SLIDE CAMS (DD) into the large holes in the DRAWER SIDES (D12 and D13). å Fasten the EXTENSION SLIDES (X) to the DRAWER SIDES (D12 and D13). Use four GOLD 5/16" FLAT HEAD SCREWS (PP) through holes #1 and #3. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawers.
Step 15 å Fasten two KNOBS (FF) to the LEFT DRAWER FRONT (O2). Use two BLACK 7/8" MACHINE SCREWS (NN). å Repeat this step for the other drawers. NN BLACK 7/8" MACHINE SCREW (8 used in this step) O2 FF www.sauder.
Step 16 å å Carefully stand your unit upright. å To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. Pro Tip: Lift with your legs. And, you know, your arms. Push the RUBBER SLEEVES (HH) over the METAL PINS (GG).
Step 17 å å Push a CAM COVER (II) onto each visible HIDDEN CAM. å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. Apply the WARNING LABEL (JJ) to the TOP (E2). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. WARNING Never use this furniture with a TV that is too large or too heavy.
Step 18 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the cam clockwise or counterclockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawers this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREWS when finished with adjustments. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
409242 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES à cette étape. Fixer la TABLETTE SUPÉRIEURE (F) à l’EXTRÉMITÉ GAUCHE (B). Serrer deux EXCENTRIQUES ESCAMOTABLES. Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Fixer la TABLETTE SUPÉRIEURE (F) au MONTANT (C). Utiliser deux VIS NOIRES TÊTE PLATE 48 mm (LL).
ÉTAPE 12 ÉTAPE 15 Avec précaution, retourner l’élément sur ses chants avant. Déplier l’ARRIÈRE (G) et le placer sur l’élément. Fixer deux POIGNÉES (FF) au DEVANT GAUCHE DE TIROIR (O2). Utiliser deux VIS NOIRES À MÉTAUX 22 mm (NN). Veiller à avoir des marges égales le long des quatre chants de l’ARRIÈRE (G). Si besoin est, enfoncer sur les coins opposés de l’élément pour s’assurer d’être « d’équerre ». Répéter cette étape pour les autres tiroirs.
409242 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije un PARAL CORTO (D) al ESTANTE SUPERIOR (F). Apriete dos EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje cuarenta y uno EXCÉNTRICOS ESCONDIDOS (Z2) dentro de los EXTREMOS (A y B), los PARALES (C y D), el PANEL SUPER (E2), el ESTANTE SUPERIOR (F) y las RIOSTRAS (H, I y J).
PASO 12 PASO 16 Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (G) y colóquelo sobre la unidad. Cuidadosamente ponga la unidad en posición vertical. Empuje los MANGUITOS DE GOMA (HH) sobre las ESPIGAS DE METAL (GG). Inserte las ESPIGAS DE METAL dentro de los agujeros al nivel preferido de los EXTREMOS (A y B) y del PARAL (C). Coloque los ESTANTES AJUSTABLES (L) sobre las ESPIGAS DE METAL.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
