sauder.com Deep shelves for tall tales. Library with Doors Edge Water Collection | Model 409046 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 363879 07/14/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 409046 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) B LEFT END (1) C TOP (1) D SHELF/BOTTOM (2) E BACK (1) F DOOR (2) G ADJUSTABLE SHELF (2) H SMALL AJDUSTABLE SHELF (1) I LEG (2) J VALANCE (3) K FOOT (2) C J E G A G I B I D J H D K J F K F www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (L) into the large holes in the RIGHT END (A) and LEFT END (B). å Repeat this step for the SHELF/BOTTOMS (D). Scan this QR code or go to this address: http://qr.sauder.com/?ID=1190 to watch a video on how to assemble your unit.
Step 2 å Push ten HIDDEN CAMS (1F) into the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Arrow 1F A B Arrow (10 used) 1F Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 409046 www.sauder.
Step 3 å Turn ten CAM SCREWS (8F) into the LEGS (I). Remember: Righty tighty. Lefty loosey. (10 used) 8F I I www.sauder.
Step 4 å Fasten the LEGS (I) to the ENDS (A and B). Tighten ten HIDDEN CAMS. å Fasten the FEET (K) to the LEGS (I). Use two BLACK 1-5/8" PAN HEAD SCREWS (Y). 1 2 These surfaces should be even. I A B I K K Y BLACK 1-5/8" PAN HEAD SCREW (2 used for the FEET) Page 8 409046 www.sauder.
Step 5 å Fasten the SHELF/BOTTOMS (D) to the ENDS (A and B). Tighten eight TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 6 å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. Rounded edge C B A Page 10 409046 www.sauder.
Step 7 å Fasten nine METAL BRACKETS (Q) to the TOP (C) and SHELF/BOTTOMS (D). Use nine BLACK 9/16" LARGE HEAD SCREWS (AA). å NOTE: Be sure the BRACKETS are even with the edges of the SHELF/BOTTOMS. å Fasten the VALANCES (J) to the TOP (C) and SHELF/BOTTOMS (D). Use nine BLACK 9/16" LARGE HEAD SCREWS (AA). AA BLACK 9/16" LARGE HEAD SCREW (18 used in this step) Angled edge (9 used) Q J Angled edge C Angled edge J D J D www.sauder.
Step 8 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (E) to your unit using the NAILS (CC). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the SHELF/BOTTOM (D).
Step 9 å Fasten two HINGES (O) to each DOOR (F). Use eight BLACK 1/2" FLAT HEAD SCREWS (BB). BB BLACK 1/2" FLAT HEAD SCREW (8 used in this step) O F F O www.sauder.
Step 10 å å Carefully stand your unit upright. Pro Tip: Lift with your legs. And, you know, your arms. Push four RUBBER SLEEVES (W) over four METAL PINS (V). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the SMALL ADJUSTABLE SHELF (H) onto the METAL PINS. A H B V W Page 14 409046 (4 used) www.sauder.
Step 11 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten a DOOR (F) to the RIGHT END (A). Use the screws provided in the HINGES. See the next step for adjustments. å Fasten a KNOB (R) and BACKPLATE (S) to the DOOR (F). Use a BLACK 1-1/8" MACHINE SCREW (Z). å Peel the BUMPERS from the BUMPER CARD (T).
Step 12 å å Refer to the enlarged diagram to identify the parts on the HINGES. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed.
Step 13 å Push the remaining RUBBER SLEEVES (W) over the METAL PINS (V). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (G) onto the METAL PINS. å Push a CAM COVER (U) onto each visible HIDDEN CAM in the ENDS (A and B). G U (10 used) To cover HIDDEN CAMS G A B V W www.sauder.
Step 14 å å IMPORTANT: This unit must be positioned against a wall. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. We recommend using the SAFETY BRACKET (P) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (AA) into the top of the unit and a BLACK 1-7/8" PAN HEAD SCREW (X) into a stud in your wall.
Modèle 409046 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 REMARQUE : Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l’assemblage. Fixer le DESSUS (C) aux EXTRÉMITÉS (A et B). Serrer quatre FIXATIONS TWIST-LOCK®. Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Pour commencer l’assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (L) dans les gros trous de l’EXTRÉMITÉ DROITE (A) et l’EXTRÉMITÉ GAUCHE (B). Répéter cette étape pour les pièces TABLETTE/DESSOUS (D).
ÉTAPE 11 ÉTAPE 13 Avant de fixer la PORTE à l’unité, s’assurer que la vis de montage se trouve contre les butées comme l’indique le schéma de droite. Si ce n’est pas le cas, desserrer la vis de montage pour la faire glisser contre les butées. Serrer ensuite la vis de montage. La porte peut être ajustée à l’étape suivante. Enfoncer les autres MANCHONS EN CAOUTCHOUC (W) sur les GOUPILLES EN MÉTAL (V). Insérer les GOUPILLES EN MÉTAL dans les trous choisis dans les EXTRÉMITÉS (A et B).
Modelo 409046 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 NOTA: No apriete los SUJETADORES TWIST-LOCK® por ahora. Fije el PANEL SUPERIOR (C) a los EXTREMOS (A y B). Apriete cuatro SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (L) dentro de los agujeros grandes del EXTREMO DERECHO (A) y del EXTREMO IZQUIERDO (B). Repita este paso para las partes ESTANTE/FONDO (D).
PASO 11 PASO 13 Antes de ajustar la PUERTA en su unidad, asegúrese de que el tornillo de montaje esté contra los topes, tal como se muestra en el diagrama de la derecha. Si no lo está, afloje el tornillo de montaje para que se deslice contra los topes. Luego apriete el tornillo de montaje. Los ajustes de la puerta se harán en el siguiente paso. Empuje los MANGUITOS DE GOMA (W) sobre las ESPIGAS DE METAL (V). Inserte las ESPIGAS DE METAL dentro de los agujeros al nivel preferido de los EXTREMOS (A y B).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
