sauder.com Get all organized and stuff. Lateral File Edge Water Collection | 409044 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 385923 10/26/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification Assembly Steps No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size 31 Part Identification å Page 2 While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification C A2 E F2 D B2 L K F2 D225 D243 D928 L D225 D243 G D225 D243 D928 D225 D243 G www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) M EXTENSION RAIL - 4 R METAL BRACKET - 3 S N DRAWER ACTUATOR - 2 EXTENSION SLIDE - 4 T CABINET ACTUATOR - 2 U FILE BRACKET - 4 V KNOB - 4 W FILE GLIDE - 4 X FILE BAR - 4 Y FILE ROD - 4 Z INTERLOCK TRACK - 1 1F 2F CAM DOWEL - 12 8F HIDDEN CAM - 18 Page 4 409044 CAM SCREW - 6 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 16S BLACK 1-7/8" PAN HEAD SCREW - 2 BB CC BLACK 1-1/8" MACHINE SCREW - 4 DD BLACK 7/8" LARGE HEAD SCREW - 8 EE FF BLACK 9/16" LARGE HEAD SCREW - 6 BLACK 1-1/4" FLAT HEAD SCREW - 16 BROWN 7/16" LARGE HEAD SCREW - 8 GG GOLD 5/16" FLAT HEAD SCREW - 16 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1302 to watch a video on how to assemble your unit. Push eighteen HIDDEN CAMS (1F) into the ENDS (A2 and B2), BOTTOM (D), and BACK (E).
Step 2 å Insert two CABINET ACTUATORS (T) into the holes shown in the RIGHT END (A2). T This pin must insert into the location holes in the RIGHT END (A2). T A2 www.sauder.
Cut out this rectangle to use as a "spacer" 2-1/2" Step 3 å Diagram 1. Cut out and use the “spacer” at the top of this page to measure 2-1/2” from one end of the INTERLOCK TRACK (Z). Position the INTERLOCK TRACK as shown. å å å ACTUATOR / TRACK ATTACHMENT: å Diagram 4. Repeat the ACTUATOR / TRACK ATTACHMENT for the next CABINET ACTUATOR while holding the previously completed CABINET ACTUATOR in its location hole. Repeat these steps until all ACTUATORS have been attached.
Step 4 å å Turn six CAM SCREWS (8F) into the LEGS (F2). å Fasten the FEET (L) to the LEGS (F2). Use two BLACK 1-7/8" PAN HEAD SCREWS (16S). Fasten the LEGS (F2) to the ENDS (A2 and B2). Tighten six HIDDEN CAMS. 8F (6 used) View after the FOOT is fastened F2 F2 These surfaces must be even. F2 These surfaces must be even. A2 S HI urfa DD ce EN wi CA th M S L S HI urfa DD ce EN wi CA th M S B2 F2 16S BLACK 1-7/8" PAN HEAD SCREW (2 used in this step) L 1 www.sauder.
Step 5 å Insert the INTERLOCK TRACK (Z) with CABINET ACTUATORS (T) into the groove in the RIGHT END (A2) exactly as shown. å Separate the EXTENSION SLIDES (N) from the EXTENSION RAILS (M) as shown in the upper diagram. Be prepared, the parts are greasy. å Fasten two EXTENSION RAILS (M) to each END (A2 and B2). Use eight GOLD 5/16” FLAT HEAD SCREWS (GG). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram.
Step 6 å Fasten the LEFT END (B2) to the BACK (E). Tighten two HIDDEN CAMS. e fac Sur withDEN HID S M CA F2 These edges must be even. B2 ce rfa Su th wi EN DD HI S M CA E Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 7 å Fasten the BOTTOM (D) to the LEFT END (B2). Tighten two HIDDEN CAMS. å Fasten the RIGHT END (A2) to the BOTTOM (D) and BACK (E). Tighten four HIDDEN CAMS. B2 These holes must be here. Sur fac ew ith HID DEN CA MS D E ut itho S w e fac AM Sur DEN C HID A2 Maximum 210 degrees Arrow Minimum 190 degrees Page 12 409044 www.sauder.
Step 8 å Fasten three METAL BRACKETS (R) to the BOTTOM (D). Use three BLACK 9/16” LARGE HEAD SCREWS (EE). å NOTE: Be sure the BRACKETS are even with the edges of the BOTTOM. å Fasten the BOTTOM MOLDING (K) to the METAL BRACKETS (R). Use three BLACK 9/16” LARGE HEAD SCREWS (EE). Curved edge K D R EE BLACK 9/16" LARGE HEAD SCREW (6 used in this step) www.sauder.
Step 9 å å Carefully stand your unit upright. Fasten the TOP (C) to the ENDS (A2 and B2). Tighten four HIDDEN CAMS. su rfa ce C Fi ni sh ed Rounded edge A2 B2 Maximum 210 degrees Arrow Minimum 190 degrees Page 14 409044 www.sauder.
Step 10 å Fasten two DRAWER SIDES (D225) to one of the DRAWER BOX FRONTS (D243). Use four BLACK 1-1/4” FLAT HEAD SCREWS (BB). å Repeat this step for the other drawer. D225 D243 D225 Be sure the grooves in each part line up with each other on the inside of the drawer. BB BLACK 1-1/4" FLAT HEAD SCREW (8 used in this step) www.sauder.
Step 11 å Slide a DRAWER BOTTOM (D928) into the grooves in the DRAWER SIDES (D225). å Fasten a DRAWER BOX FRONT (D243) to the DRAWER SIDES (D225). Use four BLACK 1-1/4” FLAT HEAD SCREWS (BB). å Repeat this step for the other drawer. D225 D243 ed h is n Fi D225 e ac rf su D243 D928 BB BLACK 1-1/4" FLAT HEAD SCREW (8 used in this step) Page 16 409044 www.sauder.
Step 12 å Fasten a DRAWER FRONT (G) to one of the DRAWER BOX FRONTS (D243). Use four BLACK 7/8” LARGE HEAD SCREWS (DD). å Fasten two KNOBS (V) to the DRAWER FRONT (G). Use two BLACK 1-1/8” MACHINE SCREW (CC). å NOTE: The hole on back surface of the DRAWER FRONT must be close to the bottom edge. å Repeat this step for the other drawer.
Step 13 å Stand one of the drawers upright onto the RIGHT DRAWER SIDE (D225). å Fasten one of the EXTENSION SLIDES (N) through holes #2 and #4 to the LEFT DRAWER SIDE (D225). Use two GOLD 5/16” FLAT HEAD SCREWS (GG). GG GOLD 5/16" FLAT HEAD SCREW (4 used in this step) 3 4 2 Open end 1 N D225 D225 Page 18 409044 www.sauder.
Step 14 å å å Flip the drawer over onto the left DRAWER SIDE (D225). GG Diagram 1. Insert the tabs on a DRAWER ACTUATOR (S) into the slots in a EXTENSION SLIDE (N). You may need to insert one tab first, then the other. GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Diagram 2. Visually check that the DRAWER ACTUATOR (S) is seated in the EXTENSION SLIDE (N). å Diagram 3. If the DRAWER ACTUATOR is not seated, use your hammer to gently tap the SLIDE until the tabs are properly seated in the slots.
Step 15 å Fasten two FILE BRACKETS (U) to the DRAWER BOX FRONTS (D243). Use four BROWN 7/16” LARGE HEAD SCREWS (FF). å Repeat this step for the other drawer. FF BROWN 7/16" LARGE HEAD SCREW (8 used in this step) U U D243 Page 20 409044 www.sauder.
Step 16 å å Push a FILE GLIDE (W) onto the RIGHT DRAWER SIDE (D225). å Slide another FILE GLIDE (W) onto the other end of the FILE RODS (Y), then press this FILE GLIDE over the LEFT DRAWER SIDE (D225). å Repeat this step for the other drawer. Slide the FILE RODS (Y) through a FILE BAR (X), through the holes in the FILE BRACKETS (U), through another FILE BAR (X), and into the FILE GLIDE (W) on the RIGHT DRAWER SIDE (I). Y W U D225 X X W D225 www.sauder.
Step 17 å To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. å NOTE: The DRAWER FRONTS may need adjustments. To adjust the DRAWER FRONTS, loosen the SCREWS in the DRAWER FRONTS. Make adjustments and tighten the SCREWS.
unit number Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Enfoncer le RAIL DE VERROUILLAGE (Z) avec les ACTIONNEURS D’ÉLÉMENT (T) dans la rainure de l’EXTRÉMITÉ DROITE (A2) exactement comme l’indique le schéma. Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Enfoncer dix-huit EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2), le DESSOUS (D) et l’ARRIÈRE (E).
ÉTAPE 10 ÉTAPE 15 Fixer deux CÔTÉS DE TIROIR (D225) sur l’un des DEVANTS DE CAISSON DU TIROIR (D243). Utiliser quatre VIS NOIRES TÊTE PLATE 32 mm (BB). Fixer deux CONSOLES POUR DOSSIERS (U) aux DEVANTS DE CAISSON DE TIROIR (D243). Utiliser quatre VIS MARRON TÊTE LARGE 11 mm (FF). Répéter cette étape pour l’autre tiroir. Répéter cette étape pour l’autre tiroir. ÉTAPE 11 ÉTAPE 16 Enfiler un FOND DE TIROIR (D928) dans les rainures des CÔTÉS DE TIROIR (D225).
409044 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Clave el CARRIL DE UNIÓN (Z) con ACTUADORES DE GABINETE (T) dentro de la ranura del EXTREMO DERECHO (A2) exactamente como se muestra. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A2 y B2), el FONDO (D) y el DORSO (E).
PASO 10 PASO 15 Fije dos LADOS DE CAJÓN (D225) a uno de los FRENTES DE CAJÓN (D243). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 32 mm (BB). Fije dos MÉNSULAS DE ARCHIVERO (U) a los FRENTES DE CAJÓN (D243). Utilice cuatro TORNILLOS MARRONES DE CABEZA GRANDE de 11 mm (FF). Repita este paso para el otro cajón. Repita este paso para el otro cajón. PASO 11 PASO 16 Deslice el FONDO DE CAJÓN (D928) dentro de las ranuras de los LADOS DE CAJÓN (D225).
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading drawers. Place the heavier items in the lower drawer.
PRECAUCIÓN Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones sobrecargados. • Riesgo de lesiones. • La caída de mobiliario inestable. • Los cajones sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones. • Para cargar los cajones trabaje desde abajo hacia arriba.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
