sauder.com For all your newfangled gadgetry. Computer Desk Beginnnings Collection | 408726 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 372058 05/06/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 408726 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1093 to watch a video on how to assemble your unit. Push ten HIDDEN CAMS (S2) into the ENDS (A2, B, and C), UPRIGHT (D3), SMALL UPRIGHT (E3), and SMALL BACK (K2).
Step 2 å Fasten the CABINET RIGHT (30AA) and CABINET LET (30AB) to the LEFT END (B) and UPRIGHT (D3). Use four GOLD 5/16" FLAT HEAD SCREWS (II). Remember: Righty tighty. Lefty loosey. Roller end Finished edge D3 B Roller end Finished edge II GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 6 408726 www.sauder.
Step 3 å Fasten the SMALL UPRIGHT (E3) to the SMALL BACK (K2). Use a BLACK 1-15/16" FLAT HEAD SCREW (113S). Finished edge Finished edge K2 Sur HIDface w DEN itho CA ut M ith e w AM c a f Sur DEN C HID E3 113S BLACK 1-15/16" FLAT HEAD SCREW (1 used in this step) www.sauder.
Step 4 å Fasten the SMALL UPRIGHT (E3) and SMALL BACK (K2) to the TOP (F2). Tighten two HIDDEN CAMS. Sur HIDface w DEN ith CA M E3 K2 F2 Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 8 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 408726 www.sauder.
Step 5 å Fasten the DESK TOP (G3) to the SMALL UPRIGHT (E3) and SMALL BACK (K2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Long finished edge 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) ed h is fin n U G3 e ac rf su For support, place packing foam and magazines here. K2 www.sauder.
Step 6 å å Carefully turn your unit onto its front edges. Fasten the LEFT END (B) and UPRIGHT (D3) to the DESK TOP (G3). Tighten four HIDDEN CAMS. Unfinished edge Unfinished edge G3 B D3 Maximum 210 degrees Arrow Minimum 190 degrees Page 10 408726 www.sauder.
Step 7 å Fasten the MODESTY PANEL (L) to the LEFT END (B) and UPRIGHT (D3). Use four BLACK 1-7/8" FLAT HEAD SCREWS (DD). DD U n fin is h ed su rf ac e Notch L B D3 DD BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 8 å Fasten the RIGHT END (A2) to the TOP (F2). Tighten two HIDDEN CAMS. å Fasten the SHELF (HH3) to the RIGHT END (A2) and UPRIGHT (D3). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Fasten a MAGNETIC CATCH (V2) to the SHELF (HH3). Use a BLACK 1-1/8" PAN HEAD SCREW (KK).
Step 9 å Fasten the LOWER RIGHT END (C) to the SHELF (HH3). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (I) to LOWER RIGHT END (C) and UPRIGHT (D3). Use four BLACK 1-7/8" FLAT HEAD SCREWS (DD). D3 Unfinished edge HH3 C Maximum 210 degrees I Arrow Minimum 190 degrees DD BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 10 å Make equal margins along all four edges of the BACK (J). Push on opposite corners of your unit if needed to make it “square”. å Fasten the BACK (J) to your unit using the NAILS (JJ). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. J JJ NAIL (12 used in this step) Page 14 408726 www.sauder.
Step 11 å Fasten a PIVOT HINGE (X) to the DOOR (N). Use one BROWN 7/16" LARGE HEAD SCREW (HH). å Fasten a STRIKE PLATE (W) to the DOOR (N). Use one BLACK 1/2" FLAT HEAD SCREW (GG). å NOTE: The surface of the STRIKE PLATE with “SAUDER” should be facing up. Now might be a good time to refresh your drink. IMPORTANT: ONLY fasten one HINGE to the DOOR in this step. HH BROWN 7/16" LARGE HEAD SCREW (1 used for the PIVOT HINGE) N X W GG BLACK 1/2" FLAT HEAD SCREW (1 used in this step) www.sauder.
Step 12 å å Carefully stand your unit upright. å 2. Insert the PIVOT HINGE, which is fastened to the DOOR (N), into the hole in the SHELF (HH3). You will need to tilt your DOOR slightly. å 3. Now, tip the DOOR in and fasten the free HINGE to the DOOR. Use a BROWN 7/16" LARGE HEAD SCREW (HH) å Fasten the HANDLE (Z) to the DOOR (N). Use two BLACK 7/8" FLAT HEAD SCREWS (FF). å NOTE: To make adjustments to the DOOR, loosen the SCREW in the HINGE, make needed adjustments, and tighten the SCREW. 1.
Step 13 å å å Fasten the DRAWER RIGHT (30AC) and DRAWER LEFT (30AD) to the KEYBOARD SHELF (M). Use four BROWN 1" FLAT HEAD SCREWS (EE). Almost time to celebrate! With a nap. Turn the CORD CLIP (AA) into the KEYBOARD SHELF (M). NOTE: The CORD CLIP is used to hold your keyboard cord against the KEYBOARD SHELF. Roller end AA ed h is n Fi e ac rf su Roller end M EE BROWN 1" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 14 å To insert the KEYBOARD SHELF (M) into your unit, tip the front of the shelf down and drop the rollers on the shelf behind the rollers on the unit. Lift the front of the shelf up and slide it into the unit. å å Push a CAM COVER (BB) onto each HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
408726 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Avec précaution, retourner l’élément sur ses chants avant. Enfoncer dix EXCENTRIQUES ESCAMOTABLES (S2) dans les EXTRÉMITÉS (A2, B et C), le MONTANT (D3), le PETIT MONTANT (E3) et le PETIT ARRIÈRE (K2). Ensuite, insérer une CHEVILLE D’EXCENTRIQUE (T2) dans chaque EXCENTRIQUE ESCAMOTABLE. Fixer l’EXTRÉMITÉ GAUCHE (B) et MONTANT (D3) au DESSUS DE BUREAU (G3).
ÉTAPE 10 ÉTAPE 13 Veiller à avoir des marges égales lelong des quatre chants de l’ARRIÈRE (J). Si besoin est, enfoncer sur les coins opposés de l’élément pour s’assurer d’être « d’équerre ». Fixer le TIROIR DROIT (30AC) et le TIROIR GAUCHE (30AD) à la TABLETTE DE CLAVIER (M). Utiliser quatre VIS MARRON TÊTE PLATE 25 mm (EE). Fixer l’ARRIÈRE (J) à l’élément en utilisant les CLOUS (JJ). Insérer le CLIP DE CORDON (AA) dans la TABLETTE DE CLAVIER (M).
408726 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Empuje diez EXCÉNTRICOS ESCONDIDOS (S2) dentro de los EXTREMOS (A2, B y C), el PARAL (D3), el PARAL PEQUEÑO (E3) y el DORSO PEQUEÑO (K2). A continuación, inserte un PASADOR DE EXCÉNTRICO (T2) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 10 PASO 13 Fije el DORSO (J) de manera que los márgenes son iguales a lo largo de los cuatro bordes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla “cuadrada.” Fije la CAJÓN DERECHO (30AC) y la CAJÓN IZQUIERDO (30AD) al ESTANTE DE TECLADO (M). Utilice cuatro TORNILLOS MARRONES DE CABEZA PERDIDA de 25 mm (EE). Fije el DORSO (J) a la unidad utilizando los CLAVOS (JJ). Atornille la GRAPA DE CABLE (AA) dentro del ESTANTE DE TECLADO (M).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
