sauder.com For all your newfangled gadgetry. Computer Desk with Hutch Harbor View Collection | Model 158034 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 Assembly Steps 6-36 Hammer Français 37-40 Español 41-44 Safety 45-46 Warranty Not actual size Skip the power trip. This time. 47 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification FF I EE C Q GG Q M R O II G R L H2 D A P II T E J N K F JJ D109 D24 D716 B D25 HH Z D78 S D87 D708 D88 U www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1536 to watch a video on how to assemble your unit. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (UU) into the large holes in the ENDS (A and B).
Step 2 å Slide the DESK END MOLDING* (HH) onto the notched edge of the LEFT END (B). å Slide the HUTCH END MOLDINGS* (II) onto the notched edges of the HUTCH ENDS (C and D). å *U.S. Patent No. 5,499,886 Slide the DESK END MOLDING (HH) onto the notched edge. HH S TW urfa FA IS ce ST T-L wit EN O h ER CK S ® B Slide the HUTCH END MOLDINGS (II) onto the notched edges. II Su TW rfa FA IS ce ST T-L wit EN OC h ER K® S D www.sauder.
Step 3 å Fasten the ANGLE BRACKET (DDD) to the LEFT END (B) and DESK END MOLDING (HH). Use two BLACK 9/16" LARGE HEAD SCREWS (PPP). å NOTE: There is no pre-drilled hole in the END MOLDING. The SCREW will tighten into the groove. å Fasten the RAIL BRACKETS (ZZ) to the LEFT END (B). Use four BLACK 9/16" LARGE HEAD SCREWS (PPP). Remember: Righty tighty. Lefty loosey.
Step 4 å Fasten the CABINET RIGHT (35AW) to the LEFT UPRIGHT (F) and a CABINET LEFT (35AX) to the LEFT END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (RRR). RRR GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end Finished edge F S TW urfa FA IS ce ST T-L wit EN O ho ER CK ut S ® Roller end HH www.sauder.
Step 5 å Fasten the CABINET RIGHTS (40CA) to the RIGHT END (A) and CABINET LEFTS (40CB) to the RIGHT UPRIGHT (E). Use eight GOLD 5/16" FLAT HEAD SCREWS (RRR) through holes #1 and #3. RRR Roller end GOLD 5/16" FLAT HEAD SCREW (8 used in this step) 1 2 3 1 4 2 Finished edge 3 4 A 4 S TW urfa FA IS ce ST T-L wit EN O h ER CK S ® 3 2 4 1 3 2 E Roller end S TW urfa FA IS ce ST T-L wit EN O h ER CK S ® 1 Finished edge Page 10 158034 www.sauder.
Step 6 å Separate the EXTENSION SLIDES (TT) from the EXTENSION RAILS (SS) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (SS) to the RIGHT END (A) and RIGHT UPRIGHT (E). Use four GOLD 5/16” FLAT HEAD SCREWS (RRR). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END and UPRIGHT.
Step 7 å Tap two MOLDING CONNECTORS (EEE) into the notches in the MOLDINGS (EE, FF, and GG). Use your hammer to tap the MOLDING CONNECTORS (EEE) into the notches in the MOLDINGS. Flat end Flat end EEE GG EEE EE FF Page 12 158034 www.sauder.
Step 8 å Fasten the MOLDINGS (EE, FF, and GG) to the HUTCH TOP (I). Use eight BLACK 1-5/8" PAN HEAD SCREWS (LLL). å NOTE: Do not overtighten the SCREWS into the TOP. LLL BLACK 1-5/8" PAN HEAD SCREW (8 used in this step) GG EE Finished surface ce fa ur S I ith w es ol h FF Unfinished edge www.sauder.
Step 9 å Fasten the LEFT HUTCH END (D) to the LEFT MOLDING (GG) on the HUTCH TOP (I). Tighten two TWIST-LOCK® FASTENERS. å Insert eight METAL PINS (GGG) into the SMALL PINNED UPRIGHTS (R). å Insert the METAL PINS (GGG) in one end of the SMALL PINNED UPRIGHTS (R) into the holes in the HUTCH TOP (I). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1.
Step 10 å å Fasten the LARGE HUTCH SHELF (L) to the HUTCH LEFT END (D). Tighten two TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. NOTE: Be sure the METAL PINS in the SMALL PINNED UPRIGHTS (R) insert into the holes in the LARGE HUTCH SHELF (L). Finished edge R L D www.sauder.
Step 11 å Fasten the HUTCH UPRIGHT (G) to the HUTCH TOP (I) and LARGE HUTCH SHELF (L). Tighten four TWIST-LOCK® FASTENERS. å å Insert eight METAL PINS (GGG) into the LARGE PINNED UPRIGHTS (Q). Insert the METAL PINS (GGG) in one end of the LARGE PINNED UPRIGHTS (Q) into the holes in the HUTCH TOP (I). Finished edge L G Q I Q GGG (8 used) Page 16 158034 www.sauder.
Step 12 å Fasten the SMALL HUTCH SHELF (M) to the HUTCH UPRIGHT (G). Tighten two TWIST-LOCK® FASTENERS. å NOTE: Be sure the METAL PINS in the LARGE PINNED UPRIGHTS (Q) insert into the holes in the SMALL HUTCH SHELF (M). å Fasten the RIGHT HUTCH END (C) to the RIGHT MOLDING (FF) on the HUTCH TOP (I) and SMALL HUTCH SHELF (M). Tighten four TWIST-LOCK® FASTENERS. Finished edge I Q G M Sur f TW ace wi IS th FAS T-LO TEN CK® ERS Q FF ut itho® w e fac LOCK r u S IST RS TW TENE FAS www.sauder.
Step 13 å Fasten the DESK TOP (H2) to the HUTCH ENDS (C and D) and HUTCH UPRIGHT (G). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). Meet Part (H2). This component has been engineered to be lighter, stronger, faster… well ok. Not technically faster. But definitely makes for a sturdier Computer Desk with Hutch that’s easier to assemble and friendlier to the environment. D Rounded edge H2 G Sur mo face w re h ith ole s C 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Page 18 158034 www.
Step 14 å å Insert the LONG METAL PIN (FFF) into the LEFT END (B). å NOTE: Be sure the LONG METAL PIN in the LEFT END inserts into the hole in the DESK TOP. Fasten the LEFT END (B) to the DESK TOP (H2). Tighten two TWIST-LOCK® FASTENERS. FFF HH B H2 ith e w CK® c a f SurIST-LORS TW TENE FAS www.sauder.
Step 15 å Fasten the SHELF (K) to the MODESTY PANEL (J). Use three BLACK 1-7/8" FLAT HEAD SCREWS (UUU). å å Insert a METAL PIN (GGG) into the SHELF (K). å NOTE: Be sure the METAL PIN in the SHELF and the TWIST-LOCK® FASTENERS in the MODESTY PANEL insert into the holes in the LEFT END (B). You will not tighten the TWIST-LOCK® FASTENERS in the MODESTY PANEL until step 20. GGG Fasten the SHELF (K) to the LEFT END (B). Tighten a TWIST-LOCK® FASTENER.
Step 16 å Fasten the LEFT UPRIGHT (F) to the DESK TOP (H2). Tighten two TWIST-LOCK® FASTENERS. å Fasten the LEFT UPRIGHT (F) to the MODESTY PANEL (J) and SHELF (K). Use four BLACK 1-7/8" FLAT HEAD SCREWS (UUU). Finished edge J K F withK® e c fa C SurIST-LORS TW TENE FAS H2 UUU BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 17 å Fasten the RIGHT UPRIGHT (E) to the DESK TOP (H2). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (N) to the LEFT UPRIGHT (F). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (N) to the RIGHT UPRIGHT (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (UUU). These holes must be here. Finished edge F E H2 N Sur f TW ace wi IS th FAS T-LO TEN CK® ERS Surface with TWIST-LOCK® FASTENERS UUU BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 22 158034 www.sauder.
Step 18 å Fasten the RIGHT END (A) to the DESK TOP (H2) and BOTTOM (N). Tighten four TWIST-LOCK® FASTENERS. Finished edge H2 A N www.sauder.
Step 19 å Fasten four ANGLE BRACKETS (DDD) to the RIGHT END (A), LEFT UPRIGHT (F), and BOTTOM (N). Use four BLACK 9/16" LARGE HEAD SCREWS (PPP). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the END, UPRIGHT, and BOTTOM. å Fasten the BASE (JJ) to the RIGHT END (A), LEFT UPRIGHT (F), and BOTTOM (N). Use four BLACK 9/16" LARGE HEAD SCREWS (PPP). JJ A N F DDD DDD DDD PPP BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Page 24 158034 www.sauder.
Step 20 å Carefully turn your unit over onto its front edges. Unfold the LARGE BACK (O) and lay it over your unit. å Tighten the TWIST-LOCK® FASTENERS in the MODESTY PANEL (J). å Make equal margins along all four edges of the LARGE BACK (O). Push on opposite corners of your unit if needed to make it "square". å å Fasten the LARGE BACK (O) to your unit using NAILS (SSS). å å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 21 å Fasten two HINGES (VV) to the DOOR (S). Use four BLACK 1/2" FLAT HEAD SCREWS (QQQ). S QQQ BLACK 1/2" FLAT HEAD SCREW (4 used in this step) VV Page 26 158034 www.sauder.
Step 22 å å Carefully stand your unit upright. å Fasten the DOOR (S) to the RIGHT UPRIGHT (E) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å Fasten the KNOB SET (CCC) to the DOOR (S). Use a SILVER 1-1/4" MACHINE SCREW (MMM). å Peel the FELT DISC from the FELT DISC CARD (JJJ). Stick the FELT DISCS on the DOOR where they come in contact with the LEFT UPRIGHT (F). å See the next step for DOOR adjustments.
Step 23 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOOR may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOOR from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOOR up and down (vertical), loosen both vertical adjustment screws. Move the DOOR up or down to the desired location. Tighten the screws after making adjustments.
Step 24 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D708 D87 D87 D88 D88 U U Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D88 and D87) at an angle into the slot at each end of the DRAWER FRONT (U).
Step 25 å å Insert a SLIDE CAM (TTT) into the LARGE DRAWER SIDES (D87 and D88). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the EXTENSION SLIDES (TT) to the DRAWER SIDES (D87 and D88). Use four GOLD 5/16" FLAT HEAD SCREWS (RRR) through holes #1 and #4.
Step 26 å å å Push a FILE GLIDE (6B) onto the LARGE RIGHT DRAWER SIDE (D87). Slide the FILE RODS (YY) into the FILE GLIDE (6B) on the LARGE RIGHT DRAWER SIDE. Slide another FILE GLIDE (6B) onto the other end of the FILE RODS (YY), then press this FILE GLIDE over the LARGE LEFT DRAWER SIDE (D88). Insert the FILE RODS into the holes of your choice in the FILE GLIDES, depending on your file sizes. 6B YY YY D88 6B D87 www.sauder.
Step 27 å å Insert a SLIDE CAM (TTT) into the DRAWER SIDES (D24 and D25). å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten a DRAWER RIGHT (40CC) and a DRAWER LEFT (40CD) to the DRAWER SIDES (D24 and D25). Use four GOLD 5/16" FLAT HEAD SCREWS (RRR) through holes #2 and #4. Repeat this step for the remaining small drawer.
Step 28 å Fasten the DRAWER RIGHT (35AY) and the DRAWER LEFT (35AZ) to the KEYBOARD SHELF (T). Use four BROWN 1" FLAT HEAD SCREWS (NNN). å å Turn the CORD CLIP (HHH) into the KEYBOARD SHELF (T). NOTE: The CORD CLIP is used to hold your keyboard cord against the KEYBOARD SHELF. Roller end HHH ed h is n Fi T Roller end e ac rf su Finished edge NNN BROWN 1" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 29 å å To insert the large drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. Almost time to celebrate! With a nap. To insert the small drawers into your unit, tip the fronts of the drawers down and drop the rollers on the drawers behind the rollers on the unit.
Step 30 å Fasten the PULLS (BBB) to the DRAWER FRONTS (U and Z). Use six SILVER 5/8" MACHINE SCREWS (OOO). å Insert four HOLE PLUGS (III) into the holes in the FRONT MOLDING (EE). EE 15 lbs. 7 lbs. III (4 used) 7 lbs. 75 lbs. 25 lbs. 10 lbs. Z 10 lbs. Z N 40 lbs. U OOO 35 lbs. BBB SILVER 5/8" MACHINE SCREW (6 used for the PULLS) www.sauder.
Step 31 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 158034 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Enfoncer deux CONNECTEURS DE MOULURE (EEE) dans les crans des MOULURES (EE, FF et GG). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (UU) dans les gros trous des EXTRÉMITÉS (A et B).
ÉTAPE 12 ÉTAPE 18 Fixer la PETITE TABLETTE DE SURMEUBLE (M) au MONTANT DE SURMEUBLE (G). Serrer deux FIXATIONS TWIST-LOCK®. Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS DE BUREAU (H2) et au DESSOUS (N). Serrer quatre FIXATIONS TWIST-LOCK®. REMARQUE : S’assurer d’insérer les GOUPILLES EN MÉTAL dans les GRANDS MONTANTS GOUPILLÉS (Q) dans les trous de la PETITE TABLETTE DE SURMEUBLE (M).
ÉTAPE 23 ÉTAPE 27 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Insérer une EXCENTRIQUE DE COULISSE (TTT) dans les CÔTÉS DE TIROIR (D24 et D25). Il faut peut-être ajuster la PORTE. Suivre les indications ci-dessous pour ajuster. RÉGLAGES DES PORTES : Pour ajuster les PORTES latéralement (horizontalement), tourner la vis de réglage vers l'intérieur ou vers l'extérieur. Pour ajuster la PORTE de haut en bas (verticalement), desserrer les deux vis de réglage.
Escritorio de Computadora con Organizador Modelo 158034 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ligeramente clave dos CONECTORES DE MOLDURA (EEE) dentro de las muescas de las MOLDURAS (EE, FF y GG). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (UU) dentro de los agujeros grandes de los EXTREMOS (A y B).
PASO 12 PASO 18 Fije el ESTANTE PEQUEÑO DE ORGANIZADOR (M) al PARAL DE ORGANIZADOR (G). Apriete dos SUJETADORES TWIST-LOCK®. Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR DE ESCRITORIO (H2) y al FONDO (N). Apriete cuatro SUJETADORES TWIST-LOCK®. NOTA: Asegúrese de que las ESPIGAS DE METAL de los PARALES GRANDES APUNTALADOS (Q) se inserten en los agujeros del ESTANTE PEQUEÑO DE ORGANIZADOR (M).
PASO 23 PASO 27 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Inserte un EXCÉNTRICO DE CORREDERA (TTT) dentro de los LADOS DE CAJÓN (D24 y D25). La PUERTA puede requerir ajustes. Siga el texto abajo para hacer los ajustes necesarios. Fije el CAJÓN DERECHO (40CC) y el CAJÓN IZQUIERDO (40CD) a los LADOS DE CAJÓN (D24 y D25). Utilice cuatro tornillos DORADOS de cabeza PERDIDA de 8 mm (RRR) a través de los agujeros No. 2 y No. 4.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
