sauder.com Get all organized and stuff. Lateral File Harbor View Collection | 158002 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-24 Español pg 25-28 Lot # 376082 08/27/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-20 Hammer Français 21-24 Español 25-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification D Q P R H C G A H E B S O S F N D256 D61 D729 D88 I M63 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. JJ KK BLACK 1-7/8" FLAT HEAD SCREW - 2 BLACK 1-1/8" PAN HEAD SCREW - 2 31S BLACK 7/8" FLAT HEAD SCREW - 7 MM SILVER 3/4" PAN HEAD SCREW - 2 NN BLACK 9/16" LARGE HEAD SCREW - 14 OO BROWN 7/16" LARGE HEAD SCREW - 5 PP QQ NAIL - 26 GOLD 5/16" FLAT HEAD SCREW - 8 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (Y) into the large holes in the ENDS (A and B). Repeat this step for the UPRIGHT (C), SHELF (E), and BOTTOM (F). Do not tighten the TWIST-LOCK® FASTENERS in this step. Y (17 used) B A Page 6 158002 www.sauder.
Step 2 å Tap two MOLDING CONNECTORS (EE) into the notches in the MOLDINGS (P, Q, and R). Use your hammer to tap the MOLDING CONNECTORS (EE) into the notches in the MOLDINGS. Flat end EE Unfinished surface Flat end R EE Unfinished surface Q P www.sauder.
Step 3 å Fasten the MOLDINGS (P, Q, and R) to the TOP (D). Use seven BLACK 7/8" FLAT HEAD SCREWS (31S). Remember: Righty tighty. Lefty loosey. 31S BLACK 7/8" FLAT HEAD SCREW (7 used in this step) Finished surface R Un fin ish ed su rfa ce Finished surface Q P D Long finished edge Page 8 158002 www.sauder.
Step 4 å Separate the EXTENSION SLIDES (U) from the EXTENSION RAILS (T) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (T) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (PP). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
Step 5 å å Fasten the LEFT END (B) to the LEFT MOLDING (R). Tighten two TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. Fasten the UPRIGHT (C) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 6 å Fasten the SHELF (E) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å Fasten the SHELF (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (JJ). å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å Fasten the RIGHT END (A) to the SHELF (E), BOTTOM (F), and RIGHT MOLDING (Q). Tighten six TWIST-LOCK® FASTENERS.
Step 7 å Fasten the SHELF MOLDING (O) to the SHELF (E). Tighten three TWIST-LOCK® FASTENERS. å NOTE: The SHELF MOLDING should overhang the top surface of the SHELF slightly. å Fasten the END MOLDINGS (S) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (NN) through the METAL BRACKETS and into the END MOLDINGS. å NOTE: The END MOLDINGS should overhang the inside surface of the ENDS. There are no pre-drilled holes in the END MOLDINGS. The SCREWS will tighten into the grooves.
Step 8 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Make equal margins along all four edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (G) to your unit using the NAILS (QQ). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å Push a HIDDEN CAM (1F) into the DRAWER BRACE (M63).
Step 9 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D256 D729 D256 I D88 I Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove Insert the DRAWER SIDES (D88 and D256) at an angle into the slot at each end of the DRAWER FRONT (I).
Step 10 å å Insert a SLIDE CAM (RR) into the DRAWER SIDES (D88 and D256). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten the EXTENSION SLIDES (U) to the DRAWER SIDES (D88 and D256). Use four GOLD 5/16" FLAT HEAD SCREWS (PP) through holes #1 and #4. RR Open end Screw head - turn CAM to line up holes in the SLIDES with holes in DRAWER SIDES 1 2 U 4 3 D88 RR D256 Open end U 1 2 43 PP GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 11 å Fasten the KNOBS (GG) to the DRAWER FRONT (I). Use two BLACK 1-1/8" PAN HEAD SCREWS (KK). å Fasten the FRONT FILE BRACKET (CC) to the DRAWER FRONT (I). Use two BROWN 7/16" LARGE HEAD SCREWS (OO). å Fasten the REAR FILE BRACKET (DD) to the DRAWER BACK (D61). Use two BROWN 7/16" LARGE HEAD SCREWS (OO). å Fasten the LOCK BRACKET (BB) to the RIGHT DRAWER SIDE (D256). Use a BROWN 7/16" LARGE HEAD SCREWS (OO).
Step 12 å å Push a FILE GLIDE (W) onto the RIGHT DRAWER SIDE (D256). å Slide another FILE GLIDE (W) onto the other ends of the FILE RODS (X2), then press this FILE GLIDE over the LEFT DRAWER SIDE (D88). Slide the FILE RODS (X2) through a FILE BAR (V2), through the holes in the FILE BRACKETS (CC and DD), through another FILE BAR (V2), and into the FILE GLIDE (W) on the RIGHT DRAWER SIDE (D256). X2 W X2 DD D88 V2 V2 W D256 CC www.sauder.
Step 13 å å Carefully stand your unit upright. å NOTE: Be sure the metal bar on the LOCK is facing the direction shown. å Push the LOCK COVER (AA) over the key extension on the LOCK. Pro Tip: Lift with your legs. And, you know, your arms. Fasten the LOCK (Z) to the inside of the RIGHT END (A). Use two SILVER 3/4" PAN HEAD SCREWS (MM). MM SILVER 3/4" PAN HEAD SCREW (2 used in this step) Metal bar AA Z A Page 18 158002 www.sauder.
Step 14 å To insert the drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. å Push the RUBBER SLEEVES (II) over the METAL PINS (HH). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS.
Step 15 å To make adjustments to the drawer, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREW when finished with adjustments.
158002 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (Y) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette étape pour le MONTANT (C), la TABLETTE (E) et le DESSOUS (F).
ÉTAPE 7 ÉTAPE 9 Fixer la MOULURE DE TABLETTE (O) à la TABLETTE (E). Serrer trois FIXATIONS TWIST-LOCK®. 1. Insérer les CÔTÉS DE TIROIR (D88 et D256) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (I). REMARQUE : La MOULURE DE TABLETTE doit dépasser légèrement la surface supérieure de la TABLETTE. 2. Enfiler le FOND DE TIROIR (D729) dans les rainures des CÔTÉS DE TIROIR (D88 et D256) et du DEVANT DE TIROIR (I). Fixer les MOULURES D'EXTRÉMITÉ (S) aux EXTRÉMITÉS (A et B).
ÉTAPE 12 ÉTAPE 14 Enfoncer une ARMATURE POUR DOSSIERS (W) sur le CÔTÉ DROIT DE TIROIR (D256). Pour insérer le tiroir dans l'élément, aligner les COULISSES D'EXTENSION du tiroir sur les GLISSIÈRES D'EXTENSION de l'élément et enfoncer le tiroir dans l'élément jusqu'à ce que le tiroir soit complètement inséré. Le tiroir offrira une certaine résistance jusqu'à ce qu'il soit complètement inséré dans l'élément, il glissera ensuite sans difficulté.
158002 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los SUJETADORES TWIST-LOCK® en este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (Y) en los agujeros grandes de los EXTREMOS (A y B). Repita este paso para el PARAL (C), el ESTANTE (E) y el FONDO (F).
PASO 7 PASO 9 Fije la MOLDURA DE ESTANTE (O) al ESTANTE (E). Apriete tres SUJETADORES TWIST-LOCK®. 1. Inserte los LADOS DE CAJÓN (D88 y D256) en ángulo en el encaje en cada extremo de la CARA DE CAJÓN (I). NOTA: La MOLDURA DE ESTANTE debe sobresalir ligeramente de la superficie superior del ESTANTE. 2. Deslice el FONDO DE CAJÓN (D729) en las ranuras de los LADOS DE CAJÓN (D88 y D256) y de la CARA DE CAJÓN (I). Fije las MOLDURAS DE EXTREMO (S) a los EXTREMOS (A y B).
PASO 12 PASO 14 Empuje un CORRIMIENTO DE ARCHIVERO (W) sobre el LADO DERECHO DE CAJÓN (D256). Deslice las VARILLAS DE ARCHIVERO (X2) a través de una BARRA DE ARCHIVERO (V2), a través de los agujeros de las MÉNSULAS DE ARCHIVERO (CC y DD), a través de otra BARRA DE ARCHIVERO (V2) y dentro del CORRIMIENTO DE ARCHIVERO (W) sujetada al LADO DERECHO DE CAJÓN (D256).
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded file cabinet drawers. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading drawers. Place the heavier items on lower drawers.
PRECAUCIÓN Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones del gabinete de archivo sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
