2010 Saturn VUE Owner Manual M In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information . . . . . . . . 1-3 Vehicle Features . . . . . . . . . . . . . 1-14 Performance and Maintenance . . . . . . . . . . . . . . . . 1-17 Keys, Doors and Windows . . . 2-1 Keys and Locks . . . . . . . . . . . . . . . 2-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Vehicle Security. . . . . . . . . . . . . . . .
010 Saturn VUE Owner Manual M Vehicle Care . . . . . . . . . . . . . . . . . 10-1 General Information . . . . . . . . . . 10-2 Vehicle Checks . . . . . . . . . . . . . . . 10-4 Headlamp Aiming . . . . . . . . . . . 10-30 Bulb Replacement . . . . . . . . . . 10-33 Electrical System . . . . . . . . . . . . 10-37 Wheels and Tires . . . . . . . . . . . 10-43 Jump Starting . . . . . . . . . . . . . . . 10-74 Towing . . . . . . . . . . . . . . . . . . . . . . 10-78 Appearance Care . . . . . . . . . . .
Introduction SATURN, the SATURN Emblem, and the name VUE are registered trademarks of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name "General Motors of Canada Limited" for Saturn Corporation wherever it appears in this manual.
iv Introduction Using this Manual To quickly locate information about the vehicle, use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Danger, Warnings, and Cautions { WARNING These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicle damage. This would not be covered by the vehicle's warranty.
Introduction Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio® Steering Wheel Controls or OnStar $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant Temperature O : Exterior Lamps # : Fog Lamps .
vi Introduction 2 NOTES
In Brief In Brief Instrument Panel Instrument Panel . . . . . . . . . . . . . . 1-2 Initial Drive Information Initial Drive Information . . . . . . . . 1-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 1-3 Remote Vehicle Start . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . 1-5 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Windows . . . . . . . . . . . . . . . . . . . . . . 1-5 Seat Adjustment . . . . . . . . . . . . . .
1-2 In Brief Instrument Panel
In Brief A. Air Vents on page 8‑9. B. Instrument Panel Illumination Control on page 6‑5. M. Steering Wheel Adjustment on page 5‑2. N. Horn on page 5‑3. C. Turn and Lane-Change Signals on page 6‑4. O. Steering Wheel Controls on page 5‑3. D. Instrument Cluster on page 5‑10. P. Rear Window Wiper/Washer on page 5‑5. E. Windshield Wiper/Washer on page 5‑3. Q. Traction Control System (TCS) on page 9‑40. F. AM-FM Radio on page 7‑4. R. Shift Lever. See Automatic Transmission on page 9‑35. G.
1-4 In Brief Press L and hold to sound the panic alarm. Press L again to cancel the panic alarm. See Remote Keyless Entry (RKE) System Operation on page 2‑3. Remote Vehicle Start Starting the Vehicle Remote Start Not Shown Press K to unlock the driver door. Press K again within five seconds to unlock all remaining doors. Press Q to lock all doors, including the liftgate. Lock and unlock feedback can be personalized. Press L and release to locate the vehicle.
In Brief Door Locks To lock or unlock a door, use the key from the outside or the door lock from the inside. See Door Locks on page 2‑6. Power Door Locks T : The power door lock switches are located on the driver door. To open the liftgate, press the touchpad on the underside of the liftgate handle and pull up. Press the front of the switch to open the window. Pull the switch up to close it. To close the liftgate, pull down using the handle and close until it latches.
1-6 In Brief Seat Adjustment Power Seats Manual Seats This vehicle may have power seats. To move a manual seat forward or rearward: To adjust the seat location, move the control forward or rearward. 1. Lift the bar to unlock the seat. 2. Slide the seat to the desired position and release the bar. Try to move the seat with your body to be sure the seat is locked in place. See Seat Adjustment on page 3‑3.
In Brief Seat Height Adjuster Reclining Seatbacks — Manual On seats with manual reclining seatbacks, use the lever located on the outboard side of the seat. 1-7 See Reclining Seatbacks on page 3‑5. Reclining Seatbacks — Power On seats with power reclining seatbacks, the control is located on the outboard side of the seat. On vehicles with this feature, move the lever upward repeatedly to raise the seat. Move the lever downward repeatedly to lower the seat.
1-8 In Brief Lumbar Adjustment Heated Seats On vehicles with heated front seats, the controls are located on the center console. The engine must be running to operate the heated seats. M : Press this button to turn on the heated seat. Continue to press the button to cycle through the temperature settings. If the vehicle has this feature, the knob is located on the inboard side of the driver seatback. Turn the knob clockwise or counterclockwise to increase or decrease the lumbar support.
In Brief Safety Belt Sensing System for Passenger Airbag United States Refer to the following sections for important information on how to use safety belts properly. . Safety Belts on page 3‑10. . How to Wear Safety Belts Properly on page 3‑13. . Lap-Shoulder Belt on page 3‑19. . Lower Anchors and Tethers for Children (LATCH System) on page 3‑50.
1-10 In Brief Mirror Adjustment Exterior Mirrors 3. Return the control to the center position so the mirror cannot be moved. Steering Wheel Adjustment The mirrors can be manually folded inward toward the vehicle. Return to the original position to use correctly. See Power Mirrors on page 2‑12. Interior Mirrors Controls for the outside power mirrors are located on the driver door. 1. Turn the knob to choose the left (L) or the (R) right mirror. 2.
In Brief See Steering Wheel Adjustment on page 5‑2. Interior Lighting Dome Lamp * : Press this button on the overhead console to keep the dome lamps and other interior lamps turned off while any door is open. Press this button again to return it to the out position and the lamps automatically come on when any door is opened. For more information on interior lamps, see: . Dome Lamps on page 6‑5. . Instrument Panel Illumination Control on page 6‑5.
1-12 In Brief Windshield Wiper/Washer &: Sets a delay between wipes. Move the switch on top of the lever left for less frequent wipes or right for more frequent wipes. a: 1: Slow wipes. Fast wipes. Windshield Washer Pull the windshield wiper lever to spray windshield washer fluid and activate the wipers. See Windshield Wiper/Washer on page 5‑3. The windshield wiper lever is on the right side of the steering column. 8: Single wipe, briefly move the lever down.
In Brief Climate Controls The heating, cooling, and ventilation for the vehicle can be controlled by this system. Vehicles with automatic climate control automatically maintain the desired temperature inside the vehicle. United States version shown, Canada version similar. A. Fan Control F. Air Recirculation B. Temperature Control G. Rear Window Defogger C. Air Delivery Mode Control See Climate Control Systems on page 8‑1 and Automatic Climate Control System on page 8‑5. D. Air Conditioning E.
1-14 In Brief the current FM-RDS or XM station; or CD, MP3 or WMA song. If information is available during XM, CD, MP3 or WMA playback, the song title information displays on the top line of the display and artist information displays on the bottom line. When information is not available, "NO INFO" displays. Vehicle Features Radio(s) For more information about these and other radio features, see Operation on page 7‑2. Storing a Favorite Station O (Power/Volume): Press to turn the system on and off.
In Brief 1-15 Setting the Clock Satellite Radio Portable Audio Devices To set the time and date: Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. This vehicle may have a 3.5 mm (1/8 in) auxiliary input, located on the radio faceplate. External devices such as iPod®, MP3 players, etc. can be connected to the 3.5 mm (1/8 in) auxiliary input using a 3.5 mm (1/8 in) input jack cable. 1. Turn the ignition key to ACC/ ACCESSORY or ON/RUN.
1-16 In Brief Steering Wheel Controls J 0 : Press and release to mute the system. Press it again to turn the sound back on. Cruise Control Press and hold longer than two seconds to interact with the OnStar® or Bluetooth systems. For more information, see Steering Wheel Controls on page 5‑3. Navigation System Some audio controls can be adjusted at the steering wheel. They include the following: + / − : Press and release to go to the next or the previous preset radio station or CD track.
In Brief Power Outlets Performance and Maintenance The accessory power outlets can be used to connect electrical equipment, such as a cellular phone. The accessory power outlets are located on the rear of the center storage console and in the rear cargo compartment. There may be a power outlet located inside the instrument panel storage area below the climate controls. See Power Outlets on page 5‑8. Sunroof The sunroof switch is located between the sun visors.
1-18 In Brief StabiliTrak® Tire Pressure Monitor The StabiliTrak system assists with directional control of the vehicle in difficult driving conditions. The system turns on automatically every time the vehicle is started. This vehicle may have a Tire Pressure Monitor System (TPMS). . . To turn off both Traction Control and StabiliTrak, press and hold 5 until F illuminates and the appropriate DIC message displays. See Vehicle Messages on page 5‑31. Press the button again to turn on both systems.
In Brief Engine Oil Life System The engine oil life system calculates engine oil life based on vehicle use and turns on the change engine oil light when it is time to change the engine oil and filter. The oil life system should be reset to 100% only following an oil change. The oil life system can also be reset as follows: . Avoid idling the engine for long periods of time. 1. Turn the ignition key to ON/RUN with the engine off. .
1-20 In Brief Roadside Assistance Program U.S.: 1-800-553-6000 TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Saturn, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
In Brief Crisis Assist, Stolen Vehicle Assistance, Vehicle Diagnostics, Remote Door Unlock, Roadside Assistance, Turn‐by‐Turn Navigation and Hands‐Free Calling are available on most vehicles. Not all OnStar services are available on all vehicles. For more information see the OnStar Owner's Guide or visit www.onstar.com (U.S.) or www.onstar.ca (Canada), contact OnStar at 1-888-4-ONSTAR (1‐888‐466‐7827) or TTY 1‐877‐248‐2080, or press Q to speak with an OnStar advisor 24 hours a day, 7 days a week.
1-22 In Brief OnStar Steering Wheel Controls This vehicle may have a Talk/Mute button that can be used to interact with OnStar hands-free calling. See Steering Wheel Controls on page 5‑3 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions. See the OnStar Owner's Guide for more information. Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard.
Keys, Doors and Windows Keys, Doors and Windows Vehicle Security Vehicle Security . . . . . . . . . . . . . . . 2-9 Anti-Theft Alarm System . . . . . . 2-9 Immobilizer . . . . . . . . . . . . . . . . . . 2-10 Immobilizer Operation . . . . . . . 2-10 Keys and Locks Keys . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry (RKE) System Operation . . . . . . . . . . . Remote Vehicle Start . . . . . . . . .
2-2 Keys, Doors and Windows Remote Keyless Entry (RKE) System Keys and Locks Keys See Radio Frequency Statement on page 13‑16 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry and Science Canada. { WARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move.
Keys, Doors and Windows . Check the transmitter's battery. See “Battery Replacement” later in this section. . If the transmitter is still not working correctly, see your dealer/retailer or a qualified technician for service. K (Unlock): Press once to unlock the driver door. If K is pressed again within five seconds, all remaining doors unlock. The interior lamps come on and stay on for 20 seconds or until the ignition is turned on. The exterior lamps may flash when unlocking the vehicle.
2-4 Keys, Doors and Windows Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen transmitters no longer work once the new transmitter is programmed. Each vehicle can have up to eight transmitters programmed to it.
Keys, Doors and Windows If the vehicle has the remote start feature, the RKE transmitter functions have an increased range of operation. However, the range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry (RKE) System on page 2‑2 for additional information. Starting the Engine Using Remote Start To start the vehicle: 1. Aim the RKE transmitter at the vehicle. 2. Press Q on the RKE transmitter. 3.
2-6 Keys, Doors and Windows Shutting the Engine Off After a Remote Start Door Locks { WARNING To manually shut off a remote start: . Aim the RKE transmitter at the vehicle and press / until the parking lamps turn off. . Turn on the hazard warning flashers. . Turn the ignition switch on and then off. injuries or even death from heat stroke. Always lock the vehicle whenever leaving it. Unlocked doors can be dangerous. .
Keys, Doors and Windows Delayed Locking Lockout Protection A chime will sound to indicate a door or liftgate is open when you try to lock the doors with the power door lock switch. The doors will not lock, and the theft‐deterrent system will not arm until all the doors are closed and five seconds have passed. When the power door lock switch is pressed with the key in the ignition, and any door is open, all the doors lock and the driver door unlocks.
2-8 Keys, Doors and Windows Doors WARNING (Continued) Liftgate . Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. . If the vehicle is equipped with a power liftgate, disable the power liftgate function.
Keys, Doors and Windows Vehicle Security Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Anti-Theft Alarm System Your vehicle may have a content theft-deterrent alarm system. United States shown, Canada similar The security light is located near the center of the instrument panel.
2-10 Keys, Doors and Windows Testing the Alarm To test the alarm: 1. From inside the vehicle, lower the driver window and open the driver door. 2. Get out of the vehicle, close the door and activate the system by locking the doors with the RKE transmitter. 3. Wait for the security light to flash slowly. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm.
Keys, Doors and Windows If the engine still does not start, and the key appears to be not damaged, wait about five minutes and try another ignition key and check the fuse. See Fuses and Circuit Breakers on page 10‑37. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer/ retailer who can service the PASS-Key® III+ to have a new key made. In an emergency, contact Roadside Assistance.
2-12 Keys, Doors and Windows Exterior Mirrors Power Mirrors 1. Turn the knob to choose the left (L) or the (R) right mirror. Convex Mirrors 2. Adjust each mirror so that you can see the side of your vehicle and the area behind your vehicle. { WARNING A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
Keys, Doors and Windows Interior Mirrors Manual Rearview Mirror If the vehicle has the manual rearview mirror, it can be adjusted by holding the mirror in the center to move it for a clearer view behind the vehicle. Reduce the glare of headlamps from behind by turning the lever for daytime or nighttime use. Vehicles with OnStar® have three additional control buttons for the OnStar® system. See your dealer/ retailer for more information about OnStar® and how to subscribe to it.
2-14 Keys, Doors and Windows Power Windows Express-Down Window The driver window switch has an express-down feature that lowers the window without holding the switch. Press the switch part way and the window will open a small amount. Press the switch down all the way and release it and the window lowers all the way. { WARNING Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Keys, Doors and Windows Window Lockout o (Window Lockout): The vehicle has a lockout feature to prevent rear seat passengers from operating the windows. Press the lockout button, located with the power window switches, to turn the feature on and off. Roof Sunroof Open/Close: Slide and release the switch rearward to express open the sunroof. Slide the switch forward or rearward to stop movement. The sun shade opens automatically with the sunroof or can be manually operated.
2-16 Keys, Doors and Windows 2 NOTES
Seats and Restraints Seats and Restraints Safety System Check . . . . . . . . 3-23 Safety Belt Care . . . . . . . . . . . . . 3-24 Replacing Safety Belt System Parts After a Crash . . . . . . . . . 3-24 Airbag System Head Restraints Head Restraints . . . . . . . . . . . . . . . 3-2 Active Head Restraints . . . . . . . . 3-3 Front Seats Seat Adjustment . . . . . . . . . . . . . . Power Seat Adjustment . . . . . . . Lumbar Adjustment . . . . . . . . . . . Reclining Seatbacks . . . . . . . . . .
3-2 Seats and Restraints Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { WARNING With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head.
Seats and Restraints Active Head Restraints This vehicle has an active head restraint system in the front outboard seating positions. The active head restraints automatically tilt forward to reduce the risk of neck injury if the vehicle is hit from behind. Front Seats 3-3 To move a manual seat forward or rearward: Seat Adjustment { WARNING You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving.
3-4 Seats and Restraints Seat Height Adjuster Power Seat Adjustment This vehicle may have power seats. If the vehicle has a manual driver seat height adjuster, it is located on the outboard side of the seat near the front of the seat cushion. To raise the seat, move the lever upward repeatedly until the seat is at the desired height. To lower the seat, move the lever downward repeatedly until the seat is at the desired height. To adjust the seat location, move the control forward or rearward.
Seats and Restraints Lumbar Adjustment 3-5 Reclining Seatbacks Manual Reclining Seatbacks { WARNING If the vehicle has this feature, the knob is located on the inboard side of the driver seatback. Turn the knob clockwise to increase lumbar support and counterclockwise to decrease it. You can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
3-6 Seats and Restraints To recline the seatback: Power Reclining Seatbacks 1. Lift the recline lever. Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked. The shoulder belt cannot do its job.
Seats and Restraints Heated Front Seats WARNING (Continued) On vehicles with heated front seats, the controls are located on the center console. The engine must be running to operate the heated seats. The lap belt cannot do its job either. In a crash the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright.
3-8 Seats and Restraints Folding Seatback The front passenger seatback may fold flat. { WARNING If you fold the seatback forward to carry longer objects, such as skis, be sure any such cargo is not near an airbag. In a crash, an inflating airbag might force that object toward a person. This could cause severe injury or even death. Secure objects away from the area in which an airbag would inflate. For more information, see Where Are the Airbags? on page 3‑27 and Vehicle Load Limits on page 9‑22.
Seats and Restraints To raise the seatback: 1. Lift the recliner lever, located on the outboard side of the seat, up fully and push up on the seatback. 2. Continue raising the seatback until the seatback re-engages. { WARNING If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push and pull on the seatback to make sure it is locked in place.
3-10 Seats and Restraints Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { WARNING 2. Lift the lever located on the top of the seatback to release the seatback and fold the seatback forward. To recline the seatback: 1. Lift and hold the lever located on top of the seatback. 2. Tilt the seatback rearward, then release the lever. Do not let anyone ride where a safety belt cannot be worn properly.
Seats and Restraints 3-11 In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
3-12 Seats and Restraints With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...
Seats and Restraints Q: If my vehicle has airbags, why should I have to wear safety belts? A: Airbags are supplemental systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection. That is true not only in frontal collisions, but especially in side and other collisions.
3-14 Seats and Restraints First, before you or your passenger(s) wear a safety belt, there is important information you should know. applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Seats and Restraints { WARNING Q: What is wrong with this? You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. 3-15 { WARNING You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries.
3-16 Seats and Restraints Q: What is wrong with this? { WARNING Q: What is wrong with this? You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong buckle. A: The belt is over an armrest.
Seats and Restraints { WARNING Q: What is wrong with this? You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
3-18 Seats and Restraints Q: What is wrong with this? A: The belt is behind the body. { WARNING You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries.
Seats and Restraints Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 3-19 The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
3-20 Seats and Restraints Shoulder Belt Height Adjuster 4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjuster” later in this section for instructions on use and important safety information. The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Seats and Restraints They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. And, for vehicles with side impact airbags, safety belt pretensioners can help tighten the safety belts in a side crash or a rollover event. Squeeze the release buttons (A) together and move the height adjuster up or down to the desired position.
3-22 Seats and Restraints { WARNING A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. 4.
Seats and Restraints Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
3-24 Seats and Restraints Safety Belt Care Keep belts clean and dry. { WARNING Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Replacing Safety Belt System Parts After a Crash { WARNING A crash can damage the safety belt system in the vehicle.
Seats and Restraints Airbag System The vehicle has the following airbags: All of the airbags in the vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. . A frontal airbag for the driver. . A frontal airbag for the right front passenger. . A seat-mounted side impact airbag for the driver. . A seat-mounted side impact airbag for the right front passenger.
3-26 Seats and Restraints Here are the most important things to know about the airbag system: { WARNING You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them. Also, airbags are not designed to deploy in every crash. In some crashes safety belts are your only restraint. See When Should an Airbag Inflate? on page 3‑29.
Seats and Restraints 3-27 Where Are the Airbags? There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 5‑13 for more information. The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side.
3-28 Seats and Restraints { WARNING Driver Side shown, Passenger Side similar Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door. The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows.
Seats and Restraints When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold. Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants.
3-30 Seats and Restraints In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. For moderate frontal impacts, dual-stage airbags inflate at a level less than full deployment. For more severe frontal impacts, full deployment occurs.
Seats and Restraints What Makes an Airbag Inflate? How Does an Airbag Restrain? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy. The inflator, the airbag, and related hardware are all part of the airbag module. In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel.
3-32 Seats and Restraints What Will You See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy. Some components of the airbag module may be hot for several minutes. For location of the airbag modules, see What Makes an Airbag Inflate? on page 3‑31.
Seats and Restraints You can lock the doors, turn off the interior lamps and hazard warning flashers by using the controls for those features. You must first, however, turn the ignition key to the following ignition switch positions: In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. 1. Turn the ignition key to LOCK/OFF. . 2. Turn the ignition key to ON/RUN.
3-34 Seats and Restraints Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. United States Canada The words ON and OFF, or the symbol for on and off, are visible during the system check. If you are using remote start, if equipped, to start the vehicle from a distance, you may not see the system check.
Seats and Restraints A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { WARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
3-36 Seats and Restraints The passenger sensing system is designed to turn off the right front passenger airbag and seat‐mounted side impact airbag if: . The right front passenger seat is unoccupied. . The system determines that an infant is present in a rear-facing infant seat. . The system determines that a small child is present in a child restraint. . The system determines that a small child is present in a booster seat. .
Seats and Restraints If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers. 4.
3-38 Seats and Restraints If the Off Indicator is Lit for an Adult-Size Occupant enable the right front passenger frontal airbag and seat-mounted side impact airbag: 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers. 3. Place the seatback in the fully upright position.
Seats and Restraints A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your specific vehicle. See Adding Equipment to the Airbag-Equipped Vehicle on page 3‑40 for more information about modifications that can affect how the system operates.
3-40 Seats and Restraints Adding Equipment to the Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Seats and Restraints Airbag System Check The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 5‑13 for more information. Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly. Do not open or break the airbag coverings. If there are any opened or broken airbag covers, have the airbag covering and/or airbag module replaced.
3-42 Seats and Restraints Child Restraints Older Children The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. . Buckle the lap-shoulder belt. Does the shoulder belt rest on the shoulder? If yes, continue.
Seats and Restraints According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. WARNING (Continued) might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest.
3-44 Seats and Restraints Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Seats and Restraints { WARNING Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.
3-46 Seats and Restraints Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available.
Seats and Restraints 3-47 Child Restraint Systems (B) Forward-Facing Child Seat (A) Rear-Facing Infant Seat A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child's body with the harness.
3-48 Seats and Restraints Securing an Add-On Child Restraint in the Vehicle { WARNING A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle.
Seats and Restraints child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “Never put a rear-facing child restraint in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { WARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
3-50 Seats and Restraints Lower Anchors and Tethers for Children (LATCH System) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Seats and Restraints Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints that have top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
3-52 Seats and Restraints Securing a Child Restraint Designed for the LATCH System { WARNING Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat.
Seats and Restraints { WARNING Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts.
3-54 Seats and Restraints Refer to the child restraint instructions and the following steps: are using a single tether, route the tether over the seatback. 2.1. Find the top tether anchor. 2.2. Route, attach, and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback.
Seats and Restraints Replacing LATCH System Parts After a Crash { WARNING If the position you are using has an adjustable headrest or head restraint and you are using a single tether, raise the headrest or head restraint and route the tether under the headrest or head restraint and in between the headrest or head restraint posts. 3. Push and pull the child restraint in different directions to be sure it is secure. A crash can damage the LATCH system in the vehicle.
3-56 Seats and Restraints Securing Child Restraints (Rear Seat Position) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑50 for how and where to install the child restraint using LATCH.
Seats and Restraints 3-57 6. If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑50 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5.
3-58 Seats and Restraints Securing Child Restraints (Front Seat Position) { WARNING WARNING (Continued) The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3‑48. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
Seats and Restraints If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑50 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑50 for top tether anchor locations.
3-60 Seats and Restraints 7. If the vehicle does not have a rear seat and the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑50 for more information. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6.
Storage Storage Storage Compartments Storage Compartments Instrument Panel Storage . . . . Glove Box . . . . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . . . Front Storage . . . . . . . . . . . . . . . . . Sunglasses Storage . . . . . . . . . . Armrest Storage . . . . . . . . . . . . . . Center Console Storage . . . . . . 4-1 4-1 4-1 4-2 4-2 4-2 4-2 Additional Storage Features Cargo Cover . . . . . . . . . . . . . . . . . . Cargo Tie Downs . . . . . . . . . . . . .
4-2 Storage Front Storage Armrest Storage Center Console Storage For vehicles with a storage area located under the front passenger seat, lift up on the end of the tray and pull it forward to access it. To access the rear seat armrest, pull the handle down. Lift the top of the armrest to access the storage area. Your vehicle has a center console with an upper, lower and rear storage area. To access the upper storage area, lift up on the top lever.
Storage Additional Storage Features Cargo Cover For vehicles with a cargo cover, use it to cover items in the rear of the vehicle. To open the cover of the the rear storage area, push the button located at the top. To remove the cover and remove it from the vehicle, pull both ends toward each other. To reinstall, place each end of the cover in the holes behind the rear seat. 4-3 Cargo Tie Downs Four cargo tie‐downs are located in the rear compartment of the vehicle.
4-4 Storage The hooks hold the mesh pocket. To insert a hook on the rail, place the hook in the upper groove of the rail and press it into the lower groove. Convenience Net For vehicles with a convenience net, located in the rear, use it to store small loads as far forward as possible. The net should not be used to store heavy loads. The adapters are used to hold the net. Slide the adapters to the desired location on the upper and lower rail and turn the handle up to lock it in place.
Storage Notice: Loading cargo on the roof rack that weighs more than 75 kg (165 lbs) or hangs over the rear or sides of the vehicle may damage the vehicle. Load cargo so that it rests evenly between the crossrails, making sure to fasten cargo securely. To prevent damage or loss of cargo when driving, check to make sure crossrails and cargo are securely fastened. Loading cargo on the roof rack will make the vehicle’s center of gravity higher.
4-6 Storage 2 NOTES
Instruments and Controls Instruments and Controls Controls Steering Wheel Adjustment . . . 5-2 Steering Wheel Controls . . . . . . 5-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Windshield Wiper/Washer . . . . . 5-3 Rear Window Wiper/ Washer . . . . . . . . . . . . . . . . . . . . . . 5-5 Compass . . . . . . . . . . . . . . . . . . . . . 5-5 Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Power Outlets . . . . . . . . . . . . . . . . .
5-2 Instruments and Controls Tire Messages . . . . . . . . . . . . . . . 5-37 Transmission Messages . . . . . 5-38 Vehicle Reminder Messages . . . . . . . . . . . . . . . . . . 5-39 Vehicle Personalization Controls Steering Wheel Adjustment Vehicle Personalization . . . . . . 5-39 To adjust the steering wheel: 1. Hold the steering wheel and pull the lever down. 2. Move the steering wheel up or down to a comfortable position. 3. Pull the lever up firmly to lock the steering wheel in place.
Instruments and Controls Steering Wheel Controls For vehicles with Bluetooth®, press to end a call, or cancel an incoming call. 5-3 Windshield Wiper/Washer See Bluetooth on page 7‑18 and the OnStar Owner's Guide for more information. v + v −(Volume): Move the thumbwheel up or down to increase or to decrease the volume. J 0 (Call / Mute): Press and release to mute the system. Press it again to turn the sound back on. Some audio controls can be adjusted at the steering wheel.
5-4 Instruments and Controls & (Adjustable Interval Wipes): Sets a delay between wipes. Move the switch on top of the lever left for less frequent wipes or right for more frequent wipes. a (Low): Slow wipes. 1 (High): Fast wipes. Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. See Wiper Blade Replacement on page 10‑29. Heavy snow or ice can overload the wiper motor.
Instruments and Controls Windshield Washer { WARNING In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Pull the windshield wiper lever to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached.
5-6 Instruments and Controls To adjust for compass variance, use the following procedure: 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. Compass Variance (Zone) Procedure 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following. 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park).
Instruments and Controls If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic CB or cell phone antenna mount, a magnetic emergency light, magnetic note pad holder, or any other magnetic item. Turn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass.
5-8 Instruments and Controls Clock To set the time and date: 1. Turn the ignition key to ACC/ ACCESSORY or ON/RUN. Press O to turn the radio on. 2. Press H and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 3. Press the softkey located below any one of the tabs that you want to change. 4. To increase the time or date do one of the following: . Press the softkey located below the selected tab. . Press ¨ SEEK, or \ FWD. . Turn f clockwise. 5.
Instruments and Controls Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet.
5-10 Instruments and Controls Instrument Cluster United States Base version shown, Canada and Uplevel similar
Instruments and Controls Speedometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer. If the vehicle needs a new odometer installed, the new one is set to the mileage of the old odometer. If this is not possible, it is set at zero and a label is put on the driver's door to show the old mileage reading.
5-12 Instruments and Controls Here are four things that some owners ask about. None of these means the fuel gage is not working properly: Safety Belt Reminders . At the service station, the fuel pump shuts off before the gage reads full. The driver safety belt reminder light is on the instrument panel cluster. . It takes a little more or less fuel to fill up than the gage indicated.
Instruments and Controls The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag's electrical system for malfunctions.
5-14 Instruments and Controls Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 3‑34 for important safety information. The instrument panel has a passenger airbag status indicator. United States If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag and seat‐mounted side impact airbag are enabled (may inflate).
Instruments and Controls { WARNING If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑13 for more information, including important safety information. Charging System Light The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working.
5-16 Instruments and Controls If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction.
Instruments and Controls Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected. . . Make sure the fuel cap is fully installed. See Filling the Tank on page 9‑50. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
5-18 . Instruments and Controls The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving.
Instruments and Controls { WARNING The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop.
5-20 Instruments and Controls This light flashes when the AWD system is temporarily disabled. For more information see All-Wheel Drive on page 9‑38. StabiliTrak® Indicator Light Traction Control System (TCS) Warning Light The StabiliTrak® light comes on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. This light comes on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer.
Instruments and Controls Engine Coolant Temperature Warning Light The engine coolant temperature light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 10‑20. The vehicle's engine could be damaged, and it might not be covered by the vehicle warranty.
5-22 Instruments and Controls Engine Oil Pressure Light Change Engine Oil Light { WARNING Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil.
Instruments and Controls Low Fuel Warning Light Security Light The low fuel warning light, below the fuel gage, comes on briefly when the engine is started. This light flashes when the security system is activated. This light also comes on when the fuel tank is low on fuel. When fuel is added, the light should go off. If it does not, have the vehicle serviced. For more information, see Vehicle Security on page 2‑9.
5-24 Instruments and Controls The vehicle can be driven at a reduced speed when the reduced engine power light is on but acceleration and speed might be reduced. The performance could be reduced until the next time the vehicle is driven. If this light stays on, see your dealer/retailer as soon as possible for diagnosis and repair. High-Beam on Light The highbeam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.
Instruments and Controls Cruise Control Light Gate Ajar Light 5-25 Information Displays Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑42 for more information. Door Ajar Light The door ajar light comes on when a door is open. Before driving, check that all doors are properly closed.
5-26 Instruments and Controls dashes. If this occurs, have the vehicle serviced by your dealer/ retailer. If an abnormal temperature reading is displayed for an extended period of time, consult your dealer/retailer. Under certain circumstances, especially when the engine is idling, a delay updating the temperature display is normal. See Compass on page 5‑5 and Automatic Transmission on page 9‑35 for more information.
Instruments and Controls Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items: Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see “Units” later in this section.
5-28 Instruments and Controls Fuel Used Press the trip/fuel button until FUEL USED displays. This display shows the number of gallons (gal) or liters (L) of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold the set/reset button while FUEL USED is displayed. Elapsed Time Press the trip/fuel button until ELAPSED TIME displays. This display can be used as a timer. To start the timer, press the set/ reset button while ELAPSED TIME is displayed.
Instruments and Controls When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under Engine Oil Messages on page 5‑33. You should change the oil as soon as you can. See Engine Oil on page 10‑8. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 11‑2 for more information.
5-30 Instruments and Controls Relearn Remote Key This display allows you to program Remote Keyless Entry (RKE) transmitters to your vehicle. When a new transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen transmitters no longer work once the new transmitter is programmed. To program an RKE transmitter to your vehicle: 1. Press the vehicle information button until PRESS V TO RELEARN REMOTE KEY displays. 2.
Instruments and Controls Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons, or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the messages and to clear them from the display.
5-32 Instruments and Controls Cruise Control Messages CRUISE SET TO XXX This message will display when the cruise control is set and it will show the speed it was set to. See Cruise Control on page 9‑42 for more information. Door Ajar Messages DRIVER DOOR OPEN This message will display when the driver door is not closed properly. Close the door completely. HOOD OPEN If your vehicle has the remote start feature, this message displays along with a chime when the hood is not closed properly.
Instruments and Controls ENGINE OVERHEATED IDLE ENGINE ENGINE OVERHEATED STOP ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 10‑20 for more information.
5-34 Instruments and Controls OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected. See Engine Oil on page 10‑8 for more information. This message displays when the vehicle's engine oil pressure is low.
Instruments and Controls Key and Lock Messages REMOTE KEY LEARNING ACTIVE This message displays while matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “MATCHING TRANSMITTERS TO YOUR VEHICLE” under Remote Keyless Entry (RKE) System Operation on page 2‑3 and Driver Information Center (DIC) on page 5‑25 for more information. REMOTE KEY LEARNING COMPLETE This message displays while matching a Remote Keyless Entry (RKE) transmitter to your vehicle.
5-36 Instruments and Controls STABILITRAK NOT READY If your vehicle has StabiliTrak, this message may display and the StabiliTrak indicator light on the instrument panel cluster may be on after first driving the vehicle and exceeding 20 mph (32 km/h) for 30 seconds. The StabiliTrak system is not functional until the light has turned off. See StabiliTrak System on page 9‑41 for more information.
Instruments and Controls Service Vehicle Messages Tire Messages SERVICE A/C (Air Conditioning) SYSTEM CHECK TIRE PRESSURE This message displays when there is a problem detected in the air conditioning system. Have the vehicle serviced by your dealer/ retailer. SERVICE POWER STEERING If the vehicle has electric power steering, this message displays if a problem has been detected with the power steering. See Steering on page 9‑5 for more information.
5-38 Instruments and Controls TIRE LEARNING ACTIVE Transmission Messages On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Rotation on page 10‑57, Tire Pressure Monitor System on page 10‑52, and Tire Pressure on page 10‑50 for more information.
Instruments and Controls Vehicle Reminder Messages Vehicle Personalization ICE POSSIBLE DRIVE WITH CARE Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly.
5-40 Instruments and Controls Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English. DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the PRESS V TO SET DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Instruments and Controls Press the customization button until PRESS V TO SET AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER DOOR AT KEY OUT: Only the driver's door will unlock when the key is taken out of the ignition.
5-42 Instruments and Controls REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2‑3 for more information. Press the customization button until PRESS V TO SET REMOTE DOOR UNLOCK appears on the DIC display.
Instruments and Controls EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until PRESS V TO SET EXIT LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature.
5-44 Instruments and Controls CHIME VOLUME REMOTE START This feature allows you to select the volume level of the chime. If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2‑4 for more information. Press the customization button until PRESS V TO SET CHIME VOLUME appears on the DIC display.
Instruments and Controls EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until PRESS V TO EXIT FEATURE SETTINGS appears in the DIC display. Press the set/reset button once to exit the menu. If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: .
5-46 Instruments and Controls Universal Remote System Programming If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature.
Instruments and Controls To program up to three devices: 1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to flash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2.
5-48 Instruments and Controls 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle.
Instruments and Controls two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends.
5-50 Instruments and Controls 2 NOTES
Lighting Lighting Exterior Lighting Exterior Lighting Turn the control to the following positions: Exterior Lamp Controls 9 (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Exterior Lamp Controls . . . . . . . . 6-1 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 6-2 Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2 Daytime Running Lamps (DRL) . . . . . . . . . . . . . . . . 6-2 Automatic Headlamp System . . . . . . . . . . . .
6-2 Lighting Lamps On Reminder A warning chime sounds, if the driver door is opened while the ignition is off and the lamps are on. Wiper‐Activated Headlamps The headlamps and parking lamps turn on automatically if the exterior lamp control is set in the AUTO position and the windshield wipers are turned on and have completed eight wipe cycles. When the ignition is turned off, the wiper-activated headlamps immediately turn off. They also turn off if the windshield wiper control is turned off.
Lighting When the DRL are on, the low-beam headlamps will be on. The taillamps, sidemarker, instrument panel lights and other lamps will not be on. 6-3 Automatic Headlamp System Hazard Warning Flashers | (Hazard Warning Flasher): When it is dark enough outside, the headlamps come on automatically. Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble.
6-4 Lighting Turn and Lane-Change Signals The lever returns to its starting position whenever it is released. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have the bulbs replaced. If a bulb is not burned out, check the fuse. See Instrument Panel Fuse Block on page 10‑40 and for burned-out bulbs. An arrow on the instrument panel cluster flashes in the direction of the turn or lane change.
Lighting Interior Lighting Instrument Panel Illumination Control The thumbwheel for this feature is on the left side of the steering wheel next to the exterior lamps control. Dome Lamps * (Dome Lamp Override): Press this button on the overhead console to keep the dome lamps and other interior lamps turned off while any door is open. Press this button again to return it to the out position and the lamps automatically come on when any door is opened.
6-6 Lighting Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging.
Infotainment System Infotainment System Introduction Introduction . . . . . . . . . . . . . . . . . . . 7-1 Theft-Deterrent Feature . . . . . . . 7-2 Operation . . . . . . . . . . . . . . . . . . . . . 7-2 Radio AM-FM Radio . . . . . . . . . . . . . . . . . 7-4 Satellite Radio . . . . . . . . . . . . . . . . 7-6 Radio Reception . . . . . . . . . . . . . 7-10 Fixed Mast Antenna . . . . . . . . . 7-11 Satellite Radio Antenna . . . . . . 7-11 Audio Players CD Player . . . . . . . . . . . . . . . . . . . .
7-2 Infotainment System See Retained Accessory Power (RAP) on page 9‑29 for more information. Operation Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Theft-Deterrent Feature THEFTLOCK® is designed to discourage theft of the vehicle's radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle.
Infotainment System If information is available during XM, CD, MP3 or WMA playback, the song title information displays on the top line of the display and artist information displays on the bottom line. When information is not available, "NO INFO" displays. Setting the Tone (Bass/ Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust bass, midrange, or treble: 1. Press the f knob until the tone control labels display. 2.
7-4 Infotainment System To quickly adjust all speaker and tone controls to the middle position, press the f knob for more than two seconds until a beep sounds. Chime Volume The radio may be used to adjust the vehicle's chime level. If the radio can be used to change the volume level of the chime, press and hold the sixth FAV pushbutton with the ignition on and the radio power off. The volume level changes between Normal and Loud. The selected volume level appears on the radio display.
Infotainment System © SEEK ¨ : Press to go to the previous or to the next station. Storing a Radio Station as a Favorite To scan stations, press and hold either arrow for a few seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. Drivers are encouraged to set up their radio station favorites while the vehicle is in P (Park).
7-6 Infotainment System To setup the number of favorites pages: 1. Press MENU to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 4. Press FAV, or let the menu time out, to return to the original main radio screen showing the radio station frequency labels and to begin the process of programming favorites for the chosen amount of numbered pages.
Infotainment System Finding a Category (CAT) Station CAT (Category): The CAT button is used to find XM™ stations when the radio is in the XM mode. To find XM channels within a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category tabs. 3. To navigate through the categories, do one of the following: . Press the CAT button. . Press the s REV or \ FWD button. . Turn the f knob. 4.
7-8 Infotainment System Storing a Radio Station as a Favorite To store a station as a favorite: Drivers are encouraged to set up their radio station favorites while the vehicle is in P (Park). Tune to favorite stations using the presets, favorites button, and steering wheel controls. See Steering Wheel Controls on page 5‑3. 2. Press FAV to display the page where to store the station.
Infotainment System Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. No CAT Info: No category information is available at this time on this channel. The system is working properly. Channel Off Air: This channel is not currently in service. Tune in to another channel. No Information: No text or informational messages are available at this time on this channel. The system is working properly.
7-10 Infotainment System Radio Reception AM Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other.
Infotainment System Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged as long as it is securely attached to the base. If the mast becomes slightly bent, straighten it out by hand. If the mast is badly bent, replace it. Occasionally check to make sure the antenna is tightened to its base. If tightening is required, tighten by hand. Satellite Radio Antenna The XM Satellite Radio antenna is located on the roof of the vehicle.
7-12 Infotainment System BAND: Press to listen to the radio when a CD is playing. The CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary. . . When a CD is in the player the CD icon and a message showing the disc and/or track number displays. If an auxiliary input device is not connected, “No Input Device Found” displays.
Infotainment System CD Messages CHECK DISC: If this message displays and/or the CD comes out, it could be: . It is very hot. When the temperature returns to normal, the CD should play. . The road is very rough. When the road becomes smoother, the CD should play. . The CD is dirty, scratched, wet, or upside down. . The air is very humid. If so, wait about an hour and try again. . There could have been a problem while burning the CD. . The label could be caught in the CD player.
7-14 . . Infotainment System Create a folder structure that makes it easy to find songs while driving. Organize songs by albums using one folder for each album. Each folder or album should contain 18 songs or less. Avoid subfolders. The system can support up to eight subfolders deep, however, keep the total number of folders to a minimum in order to reduce the complexity and confusion in trying to locate a particular folder during playback. . Make sure playlists have a .m3u or .
Infotainment System 7-15 No Folder Order of Play File System and Naming When the CD contains only compressed files, the files are located under the root folder. The next and previous folder functions do not display on a CD that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT. Tracks recorded to the CD-R or CD-RW are played in the following order: The song name that is displayed is the song name that is contained in the ID3 tag.
7-16 Infotainment System Playing an MP3 f (Tune): Turn to select MP3 files on the CD-R or CD-RW currently playing. © SEEK ¨ : Press the left arrow to go to the start of the current MP3 file, if more than ten seconds have played. Press the right arrow to go to the next MP3 file. If either arrow is held or pressed multiple times, the player continues moving backward or forward through MP3 files on the CD.
Infotainment System located below either arrow button. The disc goes to the next or previous artist in alphabetical order. Continue pressing either button until the desired artist is displayed. To change from playback by artist to playback by album, press the pushbutton located below the Sort By label. From the sort screen, push one of the buttons below the album button. Press the pushbutton below the back label to return to the main music navigator screen.
7-18 Infotainment System Phone Bluetooth Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The system can be used while the key is in ON/RUN or ACC/ACCESSORY position. The range of the Bluetooth system can be up to 9.1 m (30 ft.). Not all phones support all functions, and not all phones are guaranteed to work with the in-vehicle Bluetooth system. See www.gm.com/bluetooth for more information on compatible phones.
Infotainment System Pairing Information: . Up to five cell phones can be paired to the in‐vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in‐vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired. . Only one paired cell phone can be connected to the in‐vehicle Bluetooth system at a time. .
7-20 Infotainment System Deleting a Paired Phone Linking to a Different Phone Storing Name Tags 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 2.
Infotainment System 3. Say the complete phone number to be stored at once with no pauses. . . If the system recognizes the number it responds with “OK, Storing” and repeats the phone number. If the system is unsure it recognizes the phone number, it responds with “Store” and repeats the number followed by “Please say yes or no”. If the number is correct, say “Yes”. If the number is not correct, say “No”. The system will ask for the number to be re‐entered. 4.
7-22 Infotainment System 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store . Does that sound OK?”. . . If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu. Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1.
Infotainment System To use the delete all name tags command: 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete all name tags”. The system responds with “You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no.” . Say “Yes” to delete all name tags. . Say “No” to cancel the function and return to the main menu.
7-24 Infotainment System 4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. . . If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time and the system will repeat them. Using the Call Command 1. Press and hold J / 0 for two seconds.
Infotainment System 7-25 Call Waiting Three‐Way Calling Muting a Call Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Three‐Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. 1. While on a call press J / 0 . The system responds with “Ready” followed by a tone.
7-26 Infotainment System Transferring a Call Audio can be transferred between the in‐vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press J / 0 . The system responds with “Ready” followed by a tone. 2. Say “Transfer Call.” The system responds with “Transferring call” and the audio will switch from the vehicle to the cell phone.
Infotainment System 3. Say the number to send. 3. Say the name tag to send. . If the system clearly recognizes the number it responds with “OK, Sending Number” and the dial tones are sent and the call continues. . If the system clearly recognizes the name tag it responds with “OK, Sending ” and the dial tones are sent and the call continues. . If the system is not sure it recognized the number properly, it responds “Dial Number, Please say yes or no?” followed by a tone.
7-28 Infotainment System 2 NOTES
Climate Controls 8-1 Climate Controls Climate Control Systems Climate Control Systems The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature, the climate control system functions as part of the remote start feature. See Remote Keyless Entry (RKE) System Operation on page 2‑3. Climate Control Systems . . . . . . 8-1 Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 8-5 Air Vents Air Vents . . . . .
8-2 Climate Controls A (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. To turn the fan off, turn the left knob all the way counterclockwise. In any setting other than off, the fan runs continuously with the ignition on. There will be some airflow noticeable from the various outlets when driving, even with the fan in the off position. To turn off the air completely, turn the fan to 9 and select the recirculation button.
Climate Controls On hot days, open the windows to let hot inside air escape; then close them. This helps reduce the time it takes for the vehicle to cool down and helps the system to operate more efficiently. For quick cool down on hot days, select the following settings together: H mode. Select ; . Turn the # on. 1. Select 2. 3. 4. Select the coolest temperature and highest fan speed. 5.
8-4 Climate Controls Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger only works when the ignition is in ON/RUN. < (Rear Window Defogger): Press to turn the rear window defogger on or off. An indicator light on the button comes on to show that the rear window is activated. The rear window defogger stays on for approximately 10 minutes after the button is pressed, unless the ignition is turned to ACC/ ACCESSORY or LOCK/OFF.
Climate Controls 8-5 Automatic Climate Control System Automatic Operation The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature, the climate control system functions as part of the remote start feature. See Remote Keyless Entry (RKE) System Operation on page 2‑3. This climate control system automatically maintains the desired temperature inside the vehicle.
8-6 Climate Controls AUTO (Automatic Air Delivery Mode): Turn the air delivery mode knob to AUTO for the system to automatically control the direction of the airflow to help reach the desired inside temperature. The system automatically controls the air inlet to supply the outside air or recirculated inside air needed to heat or cool the vehicle faster. The recirculation button indicator light is lit whenever the recirculation mode is on. Press the outside air button to change to outside air.
Climate Controls When this mode is selected, the system turns the recirculation mode off. Recirculation mode cannot be selected while in floor mode. This is to help prevent window fogging. -(Defog): Clears the windows of fog or moisture. Air is directed to the floor outlets, with some air directed to the windshield and side window outlets. In this mode, the system turns the recirculation mode off and runs the air conditioning compressor unless the outside air is at or below freezing.
8-8 Climate Controls @ (Recirculation): Press to turn on the recirculation mode. An indicator light comes on to show that recirculation is on. This mode recirculates and helps to quickly cool or heat the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. Avoid using the recirculation mode during high periods of humidity and cool outside temperatures since this may result in increased window fogging. If window fogging is experienced, select the defrost mode.
Climate Controls Air Vents Use the louvers located on the air outlets to adjust the airflow. Operation Tips . Clear away any ice, snow, or leaves from the air inlets at the base of the vehicle that may block the flow of air into the vehicle. . Do not use any non-GM approved hood deflectors that could adversely affect the performance of the system. . Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively.
8-10 Climate Controls 3. Unplug both wire cables and remove the glove box. 4. Remove the air filter cover screw. 5. Remove the filter cover and pull out the old air filter. 6. Install the new air filter. 7. Reinstall the air filter cover. Reconnect the wire cabling and re‐install the glove box. See your dealer/retailer if additional assistance is needed.
Driving and Operating Driving and Operating Driving Information Driver Behavior . . . . . . . . . . . . . . . 9-2 Driving Environment . . . . . . . . . . 9-2 Vehicle Design . . . . . . . . . . . . . . . . 9-2 Defensive Driving . . . . . . . . . . . . . 9-3 Drunk Driving . . . . . . . . . . . . . . . . . 9-3 Control of a Vehicle . . . . . . . . . . . 9-4 Braking . . . . . . . . . . . . . . . . . . . . . . . 9-4 Steering . . . . . . . . . . . . . . . . . . . . . . . 9-5 Off-Road Recovery . . . . . . . . . .
9-2 Driving and Operating Driving Information Driver Behavior Whenever we drive, we are taking on an important responsibility. This is true for any motor vehicle — passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle's design all affect how well a vehicle performs. But statistics show that the most important factor, by far, is how we drive.
Driving and Operating Safe driver behavior and understanding the environment in which you will be driving can help avoid a rollover crash in any type of vehicle, including utility vehicles. Defensive Driving Defensive driving means “always expect the unexpected.” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 3‑10. { WARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
9-4 Driving and Operating Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking. Control of a Vehicle The following three systems help to control the vehicle while driving — brakes, steering, and accelerator.
Driving and Operating If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push. Adding non‐dealer/non‐retailer accessories can affect vehicle performance.
9-6 Driving and Operating Steering in Emergencies Off-Road Recovery There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. These problems can be avoided by braking — if you can stop in time. But sometimes you cannot stop in time because there is no room.
Driving and Operating tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway. Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger.
9-8 Driving and Operating Off-Road Driving Vehicles with all‐wheel drive can be used for off‐road driving. Vehicles without all‐wheel drive should not be driven off-road except on a level, solid surface. Many of the vehicle design features that help make the vehicle more responsive on paved roads during poor weather conditions also help make it better suited for off‐road use than conventional passenger vehicles.
Driving and Operating Loading Your Vehicle for Off-Road Driving WARNING (Continued) . { WARNING . . Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks. Unsecured cargo on the load floor can be tossed about when driving over rough terrain. You or your passengers can be struck by flying objects. Secure the cargo properly.
9-10 Driving and Operating . Always carry a litter bag and make sure all refuse is removed from any campsite before leaving. . Take extreme care with open fires (where permitted), camp stoves, and lanterns. . Never park your vehicle over dry grass or other combustible materials that could catch fire from the heat of the vehicle's exhaust system. Traveling to Remote Areas It makes sense to plan your trip, especially when going to a remote area. Know the terrain and plan your route.
Driving and Operating Scanning the Terrain Off-road driving can take you over many different kinds of terrain. Be familiar with the terrain and its many different features. Surface Conditions: Off-roading surfaces can be hard-packed dirt, gravel, rocks, grass, sand, mud, snow, or ice. Each of these surfaces affects the vehicle's steering, acceleration, and braking in different ways.
9-12 Driving and Operating Driving on Hills Approaching a Hill Off-road driving often takes you up, down, or across a hill. Driving safely on hills requires good judgment and an understanding of what the vehicle can and cannot do. There are some hills that simply cannot be driven, no matter how well built the vehicle. When you approach a hill, decide if it is too steep to climb, descend, or cross. Steepness can be hard to judge.
Driving and Operating { WARNING { WARNING Turning or driving across steep hills can be dangerous. You could lose traction, slide sideways, and possibly roll over. You could be seriously injured or killed. When driving up hills, always try to go straight up. . Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to find another route. . Ease up on the speed as you approach the top of the hill. .
9-14 Driving and Operating Things not to do if the vehicle stalls, or is about to stall, when going up a hill: . . Never attempt to prevent a stall by shifting into N (Neutral) to rev-up the engine and regain forward momentum. This will not work. The vehicle can roll backward very quickly and could go out of control. Never try to turn around if about to stall when going up a hill. If the hill is steep enough to stall the vehicle, it is steep enough to cause it to roll over.
Driving and Operating Vehicles are much more likely to stall when going uphill, but if it happens when going downhill: 2. Shift to P (Park) and, while still braking, restart the engine. 3. Shift back to a low gear, release the parking brake, and drive straight down. 4. If the engine will not start, get out and get help. Driving Across an Incline An off-road trail will probably go across the incline of a hill.
9-16 Driving and Operating If you feel the vehicle starting to slide sideways, turn downhill. This should help straighten out the vehicle and prevent the side slipping. The best way to prevent this is to “walk the course” first, so you know what the surface is like before driving it. If the vehicle stalls when crossing an incline, be sure you, and any passengers, get out on the uphill side, even if the door there is harder to open.
Driving and Operating Driving in Water { WARNING Driving through rushing water can be dangerous. Deep water can sweep your vehicle downstream and you and your passengers could drown. If it is only shallow water, it can still wash away the ground from under your tires, and you could lose traction and roll the vehicle over. Do not drive through rushing water. Heavy rain can mean flash flooding, and flood waters demand extreme caution. Find out how deep the water is before driving through it.
9-18 Driving and Operating Driving on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep‐standing or flowing water. { WARNING Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. You could lose control of the vehicle.
Driving and Operating . . Keep your eyes moving — scan the road ahead and to the sides. Check the rearview mirror and vehicle instruments often. Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission. . Going down steep or long hills, shift to a lower gear.
9-20 Driving and Operating Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive with caution, whatever the condition. Accelerate gently so traction is not lost.
Driving and Operating { WARNING Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: . Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. . Check again from time to time to be sure snow does not collect there. .
9-22 Driving and Operating If the Vehicle is Stuck Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. If the vehicle has a traction system, it can often help to free a stuck vehicle. Refer to the vehicle's traction system in the Index. If stuck too severely for the traction system to free the vehicle, turn the traction system off and use the rocking method.
Driving and Operating { WARNING Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle. Tire and Loading Information Label 9-23 positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
9-24 Driving and Operating Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Driving and Operating 9-25 Refer to the vehicle's Tire and Loading Information label for specific information about the vehicle's capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed the vehicle's capacity weight. Example 2 A. Vehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). C. Available Cargo Weight = 113 kg (250 lbs). Example 3 A.
9-26 Driving and Operating Certification Label Label Example A vehicle specific Certification label is attached to the lower area of the center pillar (B-Pillar) on the driver side of the vehicle. The label tells the gross weight capacity of the vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. Never exceed the GVWR for the vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle.
Driving and Operating WARNING (Continued) . . Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. Do not leave an unsecured child restraint in the vehicle. . When you carry something inside the vehicle, secure it whenever you can. . Do not leave a seat folded down unless you need to. Starting and Operating . Avoid making hard stops for the first 200 miles (322 km) or so. During this time the new brake linings are not yet broken in.
9-28 Driving and Operating Ignition Positions LOCK/OFF: This position locks the ignition. It also locks the steering wheel and the transmission. The key can only be removed in LOCK/ OFF. The shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF. The steering can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY. If this doesn't work, the vehicle needs service.
Driving and Operating Retained Accessory Power (RAP) These vehicle accessories may be used for up to 10 minutes after the ignition key is turned to the LOCK position: . Outside Mirror . Power Windows . Sunroof (if equipped) . Radio The outside mirror, power windows and sunroof will function until a door is opened. The radio will function until the driver door is opened. Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position.
9-30 Driving and Operating 2. If the engine does not start after 5‐10 seconds, especially in very cold weather (below −18°C or 0°F), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator.
Driving and Operating { WARNING Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts.
9-32 Driving and Operating Leaving the Vehicle With the Engine Running (Automatic Transmission) { WARNING It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave the vehicle with the engine running.
Driving and Operating Shifting Out of Park The vehicle has an electronic shift lock release system. The shift lock release is designed to: . . If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 10‑74 for more information. Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released.
9-34 Driving and Operating WARNING (Continued) Running the Vehicle While Parked . The vehicle’s exhaust system has been modified, damaged or improperly repaired. It is better not to park with the engine running. But if you ever have to, here are some things to know. . There are holes or openings in the vehicle body from damage or after-market modifications that are not completely sealed.
Driving and Operating { WARNING It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
9-36 Driving and Operating the shift lever button before you can shift from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 9‑33. R (Reverse): Use this gear to back up.
Driving and Operating M (Manual): This position allows you to change gears similar to a manual transmission. If the vehicle has this feature, see Manual Shift Mode. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.
9-38 Driving and Operating Drive Systems Brakes All-Wheel Drive Antilock Brake System (ABS) With this feature, engine power is always sent to all four wheels. It is fully automatic, and adjusts itself as needed for road conditions. When using a compact spare tire on an AWD vehicle, the system automatically detects the compact spare and disables AWD. To restore AWD operation and prevent excessive wear on system, replace the compact spare with a full-size tire as soon as possible.
Driving and Operating Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Parking Brake Braking in Emergencies ABS allows the driver to steer and brake at the same time.
9-40 Driving and Operating Ride Control Systems Traction Control System (TCS) The vehicle has a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that any of the drive wheels are spinning or beginning to lose traction. When this happens, TCS applies the brakes to limit wheel spin and also reduces engine power. The system may be heard or felt while it is working, but this is normal.
Driving and Operating Adding non‐dealer/non‐retailer accessories can affect the vehicle's performance. See Accessories and Modifications on page 10‑3 for more information. The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. 9-41 conditions, the system should always be left on. StabiliTrak can be turned off if needed.
9-42 Driving and Operating StabiliTrak may also turn off automatically if it determines that a problem exists with the system. The TCS/StabiliTrak warning light will be on solid to warn the driver that StabiliTrak is disabled and requires service. If the problem does not clear itself after restarting the vehicle, see your dealer/retailer for service. If cruise control is being used when StabiliTrak activates, the cruise control automatically disengages.
Driving and Operating To set a speed: 1. Press E to turn cruise control on. The indicator light on the button comes on. 2. Get to the speed desired. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: . Move the thumbwheel up toward RES+ and hold it until the vehicle accelerates to the desired speed, and then release the switch. . To increase the speed in small amounts, move the thumbwheel up toward RES+ briefly and then release it.
9-44 Driving and Operating Reducing Speed While Using Cruise Control If the cruise control system is already engaged, . . Move the thumbwheel toward −SET and hold until the desired lower speed is reached, then release it. To slow down in very small amounts, move the thumbwheel toward −SET briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle's speed.
Driving and Operating WARNING (Continued) Do not back the vehicle by only looking at the RVC screen, or use the screen during longer, higher speed backing maneuvers or where there could be cross-traffic. Your judged distances using the screen will differ from actual distances. So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death.
9-46 Driving and Operating Rear Vision Camera Location The camera is located in the rear of the vehicle. The following illustration shows the field of view that the camera provides. A. View displayed by the camera. B. Corner of the rear bumper. When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper.
Driving and Operating . The back of the vehicle is in an accident, the position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your dealer/retailer. The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the video display will turn blue.
9-48 Driving and Operating VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 12‑1. Recommended Fuel If the vehicle has the 3.6L V6 engine (VIN Code 7), use regular unleaded gasoline with a posted octane rating of 87 or higher. For best performance or trailer towing, you could choose to use middle grade 89 octane unleaded gasoline. If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving.
Driving and Operating Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.
9-50 Driving and Operating Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol.
Driving and Operating { WARNING The tethered fuel cap is located behind a hinged fuel door on the driver side of the vehicle. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. To avoid fuel contact on the painted surface of the vehicle when filling the fuel tank, place the tethered cap on the fuel filler door. Fuel can spray out on you if you open the fuel cap too quickly.
9-52 Driving and Operating Filling a Portable Fuel Container { WARNING Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: . Dispense fuel only into approved containers. . Do not fill a container while it is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground.
Driving and Operating towing the vehicle behind another vehicle — such as a motorhome, see Recreational Vehicle Towing on page 10‑78. Driving Characteristics and Towing Tips { WARNING The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured.
9-54 Driving and Operating Driving with a Trailer Towing a trailer requires experience. Get familiar with handling and braking with the added trailer weight. The vehicle is now longer and not as responsive as the vehicle is by itself. Check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires and mirror adjustments.
Driving and Operating Turn Signals When Towing a Trailer The turn signal indicators on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping. When towing a trailer, the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out. Check occasionally to be sure the trailer bulbs are still working.
9-56 Driving and Operating Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: . Start the engine. . Shift into a gear. . Release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks. Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer. See this manual's Maintenance Schedule or Index for more information.
Driving and Operating 9-57 Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options. Vehicle Axle Ratio Max. Trailer Wt. *GCWR 2WD — 2.4L L4 Engine 3.91 680 kg (1,500 lbs) 2 438 kg (5,375 lbs) 2WD — 3.6L V6 Engine 2.77 1 588 kg (3,500 lbs) 3 538 kg (7,800 lbs) AWD — 3.5L V6 Engine 2.77 1 588 kg (3,500 lbs) 3 629 kg (8,000 lbs) AWD — 3.6L V6 Engine 2.
9-58 Driving and Operating proper. If they are not, adjustments might be made by moving some items around in the trailer. If a weight-carrying hitch or a weight-distributing hitch is being used, the trailer tongue (A) should weigh 10‐15 percent of the total loaded trailer weight (B). After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are Trailering may be limited by the vehicle's ability to carry tongue weight.
Driving and Operating Since the rear axle already weighs 1 225 kg (2,700 lbs), adding 578 kg (1,275 lbs) brings the total to 1 803 kg (3,975 lbs). This is very close to, but within the limit for RGAWR as well. The vehicle is set to trailer up to 3 856 kg (8,500 lbs). If the vehicle has many options and there is a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well.
9-60 Driving and Operating Towing Equipment Safety Chains Hitches Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Always leave just enough slack so the rig can turn. Never allow safety chains to drag on the ground. It is important to have the correct hitch equipment.
Driving and Operating Conversions and Add-Ons Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/ retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle battery, even if the vehicle is not operating. The vehicle has an airbag system.
9-62 Driving and Operating 2 NOTES
Vehicle Care Vehicle Care General Information General Information . . . . . . . . . . California Proposition 65 Warning . . . . . . . . . . . . . . . . . California Perchlorate Materials Requirements . . . . Accessories and Modifications . . . . . . . . . . . . . . . 10-2 10-2 10-3 10-3 Vehicle Checks Doing Your Own Service Work . . . . . . . . . . . . . . . 10-4 Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Engine Compartment Overview . . . . . . . . . . . . . . . . . . . 10-6 Engine Oil . .
10-2 Vehicle Care Different Size Tires and Wheels . . . . . . . . . . . . . . . . . . . 10-61 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 10-62 Wheel Alignment and Tire Balance . . . . . . . . . . . . . . 10-63 Wheel Replacement . . . . . . . . 10-64 Tire Chains . . . . . . . . . . . . . . . . . 10-64 If a Tire Goes Flat . . . . . . . . . . 10-65 Tire Changing . . . . . . . . . . . . . . 10-67 Compact Spare Tire . . . . . . . . 10-73 Jump Starting Jump Starting . . . . . . . . . .
Vehicle Care California Perchlorate Materials Requirements Accessories and Modifications Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate.
10-4 Vehicle Care Vehicle Checks Doing Your Own Service Work { WARNING You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. . Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task. (Continued) WARNING (Continued) . Be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused.
Vehicle Care Hood To open the hood: 1. Pull the handle with this symbol on it. It is located under the instrument panel on the driver side of the vehicle. 2. Then go to the front of the vehicle and lift up on the secondary hood release lever. 3. Lift the hood. Before closing the hood, be sure all the filler caps are on properly. Then pull the hood down and close it firmly.
10-6 Vehicle Care Engine Compartment Overview 2.4L L4 Engine D. Engine Oil Fill Cap (Out of View). See “When to Add Engine Oil” under Engine Oil on page 10‑8. E. Brake Fluid Reservoir. See Brakes on page 10‑23. F. Engine Coolant Surge Tank. See “Checking Coolant” under Engine Coolant on page 10‑15. G. Remote Positive (+) Terminal. See Jump Starting on page 10‑74. H. See Engine Compartment Fuse Block on page 10‑38. I. A. See Engine Air Cleaner/Filter on page 10‑12. B.
Vehicle Care 3.5L V6 Engine (3.6L V6 Engine similar) 10-7 E. Engine Oil Dipstick (Out of View). See “Checking Engine Oil” under Engine Oil on page 10‑8. F. Automatic Transmission Fluid Dipstick (Out of View). See “Checking the Fluid Level” under Automatic Transmission Fluid on page 10‑12. G. Brake Fluid Reservoir (Out of View). See Brakes on page 10‑23. H. Engine Coolant Recovery Tank. See Cooling System on page 10‑14. I. A. See Engine Air Cleaner/Filter on page 10‑12. B.
10-8 Vehicle Care Engine Oil When to Add Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10‑6 for the location of the engine oil dipstick. 1. Turn off the engine and give the oil several minutes to drain back into the oil pan.
Vehicle Care What Kind of Engine Oil to Use . GM6094M Use only an oil that meets GM Standard GM6094M. Look for three things: . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container.
10-10 Vehicle Care Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM standards are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty. Engine Oil Life System When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter.
Vehicle Care After changing the engine oil, reset the system: The oil life system can also be reset as follows: 1. Press the DIC vehicle information button to display OIL LIFE REMAINING on the DIC. See Driver Information Center (DIC) on page 5‑25 and Engine Oil Messages on page 5‑33. 1. Turn the ignition key to ON/RUN with the engine off. 2. Press the DIC Set/Reset button for during 5 seconds to reset the oil life at 100%.
10-12 Vehicle Care Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take your vehicle to the dealer/retailer and have it repaired as soon as possible. For the 2.4L, 3.5L and 3.6L engines, the transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature.
Vehicle Care To inspect or replace the engine air cleaner/filter, do the following: 5. Remove the air cleaner cover assembly and air filter element. 6. Inspect or replace the air filter element. If the air filter element is dirty, you should replace it. If it is only dusty, it may be cleaned by blowing compressed air through it from the clean side. Make sure you are away from the engine compartment when cleaning the air filter with compressed air. 1. Remove the clamp on the air duct hose. 2.
10-14 Vehicle Care Cooling System When it is safe to lift the hood: { WARNING { WARNING An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. If the coolant inside the coolant surge tank is hot, do not do anything else until it cools down.
Vehicle Care Notice: Engine damage from running the engine without coolant is not covered by the warranty. Notice: Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner, at 50 000 km (30,000 miles) or 24 months, whichever occurs first. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL® (silicate-free) coolant in the vehicle.
10-16 Vehicle Care What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. { WARNING Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture.
Vehicle Care Checking Coolant { WARNING Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the surge tank pressure cap — even a little — when the engine and radiator are hot. The surge tank is located on the driver side of the engine compartment. See Engine Compartment Overview on page 10‑6 for more information on location. The vehicle must be on a level surface.
10-18 Vehicle Care How to Add Coolant to the Coolant Surge Tank Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If you have not found a problem yet, check to see if coolant is visible in the surge tank.
Vehicle Care { WARNING You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one-quarter of a turn. If you hear a hiss, wait for that to stop.
10-20 Vehicle Care Engine Overheating There is a coolant temperature warning light on your vehicle's instrument panel. See Engine Coolant Temperature Warning Light on page 5‑21. If Steam Is Coming From Your Engine { WARNING Steam from an overheated engine can cause serious injury, even if the hood is opened just a little. Stay away from the engine if steam is seen or heard coming from it. Just turn it off and get everyone away from the vehicle (Continued) WARNING (Continued) until it cools down.
Vehicle Care If the overheat warning is no longer on, the vehicle can be driven. Just to be safe, drive slower for about ten minutes. If the warning does not come back on, drive normally. If the warning continues and the vehicle is not stopped, pull over, stop, and park the vehicle right away. If there is still no sign of steam, idle the engine for three minutes while parked. If the warning continues, turn off the engine and get everyone out of the vehicle until it cools down.
10-22 Vehicle Care What to Use Washer Fluid To determine what kind of fluid to use, Recommended Fluids and Lubricants on page 11‑7. Always use the proper fluid. What to Use Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty. Always use the correct fluid listed in Recommended Fluids and Lubricants on page 11‑7. When you need windshield or rear window washer fluid, be sure to read the manufacturer's instructions before use.
Vehicle Care Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly. { WARNING The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced.
10-24 Vehicle Care Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10‑6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: . The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up. .
Vehicle Care Notice: . . Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. If brake fluid is spilled on the vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle.
10-26 Vehicle Care All-Wheel Drive How to Check Lubricant It is recommended that the all-wheel drive lubricants be checked and filled by the dealer/retailer. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 11‑7. Transfer Case When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 11‑2.
Vehicle Care How to Check Lubricant A fluid loss could indicate a problem; check and have it repaired, if needed. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 11‑7. Starter Switch Check { WARNING AWD Differential Case A. Fill Plug B. Drain Plug To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, you'll need to add some lubricant.
10-28 Vehicle Care Automatic Transmission Shift Lock Control System Check { WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2. Firmly apply the parking brake. See Parking Brake on page 9‑39. Be ready to apply the regular brake immediately if the vehicle begins to move. 3.
Vehicle Care Park Brake and P (Park) Mechanism Check { WARNING When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. . .
10-30 Vehicle Care To replace the rear wiper blade: Headlamp Aiming The headlamp aiming system has been preset at the factory. If the vehicle is damaged in an accident, the aim of the headlamps may be affected and adjustment may be necessary. It is recommended that a dealer/ retailer adjust the headlamps. To re-aim the headlamps yourself, use the following procedure. 2. Push the release lever (B) to disengage the hook and push the wiper arm (A) out of the blade (C). 1.
Vehicle Care . The vehicle should be placed so it is perpendicular to the wall or other flat surface. . The vehicle should not have any snow, ice, or mud on it. . The vehicle should be fully assembled and all other work stopped while headlamp aiming is being performed. . The vehicle should be normally loaded with a full tank of fuel and one person or 75 kg (160 lbs) sitting on the driver's seat. . To adjust the vertical aim, do the following: 1. Open the hood.
10-32 Vehicle Care Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp. 6. Turn on the low-beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being adjusted. This allows only the beam of light from the headlamp being adjusted to be seen on the flat surface. 7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly.
Vehicle Care Bulb Replacement Headlamps For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑36. To replace one of the headlamp bulbs, use the following procedure. To replace the parking/turn signal lamp bulb, see Front Turn Signal and Parking Lamps on page 10‑34. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs { WARNING Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
10-34 Vehicle Care Front Turn Signal and Parking Lamps To replace a front turn signal or parking lamp bulb: 1. Follow Steps 1 through 6 under Headlamps on page 10‑33 to access the front turn signal or parking lamp. 3. Pull the bulb out of the bulb socket assembly. 4. Push the new bulb into the bulb socket assembly. 5. Insert the bulb assembly into the headlamp assembly. 6. Turn the bulb assembly clockwise until seated. 7. Reverse the steps to reinstall the headlamp assembly. 7.
Vehicle Care Taillamps, Turn Signal, Stoplamps, and Back-Up Lamps 1. Open the liftgate. 10-35 4. Turn the bulb socket being replaced counterclockwise to disconnect it. 5. Pull the bulb out of the bulb socket. To replace one of these bulbs: 6. Push the new bulb into the bulb socket. 7. Reverse Steps 2 through 4 to reinstall the taillamp assembly. 2. Remove the two screws holding in the taillamp assembly. A. Taillamp/Stoplamp B. Turn Signal Lamp C. Back-up Lamp 3.
10-36 Vehicle Care License Plate Lamp To replace one of these bulbs: 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket. 1. Remove the two screws holding each of the license plate lamps to the fascia. 4. Push the new bulb into the bulb socket and turn it clockwise to lock it into place. 5. Push and turn the license plate back through the fascia opening. 6. Reinstall the two screws holding the license plate lamps to the fascia.
Vehicle Care Electrical System Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect the following in the vehicle: . Headlamp Wiring .
10-38 Vehicle Care Engine Compartment Fuse Block The engine compartment fuse block is located on the driver side of the engine compartment, near the battery. Notice: Spilling liquid on any electrical components on the vehicle may damage it. Always keep the covers on any electrical component.
Vehicle Care Fuses Usage Fuses Usage Air Conditioning Compressor Engine Control Module A/C CLTCH ENG-3 Engine 3 BLWR MTR Blower Motor ENG-2 Engine 2 AMP ENG-1 Engine 1 HORN ECM HYBRID BEC RUN S/ROOF HTD/SEAT Not Used Sunroof Module Heated Seat Control Module Body Control Module STRTR Starter Motor Windshield Wiper All-Wheel Drive 4WD/ESCM System ABS Antilock Brake System Module Horn Antilock Brake System Module TRLR T/LAMP Usage Trailer Parking Lamps Passenger Side HDLP HI LT High-
10-40 Vehicle Care Relays Usage FAN MAIN RLY Cooling Fan Main Relay FAN CTRL RLY Cooling Fan Control Relay FAN AUX RLY Cooling Fan Auxiliary Relay PWR/ TRN RLY Engine Control Module/CAM, Canister, Injectors, Electronic Throttle Control Relay STRTR RLY Starter Relay RUN RLY Run Relay A/C Air Conditioning CLTCH RLY Compressor Relay WPR SPD RLY Windshield Wiper Speed Relay Relays Usage HORN RLY Horn Relay WPR Windshield Wiper CNTRL RLY Control Relay T/LAMP RLY Parking Lamp Relay HDLP HI RLY
Vehicle Care Fuses Usage CIGAR Cigarette Lighter ECM/TCM Fuses Usage PWR SEAT Power Seat PASS P/WIN Passenger Side Power Window Fuses Usage DRIV P/WIN Driver Side Power Window S/ROOF 10-41 Engine Control Module (ECM)/ Transmission Control Module (TCM) FSCM Fuel Storage Control Module ISRVM Inside Rearview Mirror CLUSTER Instrument Panel Cluster AIR BAG Airbag System OSRVM Outside Rearview Mirror KEY CAP Key Capture Solenoid WHL S/W Steering Wheel Switch Sunroof Module
10-42 Vehicle Care Fuses F/DR LCK APO2 Usage Front Driver Door Lock Accessory Power Outlet 2 Body Control BCM (VB3) Module (BCM) (VB3) Fuses Usage BCM (VB7) Body Control Module (VB7) IGN SW Ignition Switch AIR BAG Air Bag System WASHER Washer Pump Door Lock APO1 Accessory Power Outlet 1 BCM (VB6) Body Control Module (VB6) FSCM Fuel Storage Control Module BCM (VB4) Body Control Module (VB4) BCM (VB5) Body Control Module (VB5) DR LCK TRL AIRCON AUDIO Trailer RR CLR Rear Closure
Vehicle Care Wheels and Tires Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. { WARNING Poorly maintained and improperly used tires are dangerous. . . Overloading your tires can cause overheating as a result of too much flexing. You could have an air-out and a serious accident.
10-44 Vehicle Care Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P‐Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. the U.S.
Vehicle Care traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10‑62 . (G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. Compact Spare Tire Example (A) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.
10-46 Vehicle Care (F) Tire Size : A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall.
Vehicle Care certified to carry. The speed rating is the maximum speed a tire is certified to carry a load. Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in psi (pounds per square inch) or kPa (kilopascal). Accessory Weight: This means the combined weight of optional accessories.
10-48 Vehicle Care GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑22 . GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑22 . Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles.
Vehicle Care Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided.
10-50 Vehicle Care Tire Pressure Tires need the correct amount of air pressure to operate effectively. If your tires have too much air (over‐inflation), you can get the following: . Unusual wear Notice: Do not let anyone tell . Poor handling you that under‐inflation or over‐inflation is all right. It is not. If your tires do not have enough air (under‐inflation), you can get the following: . Rough ride . Needless damage from road hazards . Too much flexing . Too much heat .
Vehicle Care When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. The compact spare should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 10‑73 . How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under‐inflated.
10-52 Vehicle Care Tire Pressure for High-Speed Operation { WARNING Driving at high speeds, 160 km/h (100 mph) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for high speed operation.
Vehicle Care As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under‐inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under‐inflated tire causes the tire to overheat and can lead to tire failure.
10-54 Vehicle Care Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the vehicle's tires and transmit the tire pressure readings to a receiver located in the vehicle.
Vehicle Care TPMS Malfunction Light The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. The TPMS malfunction light comes on at each ignition cycle until the problem is corrected. Some of the conditions that can cause the malfunction light to come on are: .
10-56 Vehicle Care TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate the vehicle's tires, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched, to the tire/wheel positions, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool.
Vehicle Care 8. Proceed to the driver side rear tire. The driver side rear turn signal lamp comes on. Repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. 9. Turn the ignition switch to LOCK/OFF. 10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label. 11.
10-58 Vehicle Care Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Tire Pressure on page 10‑50 and Vehicle Load Limits on page 9‑22 . Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑54 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2 .
Vehicle Care The vehicle needs new tires if any of the following statements are true: . You can see the indicators at three or more places around the tire. . You can see cord or fabric showing through the tire's rubber. . The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. . The tire has a bump, bulge, or split. . The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.
10-60 Vehicle Care GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection on page 10‑57 and Tire Rotation on page 10‑57 for information on proper tire rotation. { WARNING { WARNING Mixing tires could cause you to lose control while driving.
Vehicle Care Vehicles that have a tire pressure monitoring system could give an inaccurate low‐pressure warning if non‐TPC Spec rated tires are installed on your vehicle. Non‐TPC Spec rated tires may give a low‐pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 10‑52 . Your vehicle's original equipment tires are listed on the Tire and Loading Information Label.
10-62 Vehicle Care Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States.
Vehicle Care Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
10-64 Vehicle Care Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer/retailer if any of these conditions exist. Your dealer/retailer will know the kind of wheel you need.
Vehicle Care WARNING (Continued) suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions. Follow that manufacturer's instructions.
10-66 Vehicle Care If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3. { WARNING Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: WARNING (Continued) 3.
Vehicle Care 10-67 Tire Changing Removing the Spare Tire and Tools To access the spare tire: 1. Open the liftgate. 4. Remove the tire protector foam. 5. Remove the wheel retainer bolt holding down the spare tire by turning it counterclockwise. 6. Remove the compact spare tire. See Compact Spare Tire on page 10‑73 for more information. 2. Push the levers on the load floor. 3. Lift the load floor and hang the hook to the tailgate opening.
10-68 Vehicle Care The tools are located between the compact spare tire and the liftgate. To access the tools: 3. Remove the straps holding the bag containing the wheel wrench and extension jack handle. Remove the wheel wrench and extension jack handle from the bag. Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See If a Tire Goes Flat on page 10‑65 for more information. The tools you will be using include: A. Tool Bag B. Wing-bolt C. Jack 1.
Vehicle Care 10-69 { WARNING Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { WARNING 4. Position the lift head at the jack location nearest the flat tire. Make sure all of the jack lift head is touching the jacking flange under the body. Do not place the jack under a body panel. The lower body panel has an arrow to aid in locating the jacking location. 5.
10-70 Vehicle Care { WARNING { WARNING Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.
Vehicle Care WARNING (Continued) to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12‑2 for original equipment wheel nut torque specifications. 13. Tighten the wheel nuts firmly in a crisscross sequence, as shown. { WARNING Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off.
10-72 Vehicle Care Storing a Flat or Spare Tire and Tools { WARNING Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. To store the flat or spare tire and tools, do the following: 2. Install the jack between the back of the trunk and the compact spare tire and secure with the wing bolt. 1.
Vehicle Care 5. Remove the disk (A) from the retainer bolt. Turn the disk (A) over and place it back on the retainer bolt. Return the disk back to its original position after removing the flat tire from the spare tire compartment and before storing the spare tire. 6. Place the wheel retainer bolt onto the wheel stow rod and tighten by turning it clockwise. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as possible.
10-74 Vehicle Care Jump Starting If the vehicle battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { WARNING Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you. . They contain gas that can explode or ignite. . They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Vehicle Care 4. Open the hood on the other vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. Open the hood on your vehicle and find the remote positive (+) and remote negative (−) jump starting terminals. of the vehicle, on the underhood fuse block. See Engine Compartment Overview on page 10‑6 for more information on location. To uncover the remote positive (+) terminal, press the tab on the bottom of the fuse block and lift the cover up.
10-76 Vehicle Care { WARNING Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could also be damaged. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
Vehicle Care 10. Now start the vehicle with the good battery and run the engine for a while. To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 11. Press the unlock symbol on the remote keyless entry transmitter to disarm your security system, if equipped. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 12. Try to start the vehicle that had the dead battery.
10-78 Vehicle Care Towing Towing the Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes — such as behind a motorhome, see Recreational Vehicle Towing following.
Vehicle Care Dinghy Towing 3. Shift the transmission to N (Neutral). Front-wheel‐drive and all-wheel-drive vehicles may be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. For other towing options, see “Dolly Towing” following in this section. For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes.
10-80 Vehicle Care Notice: If the vehicle is towed without performing each of the steps listed under “Dinghy Towing,” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle. Notice: If the vehicle has a four‐speed automatic transmission, it can be dinghy towed from the front for unlimited miles at 105 km/h (65 mph). The vehicle could be damaged If 105 km/h (65 mph) is exceeded while towing the vehicle.
Vehicle Care Dolly Towing (Front-Wheel‐Drive Vehicles) 10-81 5. Remove the key from the ignition. 6. Secure the vehicle to the dolly. 7. Release the parking brake. Towing the Vehicle From the Rear To tow the vehicle from the front with the rear wheels on the ground, do the following: 1. Put the front wheels on a dolly. 2. Move the shift lever to P (Park). 3. Set the parking brake. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.
10-82 Vehicle Care Appearance Care Exterior Care Cleaning Exterior Lamps/ Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing the Vehicle” later in this section. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.
Vehicle Care Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty. Do not use cleaning agents that are petroleum based or that contain acid or abrasives, as they can damage the paint, metal or plastic on the vehicle.
10-84 Vehicle Care Aluminum Wheels Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the vehicle's chrome with soap and water after exposure.
Vehicle Care Tires Finish Damage Use a stiff brush with tire cleaner to clean the tires. Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
10-86 Vehicle Care Interior Care The vehicle's interior will continue to look its best if it is cleaned often. Dust and dirt can accumulate on the upholstery and cause damage to the carpet, fabric, leather, and plastic surfaces. Stains should be removed quickly as extreme heat could cause them to set rapidly. Lighter colored interiors may require more frequent cleaning. Newspapers and garments that can transfer color to home furnishings can also transfer color to the vehicle's interior.
Vehicle Care . Use only mild, neutral-pH soaps. Avoid laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per 3.78 L (1 gal) of water is a good guide. . Do not heavily saturate the upholstery while cleaning. . Damage to the vehicle's interior may result from the use of many organic solvents such as naptha, alcohol, etc.
10-88 Vehicle Care Leather To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat, steam, or spot lifters or spot removers, or shoe polish on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of the leather and are not recommended.
Service and Maintenance Service and Maintenance General Information General Information . . . . . . . . . . 11-1 Scheduled Maintenance Scheduled Maintenance . . . . . 11-2 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . 11-7 Maintenance Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 11-9 Maintenance Records Maintenance Records . . . . . .
11-2 Service and Maintenance { WARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury. Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer/ retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 10‑4. At your General Motors dealer/ retailer, you can be certain that you will receive the highest level of service available.
Service and Maintenance life system whenever the oil is changed. See Engine Oil Life System on page 10‑10. . When the change engine oil light displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: . . . Maintenance I . Change engine oil and filter. See Engine Oil on page 10‑8. An Emission Control Service. .
11-4 . . . . Service and Maintenance Body hinges and latches, key lock cylinders, folding seat hardware, and sunroof (if equipped) lubrication. See Recommended Fluids and Lubricants on page 11‑7. More frequent lubrication may be required when vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer, seal better, and not stick or squeak. Restraint system component check. See Safety System Check on page 3‑23.
Service and Maintenance First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks. First Engine Oil Change After Every 80 000 km/50,000 Miles . . . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 10‑12.
11-6 Service and Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • Tire inflation pressures check. • • Tire wear inspection. • • Rotate tires. • • Fluids visual leak check. • • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). • • Brake system inspection. • • Steering and suspension inspection.
Service and Maintenance 11-7 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Engine Oil Engine Coolant Hydraulic Brake System Windshield Washer Hydraulic Power Steering System Parking Brake Cable Guides Automatic Transmission Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for the vehicle's engine, see Engine Oil on page 10‑8.
11-8 Service and Maintenance Usage Key Lock Cylinders Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and Release Pawl Fluid/Lubricant Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Hood, Liftgate Door, and Rear Folding Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Seat Hinges Canada 10953474).
Service and Maintenance 11-9 Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your retailer. Part GM Part Number ACDelco Part Number 96815102 — 2.4L L4 Engine 12605566 PF457G 3.5L V6 Engine 89017342 PF61 3.6L V6 Engine 89017524 PF48 19130294 — 2.4L L4 Engine 12625058 41-103 3.5L V6 Engine 12591131 41-100 3.6L V6 Engine 12622561 41-109 Driver Side – 60.0 cm (24.0 in) 25925618 — Passenger Side – 40.
11-10 Service and Maintenance Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts.
Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 11-11
11-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed
Technical Data Technical Data Vehicle Identification Vehicle Identification Vehicle Identification Number (VIN) Vehicle Identification Number (VIN) . . . . . . . . . . . . . . 12-1 Service Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . 12-1 Vehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . . 12-4 This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle.
12-2 Technical Data Vehicle Data Capacities and Specifications Application Air Conditioning Refrigerant R134a Capacities Metric English For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information. Engine Cooling System 2.4L L4 Engine 8.5 L 9.0 qt 3.5L V6 Engine 10.4 L 11.0 qt 3.6L V6 Engine 10.9 L 11.5 qt 2.4L L4 Engine 4.7 L 5.0 qt 3.5L V6 Engine 3.8 L 4.0 qt 3.6L V6 Engine 5.
Technical Data Capacities Application Metric English All Wheel Drive 63.0 L 16.7 gal Front Wheel Drive 73.0 L 19.2 gal Four-Speed Automatic (Bottom Pan Removal) 6.5 L 6.9 qt Six-Speed Automatic (Drain and Refill) 9.0 L 9.5 qt 140 Y 100 ft lb Fuel Tank Transmission Fluid* Wheel Nut Torque *See Automatic Transmission Fluid on page 10‑12 for information on checking fluid level. All capacities are approximate.
12-4 Technical Data Engine Drive Belt Routing 3.5L V6 (LZ4) Engine 2.4L L4 (LE5) Engine 3.
Customer Information Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 13-1 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . . . 13-4 Customer Assistance for Text Telephone (TTY) Users . . . . . 13-4 Online Owner Center . . . . . . . . 13-5 GM Mobility Reimbursement Program . . . . . . . . . . . . . . . . . . . . 13-5 Roadside Assistance Program . . . . . . . . . . . . . . . . . . . . 13-6 Scheduling Service Appointments . . . . .
13-2 Customer Information STEP TWO : Should you need additional assistance, in the U.S., contact the Saturn Customer Assistance Center by calling 1‐800‐553‐6000. In Canada, call the Saturn Customer Communication Centre at 1-800-263-1999. A Saturn Customer Assistance Center team member will handle your call and assist in providing product and warranty information, the nearest retailer location, roadside assistance, brochures, literature and discuss any concerns you may have.
Customer Information Contact the BBB Auto Line Program by using the toll-free telephone number or by writing them at the following address: BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800 Arlington, VA 22203-1838 Telephone: 1-800-955-5100 dr.bbb.org/goauto This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage and other factors.
13-4 Customer Information Customer Assistance Offices Saturn encourages customers to call the toll-free number for assistance. If a customer wishes to write to Saturn, the letter should be addressed to: Saturn Customer Assistance Center P.O. Box 33173 Detroit, MI 48232-5173 1-800-553-6000 1-800-833-6000 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-553-6000 In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd.
Customer Information Online Owner Center Other Helpful Links: Online Owner Center (U.S.) — www.gmownercenter.com/ saturn Saturn Merchandise — www.saturncollection.com Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records . Find Saturn retailers for service nationwide . Exclusive privileges and offers . Recall notices for your specific vehicle .
13-6 Customer Information Roadside Assistance Program . Odometer reading, Vehicle Identification Number (VIN), and delivery date of the vehicle claims are made too often, or the same type of claim is made many times. For U.S. purchased vehicles, call 1-800-553-6000; (Text Telephone (TTY): 1-800-889-2438). . Description of the problem Services Provided For Canadian purchased vehicles, call 1-800-268-6800. Services are provided up to 5 years/ 100,000 miles (160 000 km), whichever comes first.
Customer Information . . Flat Tire Change: Service is provided to change a flat tire with the spare tire. The spare tire, if equipped, must be in good condition and properly inflated. It is the owner's responsibility for the repair or replacement of the tire if it is not covered by the warranty. Services Specific to Canadian Purchased Vehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted.
13-8 Customer Information Scheduling Service Appointments Courtesy Transportation Program When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/ retailer can help minimize your inconvenience.
Customer Information Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the retailer's shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by Saturn for shuttle service. In addition, for U.S. customers, should you arrange transportation through a friend or relative, limited reimbursement for reasonable fuel expenses may be available.
13-10 Customer Information Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle's resale value, and safety performance can be compromised in subsequent collisions.
Customer Information Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts. Some insurance companies will not specify aftermarket collision parts.
13-12 Customer Information Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts.
Customer Information Owner Publications Information on how to obtain product bulletins and as described below is applicable only in the fifty U.S. states and the District of Columbia, and only for cars and light trucks with a Gross Vehicle Weight Rating (GVWR) less than 10,000 pounds (4 536 kg). Copies of individual bulletins are also at your participating Saturn retailer. You can ask to see them.
13-14 Customer Information To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA 1200 New Jersey Avenue, S.E. Washington D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Customer Information Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
13-16 Customer Information GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office; as part of GM's defense of litigation through the discovery process; or, as required by law.
INDEX A Accessories and Modifications . . . . . . . . . . . . . . . . . 10-3 Accessory Power . . . . . . . . . . . . . . 9-29 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . 9-61 Adding Equipment to the Airbag-Equipped Vehicle . . . . . 3-40 Adjustments Lumbar, Front Seats . . . . . . . . . . . 3-5 Air Cleaner/Filter, Engine . . . . . 10-12 Air Filter, Passenger Compartment . . . . . . . . . . . . . . . . . 8-9 Air Vents . . . . . . . . . . . . . . . . . . . . . . .
i-2 INDEX B Battery . . . . . . . . . . . . . . . . . . . . . . . 10-25 Jump Starting . . . . . . . . . . . . . . . 10-74 Load Management . . . . . . . . . . . . . 6-6 Power Protection . . . . . . . . . . . . . . 6-6 Voltage and Charging Messages . . . . . . . . . . . . . . . . . . .5-31 Blade Replacement, Wiper . . . 10-29 Bluetooth . . . . . . . . . . . . . . . . . . . . . . 7-18 Brakes . . . . . . . . . . . . . . . . . . . . . . . . 10-23 Antilock . . . . . . . . . . . . . . . . . . . . . . .
INDEX Cleaning Exterior Care . . . . . . . . . . . . . . . 10-82 Interior Care . . . . . . . . . . . . . . . . 10-86 Climate Control Systems . . . . . . . 8-1 Automatic . . . . . . . . . . . . . . . . . . . . . . 8-5 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Cluster, IP . . . . . . . . . . . . . . . . . . . . . 5-10 Collision Damage Repair . . . . . 13-10 Compact Spare Tire . . . . . . . . . . 10-73 Compass . . . . . . . . . . . . . . . . . . . . . . . 5-5 Compass Messages . . . . . .
i-4 INDEX Driving (cont.) Off-Road Recovery . . . . . . . . . . . . 9-6 Vehicle Load Limits . . . . . . . . . . .9-22 Winter . . . . . . . . . . . . . . . . . . . . . . . .9-20 Driving for Better Fuel Economy . . . . . . . . . . . . . . . . . . . . . 1-19 E Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . . 9-61 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-38 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . .
INDEX Fuel (cont.) Gage . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Gasoline Specifications . . . . . . .9-48 Low Fuel Warning Light . . . . . . .5-23 Recommended . . . . . . . . . . . . . . .9-48 Requirements, California . . . . .9-48 System Messages . . . . . . . . . . . .5-34 Fuel Economy Driving for Better . . . . . . . . . . . . .1-19 Fuses Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-38 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . .
i-6 INDEX I L Ignition Positions . . . . . . . . . . . . . . 9-28 Ignition Transmission Lock Check . . . . . . . . . . . . . . . . . . . . . . . 10-28 Illumination Control . . . . . . . . . . . . . 6-5 Immobilizer . . . . . . . . . . . . . . . . . . . . 2-10 Infants and Young Children, Restraints . . . . . . . . . . . . . . . . . . . . 3-44 Instrument Cluster . . . . . . . . . . . . . 5-10 Instrument Panel . . . . . . . . . . . . . . . 6-5 Storage Area . . . . . . . . . . . . . . . . . .
INDEX Locks Automatic Door . . . . . . . . . . . . . . . . 2-7 Delayed Locking . . . . . . . . . . . . . . . 2-7 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Lockout Protection . . . . . . . . . . . . . 2-7 Power Door . . . . . . . . . . . . . . . . . . . . 2-6 Safety . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Loss of Control . . . . . . . . . . . . . . . . . 9-7 Low Fuel Warning Light . . . . . . . . 5-23 Low Washer Fluid Warning Light . . . . . . . . . . . . . . . . . . . . .
i-8 INDEX Oil Change Engine Oil Light . . . . . .5-22 Engine . . . . . . . . . . . . . . . . . . . . . . . .10-8 Engine Oil Life System . . . . . 10-10 Messages . . . . . . . . . . . . . . . . . . . .5-33 Pressure Light . . . . . . . . . . . . . . . .5-22 Older Children, Restraints . . . . . 3-42 Online Owner Center . . . . . . . . . . 13-5 OnStar® System . . . . . . . . . . . . . . . 1-20 Operation, Infotainment System . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Outlets Power . . . . . . . . . .
INDEX Records Maintenance . . . . . . . . . . . . . . . . .11-10 Recreational Vehicle Towing . . . . . . . . . . . . . . . . . . . . . . 10-78 Reduced Engine Power Light . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 Reimbursement Program, GM Mobility . . . . . . . . . . . . . . . . . . 13-5 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . 2-2, 2-3 Remote Vehicle Start . . . . . . . . . . . 2-4 Replacement Bulbs . . . . . . . . . . . 10-36 Replacement Parts Airbags . . . . . . . . . . . .
i-10 INDEX Service Accessories and Modifications . . . . . . . . . . . . . . . .10-3 Doing Your Own Work . . . . . . . .10-4 Engine Soon Lamp . . . . . . . . . . .5-15 Maintenance Records . . . . . . .11-10 Maintenance, General Information . . . . . . . . . . . . . . . . . . 11-1 Parts Identification Label . . . . .12-1 Publications Ordering Information . . . . . . . . . . . . . . . . 13-12 Scheduling Appointments . . . . .13-8 Vehicle Messages . . . . . . . . . . . .5-37 Vehicle Soon Light . . . . . . .
INDEX Tires (cont.) Messages . . . . . . . . . . . . . . . . . . . .5-37 Pressure . . . . . . . . . . . . . . . . . . . . 10-52 Pressure Light . . . . . . . . . . . . . . . .5-21 Pressure Monitor System . . . 10-52 Rotation . . . . . . . . . . . . . . . . . . . . 10-57 Sidewall Labeling . . . . . . . . . . . 10-44 Terminology and Definitions . . . . . . . . . . . . . . . . . 10-47 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . 10-62 Wheel Alignment and Tire Balance . . . . . . . . . . .
i-12 INDEX W Warning Lights, Gages, and Indicators . . . . . . . . . . . . . . . . . . . . . 5-9 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . iv Cautions and Danger . . . . . . . . . . . .iv Hazard Flashers . . . . . . . . . . . . . . . 6-3 Washer Fluid . . . . . . . . . . . . . . . . . 10-22 Washer Fluid, Low Warning Light . . . . . . . . . . . . . . . . . . . . . . . . . 5-24 Wheels Alignment and Tire Balance . . . . . . . . . . . . . . . . . . . 10-63 Different Size . . . . . . . . . . .
