HDMI-SPL-2201C HDMI-SPL-2202C HDMI 1.
Safety and Notice The HDMI-SPL-2201C& HDMI-SPL-2202C 1x2 HDMI 1.3 over Single CAT5 Splitter has been tested for conformity to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the HDMI-SPL-2201C & HDMI-SPL-2202C should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. z Follow all instructions and warnings marked on this unit.
Introduction The 1x2 HDMI 1.3 over Single CAT5 Splitter provides the most flexible solution by which the high definition video and high quality audio can be transmitted to different locations over a long distance. The devices are cascadable, allowing you to extend HDMI or DVI compliant displays almost anywhere.
Features z State-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and reliability z HDMI 1.
Technical Specifications and Package Content Model Name Technical Role of usage HDMI compliance HDCP compliance Video bandwidth Video support Transmission Audio support Signal equalization Input TMDS signal Input DDC signal ESD protection PCB stack-up Input Output HDMI connector RJ-45 connector 3.
Panel Descriptions HDMI-SPL-2201C 1x2 HDMI 1.3 over Single CAT5 Splitter 1 2 3 4 7 5 6 1. Input signal format indicator [bright: HDMI signal, dim: DVI signal] 2. DIP switch [see table below] 3. HDMI IN: Connect a HDMI source with a HDMI M-M cable here 4. Audio OUT: Plug in a local speaker here 5. HDMI OUT: Connect to a HDMI display with a HDMI M-M cable here 6.
Note 1 2 3 4 5 If the HDTV shows video but without audio, please try to set audio mode to stereo. Factory default: Pin#1-OFF[©], Pin#2- OFF[©] for 1080p with stereo. If you encounter any unsolved audio/video output problem during system installation, please turn to Safe Mode (Pin#1-OFF[©] & Pin#2-ON[ª]) to enforce the most compatible 720p stereo output for system check. Bypass means the matrix will maintain playing the original format of HDMI signals in video and perhaps audio.
Hardware Installation HDMI-SPL-2201C Extends HDMI signals to next cascading device with one local display 1. Switch off all devices, including monitors. 2. Connect a local HDMI display to the HDMI out of the HDMI-SPL-2201C and then connect a speaker to the 3.5mm audio socket. 3. Connect to a HDMI source (such as a Blu-Ray Disc player) 4.
HDMI-SPL-2202C Relays HDMI signals to next cascading device with one local display 1. Switch off all devices, including monitors. 2. Connect a local HDMI display to the HDMI Out of the HDMI-SPL-2202C and then connect a speaker to the 3.5mm audio socket. 3. Connect to HDMI-SPL-2202C via RJ-45 in by a CAT5 cable. 4. Connect to next HDMI-SPL-2202C (for cascading), to HDMI-EXT-0101C-RX (to HDTV at long range), or HDMI-EXT-1111C-RX (to HDTV at mid range) via RJ-45 out by a CAT5 cable. 5.
HDMI & RJ-45 Pin Definition Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 SCL Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0– Pin 16 SDA Pin 3 TMDS Data2– Pin 10 TMDS Clock+ Pin 17 DDC/CEC Ground Pin 4 TMDS Data1+ Pin 11 TMDS Clock Shield Pin 18 +5 V Power Pin 5 TMDS Data1 Shield Pin 12 TMDS Clock– Pin 19 Hot Plug Detect Pin 6 TMDS Data1– Pin 13 CEC Pin 7 TMDS Data0+ Pin 14 Reserved (N.C.
Notice 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI or HDMI display EDID information. 2. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C. 3. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI sources, and the type of HDMI display.
~ 11 ~
