Oecoplan 290 GS A++NF User manual Freezer
CONTENTS Safety information Control panel First use Daily use Helpful Hints and Tips 2 4 5 5 6 Care and cleaning 6 What to do if… 7 Technical data 10 Installation 10 Environmental concerns 13 Subject to change without notice In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings.
Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel to avoid hazard. • • • • 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5.
in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked are recyclable.
It is possible to deactivate the function at any time by pressing Action Freeze button. The Action Freeze light will switch off.
Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation. Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. Removal of freezing baskets from the freezer The freezing baskets have a limit stop to prevent their accidental removal or falling out.
Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with lukewarm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris. • rinse and dry thoroughly. Make sure the door is open and then: 1. Loosen the upper edge of the grille by pulling outward/downward. 2. Pull the grille straight out to completely remove it. 3. Vacuum clean under the cabinet.
Important! The operation of the appliance goes with certain sounds (compressor and circulating sound). This not means a trouble, but a normal operation. compressor does not mean being no current. That is why you must not touch the electrical parts of the appliance before breaking the circuit. Important! The appliance operates discontinuously, so the stopping of Problem The appliance is noisy. Possible cause Solution The appliance is not supported properly.
Problem Possible cause Solution The mains plug is not connected to the mains socket correctly. Connect the mains plug to the mains socket correctly. The appliance has no power. There is no voltage in the mains socket. Connect another electrical appliance to the mains socket. Check fuse. Contact a qualified electrician. The lamp is defective. Refer to "Replacing the lamp". The door has been open to long. Close the door. Door interferes with ventilation grill. The appliance is not levelled.
TECHNICAL DATA Dimension Height 1850 mm Width 660 mm Depth 680 mm Rising Time 14 h Voltage 230 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATION Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. In this case, the space behind the top cupboard must be at least 50 mm deep.
This appliance complies with the E.E.C. Directives. Removing the transport support Your appliance is equipped with transport support to secure the door during transportation. To remove them do these steps: 1. Open the door. 2. Remove the transport support from the door sides. 3. Remove the transport support from the lower hinge (some models). Important! Some models are fitted with a silencing pad under the cabinet. Do not remove this pad. Install the spacers on the back side of the panel.
B Door reversibility To change the opening direction of the door, do these steps: 1. Remove the plug from the power socket. 2. Remove the ventilation grille. Remove the filling and install it on the opposite side of the grille. 3. Lay the appliance back side down on a wooden support. 4. Unscrew and move the pin to the other side. A 6. Remove the door closing device on the door (h1). Screw on the door closing device provided within the accessory bag on the opposite side (h2). 1 2 3 5.
Warning! Reposition, level the appliance, wait for at least four hours and then connect it to the power socket. Do a final check to make sure that: • All screws are tightened. • The magnetic seal adheres to the cabinet. • The door opens and closes correctly. Warning! If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket. 10. Put the cabinet in position.
Info Service Postfach 2550, 4002 Basel Info-Tel. 0848 888 444* www.coop.ch *Nationaler Tarif/Tarif national/Tariffa nazionale Servicestelle Wangen Postfach 4612 Wangen bei Olten Fax 062 206 33 12 Service après-vente Ch.
