CG408TT CG412TT Korean Chinese Thermal Transfer Type 203 dpi/305 dpi German English CG4 Series CG408DT CG412DT Direct Thermal Type 203 dpi/305 dpi Quick Guide CG408_412_E_Hyo1_4.
English FCC WARNING You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Safety Precautions This section describes how to use the printer safely. Be sure to read it carefully before using the printer. Pictographic Symbols This instruction manual and the printer labels use a variety of pictographic symbols to facilitate safe and correct use of the printer and to prevent injury to others and property damage. The symbols and meanings for them are given below. Be sure to understand these symbols well before reading the main text.
Caution English Do not place in areas with high humidity Power cord • Keep the power cord away from • Do not place the printer in areas with high humidity or hot devices. Getting the power where condensation forms. If cord close to hot devices could condensation forms, cause the cord’s covering to immediately turn off the power melt and cause a fire or switch and do not use the electrical shock. • When unplugging the power printer until it dries.
Precautions for Installation and Handling Printer operation can be affected by the printer environment. Refer to the following instructions for installation and handling of CG408/412 series. Select a Safe Location Place the printer on a surface that is flat and Keep the printer out of high temperature and level. humidity. Do not place the printer on a location that produces vibration. Avoid locations subject to extreme or rapid changes in temperature or humidity.
Table of Contents Safety Precautions ········································································· I Precautions for Installation and Handling ···································· III English Names of Parts ············································································· 2 Turning On the Power ··································································· 6 Basic Specifications ····································································· 8 CG408_412_E.
Checking Accessories Make sure that you have received all of the following items in the package. If there are any accessories missing, contact your nearest dealer or the store where you purchased the printer. Quick Guide (this manual) English Leaflet (Global warranty) AC power cord AC adapter ▲ About the Box Please retain both the box in which the printer was packed and the cushioning material (cushions that hold the printer in place).
Names of Parts ▲ Printer Unit (Unit Exterior) Operation panel English Top cover Cover open/close latch Label discharge outlet ▲ Back (USB + RS-232C Interface) USB connector RS-232C connector DC input power terminal (Power connector) ▲ Back (USB + LAN Interface) USB connector LAN connector DC input power terminal (Power connector) ▲ Back (USB + IEEE1284) IEEE1284 USB connector DC input power terminal (Power connector) 2 CG408_412_E.
When Top Cover is Opened ▲ For CG408DT/412DT Print head English Paper holder Paper holder slide lever Paper sensor Platen roller ▲ For CG408TT/412TT Print head Ribbon unit Paper holder Paper holder slide lever Paper sensor Platen roller 3 CG408_412_E.
When Top Cover is Opened (Cutter Type (Optional)) Paper holder Paper holder slide lever Paper sensor Platen roller English Cutter unit When Top Cover is Opened (Dispenser Type (Optional)) Paper holder Paper holder slide lever Paper sensor Platen roller Dispenser paper sensor Backing paper discharge outlet (When the dispenser unit is open) Dispenser unit 4 CG408_412_E.
When Top Cover is Opened (Linerless Type (Optional)) Paper holder Paper holder slide lever Paper sensor Platen roller English Linerless paper sensor ▲ Operation Panel POWER button Press this button to turn the power on or off. ON LINE (POWER) lamp The lamp lights green when the printer is online and blinks green when the printer is offline. ERROR lamp The lamp lights or blinks red when an error is detected in the printer.
Turning On the Power Power Setting Plug the DC power cord of the AC adapter into the printer and turn on the power. Connect the AC power cord to the AC adapter. English 1 AC adapter AC power cord 2 Connect the printer AC adapter AC power outlet. When plugging the DC power cord into the printer's power connector, make sure the DC power cord connector is oriented properly. When plugging in the DC power cord to the printer, use one hand to hold the printer while using the other hand to plug in the cord.
3 P re s s t h e P O W E R b u t t o n o n t h e operation panel of the unit. The ON LINE (POWER) lamp lights. Check that the ON LINE (POWER) lamp is lit. POWER button ON LINE (POWER) FEED/LINE Press the POWER button to turn off the printer. When the power is off, the ON LINE (POWER) lamp turns off. English 4 ERROR CAUTION • The power cord set supplied with this printer is only for use with this printer. Do not use it for other electrical products.
Basic Specifications CG408DT Direct Thermal Head density (Resolution) Printing effective area Unprintable area 203 dpi 305 dpi (8-dot/mm) (12-dot/mm) 300 mm pitch x 104 mm wide Label Length direction Upper: 1.5mm Lower: 1.5mm (Not including backing paper) Width direction Left: 1.5mm Right: 1.5mm (Not including backing paper) Linerless label Length direction Upper: 4.0mm Lower: 1.5mm Width direction Left: 1.5mm Right: 1.
CG408DT CG412DT CG408TT CG412TT Maximum ø128 mm Inner diameter of paper roll core: ø40 mm (ø1.5 inches) Length: Maximum 100m Width: 110 mm ± 0.5 mm Outer diameter: Max.ø38 mm (Inner diameter of ribbon core: ø12.7 mm) — Winding direction: Face-out winding Winding method: Ribbon core winding method *Recommended use of carbon ribbon manufactured or specified by SATO.
CG408DT CG412DT CG408TT CG412TT EAN-13 Composite (CC-A/CC-B) EAN-8 Composite (CC-A/CC-B) UPC-A Composite (CC-A/CC-B) UPC-E Composite (CC-A/CC-B) GS1-128 Composite (CC-A/CC-B/CC-C) GS1 DataBar Composite (CC-A/CC-B) GS1 DataBar Truncated Composite (CC-A/CC-B) GS1 DataBar Stacked Composite (CC-A/CC-B) GS1 DataBar Stacked Omni-Directional Composite (CC-A/CC-B) GS1 DataBar Limited Composite (CC-A/CC-B) GS1 DataBar Expanded Composite (CC-A/CC-B) GS1 DataBar Expanded Stacked Composite (CC-A/CC-B) * GS1 DataBar is
CG412TT English Model name CG408DT CG412DT CG408TT Standard functions 1 Status return function 2 Graphic function 3 Sequential number function 4 Form overlay function 5 Custom character registration function 6 Black/white inversion function 7 Ruled line function 8 Format registration function 9 Zero slash switching function 1 Paper end detection Self-diagnostic 2 Cover open detection function 3 Test print 4 Ribbon end detection (for thermal transfer type only) 5 Cutter error (When the cutter unit is insta
CG408_412_E_Hyo2_3.
*Q 02444000* CG408_412_E_Hyo1_4.
