User manual

GSM LT-1 SATEL 15
10.2.3 Function list
[0][1][
*
][
*
][?][?][?][?][#] – SIM card PIN code (4 digits). The code saved in module memory
does not change the code stored on the SIM card. The [0][1][
*
][
*
][#] sequence deletes the
PIN code from module memory.
[0][2][
*
][
*
][?...][#] – SMS center number – the telephone number necessary for sending text
messages. The number of its digits must be within the range of 1...16. The entered
number depends on the GSM network, where the telephone is activated. It must be
preceded by the country code suitable for the operated network.
The [0][2][
*
][
*
][#] sequence deletes the previously saved SMS center number.
[0][3][
*
][
*
][?][?][?][?][?][?][#] – SMS password (6 characters) required for a remote
change of the modem format. Sending to the module of an SMS containing the
[?][?][?][?][?][?]=NN sequence will change the modem operating format available in the
GSM telephone. The two NN digits define the format as described in the function 08. Using
DTMF signals it is possible to program a password comprised of digits only (0...9), while
using the DLOAD10
program you can program a password comprised of both letters and
digits. The [0][3][
*
][
*
][#] sequence deletes the previously programmed password.
[0][4][
*
][
*
][?][?][?][?][?][?][#] – SMS password (6 characters) which calls the SERV
modem command. The function applies to interaction between the module and the
CA-64/INTEGRA alarm control panel. Sending to the module of an SMS containing the
programmed password makes the control panel call back to the number saved in its
memory as the "Dload64 telephone"/”DLOADX telephone” in order to start the
downloading function. If the control panel is to call back to another number, the number
should be put into the SMS content as follows: [?][?][?][?][?][?]=dddd. (password, equality
sign, telephone number, point). If the module receives an SMS message initiating
connection with the INTEGRA control panel and the access from DLOADX program is
blocked, the module will send a SMS message stating that "Remote access from DloadX
program is not granted" to the number preprogrammed with function 26. Using DTMF
signals it is possible to program a password comprised of digits only (0...9), while using the
DLOAD10 program you can program a password comprised of both letters and digits. The
[0][4][
*
][
*
][#] sequence deletes the previously programmed password.
[0][5][
*
][
*
][?][?][?][?][?][?][#] – SMS password (6 characters) which calls the USER
modem command. The function applies to interaction between the module and the
CA-64/INTEGRA alarm control panel. Sending to the module of an SMS containing the
programmed password makes the control panel call back to the number saved in its
memory as the "GuardX telephone”/”Guard64 telephone” in order to start the remote
communication with the GUARD64/GUARDX program. If the control panel is to call back
to another number, the number should be put into the SMS content as follows:
[?][?][?][?][?][?]=gggg. (password, equality sign, telephone number, point). Using DTMF
signals it is possible to program a password comprised of digits only (0...9), while using the
DLOAD10
program you can program a password comprised of both letters and digits.
The [0][5][
*
][
*
][#] sequence deletes the previously programmed password.
[0][6][
*
][
*
][?][?][?][?][#] – PAGER station number is 4 digits or a sequence of 1 to 4 digits
(depending on the module firmware version). If the module detects these digits at the
beginning of the dialed number, it will handle the further part of the number as the number
of cellular phone to which it is necessary to send the SMS. The SMS contents should be
transmitted by the alarm control panel in the "pager" system form. The [0][6][
*
][
*
][#]
sequence will delete the number.
[0][7][
*
][
*
][?][?][?][?][#] – CA-64 station number (4 digits). This function is not used.
It applies to interaction with the CA-64 control panel. The [0][7][
*
][
*
][#] sequence will delete
the number.