Communication module GSM LT-1 Firmware version 1.14 gsmLT-1_en 04/13 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.
WARNINGS For safety reasons, the module should only be installed by qualified personnel. Prior to installation, please read carefully this manual in order to avoid mistakes that can lead to malfunction or even damage to the equipment. The module can only work in conjunction with PSTN subscriber lines. Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty.
SATEL GSM LT-1 1 CONTENTS 1. 2. GSM LT-1 MODULE FEATURES .......................................................................................................... 2 TYPICAL MODULE APPLICATIONS ........................................................................................................ 2 2.1 INTEGRATION WITH INTEGRA CONTROL PANELS ......................................................................... 3 2.2 WORKING IN CONJUNCTION WITH STAM-1 / STAM-2 MONITORING STATION ....................
2 GSM LT-1 SATEL 1. GSM LT-1 MODULE FEATURES Simulation of analog telephone line when using the GSM connection. Built-in industrial GSM telephone working in 850/900/1800/1900 MHz cellular telephony networks. Capability of remotely checking the status of available resources and the account validity of SIM card installed in the module. An output to signal the telephone line trouble and/or problem with logging into GSM network. Module control by means of SMS messages.
SATEL 2.1 GSM LT-1 3 INTEGRATION WITH INTEGRA CONTROL PANELS Fig. 1. Module working in conjunction with the INTEGRA control panel.
4 2.3 GSM LT-1 SATEL WORKING IN CONJUNCTION WITH PBX STATIONS The module can work in conjunction with the Private Branch Exchanges (PBX) as an additional external telephone line. It can be used to make outgoing calls to the mobile phone numbers and thus optimize the costs incurred. 3. 3.1 DESCRIPTION OF THE MODULE DESCRIPTION OF THE ELECTRONICS BOARD Fig. 3. View of GSM LT-1 module electronics board. Explanations for Fig. 3: 1 - external antenna connection. 2 - GSM industrial telephone.
SATEL GSM LT-1 5 must be activated in the SIM card installed in the module, if the module is to use the functions requiring the GPRS technology. 4 - LEDs (see: section „LED indicators”): STAT LED indicate the module status, SIG LED indicate the level of antenna signal received by GSM telephone, TX and RX LEDs indicate that data are being transferred through the RS-232 port. 5 - RS-232 port.
6 GSM LT-1 SATEL – PUK2 code required, – SIM card busy, – module restart on switching power on, – SIM card damaged, – invalid SIM card, – other errors, – active connection. SIG indicates level of signal received by GSM telephone: – no GSM network signal, – level of signal 1, – level of signal 2, – level of signal 3, – level of signal 4. 4. INSTALLATION Disconnect power before making any electrical connections. It is not advisable to power up the device if the antenna is not connected.
SATEL GSM LT-1 7 9. If the module is to be used as the external modem, connect the module RS-232 port to the suitable port of the device. 1 2 3 4 5 6 Fig. 4. Installing the SIM card. 5. PROGRAMMING You can configure the module using the keypad of telephone connected to the R-1 and T-1 terminals, or a computer with suitable software installed (locally and remotely). 5.1 DTMF PROGRAMMING 5.1.1 Programming mode In order to enter the module programming mode: 1.
8 GSM LT-1 SATEL the required parameters. To enter digits, use the number keys. You can also enter special characters: # - press in turn the [*] and [1] keys; * - press twice the [*] key; + - press in turn the [*] and [0] key. Having entered the data, confirm them using the [#] key. When programming, the following sounds can be heard in the telephone handset: 3 short beeps – correct data; 2 long beeps – incorrect data.
SATEL GSM LT-1 9 [12**] – a six-digit access code, necessary to program the module using a telephone set. In the module with factory default settings, the 123456 value is programmed. The code can only be checked in the DLOAD10 program (see: "Access code" p. 18). [13**] – enter the digits 1234 and confirm using the [#] key to restore the factory settings (see: „Module factory settings ” p. 34).
10 GSM LT-1 SATEL 2 – 5 h 57 min, 3 – 11 h 56 min, 4 – 23 h 55 min, 5 – 2 d 23 h 53 min, 6 – 6 d 23 h 30 min. Having entered the parameter, you can either confirm it at once with the [#] key or enter the next parameter to define whether the first test transmission is to be performed at a time randomly selected by the module: 0 – no, 1 – yes. [20**] – parameter defining whether the module test transmission is to have a priority (see: "Messaging priority" p. 21): 0 – no, 1 – yes.
SATEL GSM LT-1 11 [41**] – a sequence of up to 4 digits which will replace the "+" character in the phone number from which the CLIP connection is established to the module. [97**] – parameter defining whether the module is to execute the reporting function: 0 – no, 1 – yes. [98**] – parameter defining whether the module is to monitor the status of connection with INTEGRA control panel through the RS-232 port: 0 – no, 1 – yes. The connection will be monitored for the INTEGRA control panel version 1.
12 GSM LT-1 SATEL 3. character – 3. phone number for test transmission (0 – no; 1 – yes); 4. character – 4. phone number for test transmission (0 – no; 1 – yes); 5. character – phone number for SMS control confirmation (0 – no; 1 – yes). [117**] – 6 digits representing the SMS control command to be sent to the module to transfer the network codes – USSD (see: "USSD codes forwarding message" p. 22).
SATEL GSM LT-1 13 Fig. 5. Computer connection to the module RS-232 port. Shown on the left is the PIN-5 plug to be connected into the module connector. Shown on the right is DB-9 female plug (solder side view). A ready cable is offered in the DB9F/RJ-KPL set. Fig. 6. Selecting the GSM module after starting the DLOAD10 program.
14 GSM LT-1 SATEL Fig. 7. "Configuration" window. 5.2.2 Remote programming During remote programming, the module will not execute any other functions requiring the use of GSM telephone. Most of the parameters required for remote programming of the module can only be programmed using the DLOAD10 program.
SATEL GSM LT-1 15 In order to establish communication between the module and the computer do the following: 1. Start the DLOAD10 program. 2. Select the "TCP/IP" in the "Communication" menu. A window will open in which information on server activation will be displayed (see: Fig. 8). Fig. 8. "TCP/IP" window. 3. Send to the GSM module telephone number an SMS message containing the control command used to start communication with the DLOAD10 program.
16 GSM LT-1 SATEL Explanations for Fig. 9: 1 - GSM module type. 2 - module firmware version (version number and build date). 3 - information on the status of communication between module and program. 4 - time and date according to the module clock. When logging into the network, the module updates these data automatically, if the operator whose services are used by the module offers such a function. 5 - information on the GSM telephone status. 6 - level of signal received by the GSM antenna.
SATEL GSM LT-1 17 Fig. 11. Functions related to the DLOAD10 program access. 2. Enter the old access code and click on the "OK" button 3. Enter the new access code and click on the "OK" button. 4. Enter again the new access code and click on the "OK" button. The program allows to get access based on additional codes which can be programmed and for which authority level can be defined (in the "File" menu, select "Configuration", and then "Dload10 users" – see: Fig. 11). 5.2.
18 GSM LT-1 SATEL PIN code [01] – PIN code of SIM card. Entering a wrong code may result in blocking the SIM card. SMS center no. [02] – telephone number of the short message service center (up to 16 characters). If the number has been written by the operator to the memory of SIM card installed in the device, it need not be entered. In such a situation, the module will download it automatically. Otherwise, it is necessary to enter the number, if the module is to send SMS messages.
SATEL GSM LT-1 19 DNS server – IP address of DNS server to be used by the module. It is necessary for GPRS communication, when the address of device to which the control panel is to connect (monitoring station, computer with DLOAD10 program) has been entered in the form of a name. If all addresses are entered in the form of an IP address (4 decimal numbers, separated by dots), the DNS server address need not be programmed. User – user name for Internet GPRS connection.
20 GSM LT-1 SATEL and the DLOAD64 program (this applies to the CA-64 control panel firmware version 1.04.03 or newer, and the DLOAD64 program version 1.04.04 or newer). The SMS message sent to the module may have the following form: xxxxxx=yyyy. or xxxxxx=yyyy=, where "xxxxxx" is the control command and "yyyy" is the computer telephone number with which the control panel is to establish communication. If no telephone number is given, the control panel will connect to the number programmed in its memory.
SATEL GSM LT-1 21 the number to which the SMS message is sent, if the module fails to send the event code to the monitoring station (see: "Tel. number" p. 25). No voltage on T-1/R-1 if GSM trouble [17] – if this option is enabled, voltage on the telephone line terminals will be turned off in case of the GSM telephone trouble. Generate routing signal [18] – if the option is enabled, the connection setup is audibly signaled.
22 GSM LT-1 SATEL Autorestart every [113] – you can program the time period after which the module, if not used, will restart the telephone. From 1 to 25 hours can be entered. The "use" of the module shall be understood as: receiving the module outgoing call, occurrence of the incoming call signal, receiving acknowledgement of an SMS message sent by the module, receiving an SMS message, sending data by the module working as an external modem.
SATEL GSM LT-1 23 Events buffering – the option is available in the module with built-in GSM u-blox LEON-G100 telephone. It refers to the events received from the INTEGRA control panel through the RS-232 port and the test transmissions sent by the module to the monitoring stations. If the option is enabled: each event received from the control panel is acknowledged at once, events are recorded in the event log (see: section "Events buffer" tab p. 28).
24 GSM LT-1 SATEL Reporting test send all media – if this option is enabled, the module test transmission is sent over all links which have been programmed using the "Priority" function. If the "Events buffering" option is enabled and the test transmission is sent over all links, the "Events buffer" tab will only display the event communicating information about test transmission sent over the reporting link programmed as the last one.
SATEL GSM LT-1 25 starting from the first reporting link on the list, only after 7.5 minutes have elapsed since sending the last event. Telephone numbers CDS reporting – the telephone number to which events are reported using the CSD technology. It must be preceded by the country code. The CSD data transmission service is usually available in the basic package of services offered by the mobile network operator, however before programming suitable parameters you must make sure if it is possible to use it.
26 5.2.8 GSM LT-1 SATEL "TCP/IP downloading" tab Fig. 14. "TCP/IP downloading" tab. Most of the parameters required for correct communication between the module and the DLOAD10, DLOADX and GUARDX programs using the GPRS technology can only be programmed by means of the DLOAD10 program. Communication over TCP/IP Server address – address of the computer from which the module can be remotely programmed. It can be entered as an IP address or as a name.
SATEL GSM LT-1 27 DloadX key – the string of 12 alphanumeric characters (digits, letters and special characters) defining the key with which the data sent to the DLOADX program will be encrypted. The module will only establish connection to the program using the correct key. encrypted transmission – if this option is enabled, the data transmission between module and program will be encrypted. The option must be enabled.
28 GSM LT-1 SATEL Server from SMS – if this option is enabled, the address of server, to which the module is to connect, and the port number can be entered in the content of SMS message initiating the connection. If the address is not entered, the module will connect to the server whose address has been programmed in the module.
SATEL GSM LT-1 29 The events are presented in the descending order (the newest at top, the oldest at bottom). The individual columns show the following information: Received – the date when event was received by the module. Send – the date when event was sent by the module to the monitoring station. S1 / S2 – reporting status (S1 – monitoring station 1, S2 – monitoring station 2): --- – the event is not reported, .
30 GSM LT-1 SATEL The module offers the following forms of event code sending to the monitoring station: GPRS – packet data transmission. CSD – data transmission. SMS – SMS messages. If the event code is sent using an SMS message, the module will not receive the acknowledgement of receipt of the event code by the monitoring station. Therefore, this reporting link should be used as the last one (see: "Priority" p. 24).
SATEL 7.2 GSM LT-1 31 STARTING THE CSD REPORTING Select CSD as the reporting link (see: "Priority" p. 24). Program the telephone number for CSD reporting (see: p. 25). 7.3 STARTING THE SMS REPORTING Select SMS as the reporting link (see: "Priority" p. 24). Configure the parameters of monitoring station(s) (see: p. 24): enter the telephone number for SMS reporting; program the SMS message format in which event codes will be sent to the monitoring station. 7.
32 GSM LT-1 SATEL the call is answered. If the mobile phone of the message addressee is turned off or out of the network range, and the voice mail service is not active, an automatic message about the existing situation can be generated in the telephone receiver and no number busy signal is sent back. In such a case the test transmission will be considered by the module as received, but the user will loose information on the test transmission being sent.
SATEL GSM LT-1 33 pressing in turn the numeric key and [*] means entering the letter on the left-hand side of the given key; pressing in turn the numeric key and [#] means entering the letter on the right-hand side of the given key; pressing the [0] key means entering a space; pressing in turn the [0] and [*] keys means entering a dash; pressing the [1] key means entering a dot, pressing in turn the [0] and [#] keys means switching over to the numeric mode.
34 GSM LT-1 SATEL If the "Server from SMS" ("Firmware update" tab) option is enabled in the module, you can send a message with the xxxxxx=yyyy:zz. or xxxxxx=yyyy:zz= content, where "xxxxxx" is the control command used to start the update, "yyyy" is the address of server with the latest firmware for the module (IP address or name), and "zz" is the server port number. The module will connect to the computer whose address is given in the SMS message.
SATEL GSM LT-1 35 No voltage on T-1/R-1 if GSM trouble Generate routing signal Convert "+" to digits: 00 CLIP answering: no Number of retries: 3 Messaging trouble SMS: CLIP failed Autorestart every: 24 h "Reporting" tab: Enabled options: Events buffering Number of reporting retries before sending other way: 3 Send SMS: Monitoring trouble (MS #) Code programmed for the event: Periodical reporting test "TCP/IP downloading" tab: Enabled options: Server from SMS Encrypted transsmision "Firmware update" tab:
36 GSM LT-1 SATEL IMPORTANT: PIN No.................................. PUK No................................................................... Telephone No. ...................................................................................................... ............................................................................................................................... ........................................................................................................................
