ASD-250 Wireless smoke detector Firmware version 1.00 asd-250_en 03/21 SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND tel. +48 58 320 94 00 www.satel.
IMPORTANT Prior to installation, please read carefully this manual in order to avoid mistakes that can lead to malfunction or even damage to the equipment. Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty. The rating plate of the device is located inside the enclosure. SATEL aims to continually improve the quality of its products, which may result in changes in their technical specifications and software.
The ASD-250 detector can detect the early stages of fire development when there is some visible smoke. It can operate as a stand-alone device or within the ABAX 2 / ABAX two-way wireless system. This manual applies to the detector with firmware version 1.00, which is supported by: ABAX 2: – ACU-220 / ACU-280 controller, – ARU-200 repeater. ABAX: – ACU-120 / ACU-270 controller (firmware version 5.04 or newer), – ARU-100 repeater (firmware version 2.
2 ASD-250 SATEL Operating modes You can set the operating mode using the jumper located on the printed circuit board (Fig. 2): jumper removed – stand-alone mode. jumper installed – working in ABAX 2 / ABAX system. The detector is operating similarly as in the stand-alone mode, but it additionally: – communicates with the ABAX 2 / ABAX controller / INTEGRA 128-WRL control panel, – supervises the tamper switch state.
SATEL ASD-250 3 / ABAX system, the low battery info is sent during each transmission to the controller / control panel. Working in ABAX 2 / ABAX system Radio communication The detector connects to the controller / control panel at regular time intervals to provide information about its state (periodical communication).
4 ASD-250 SATEL Legend for Figures 3 and 4: living room. room. hall, lobby, etc. kitchen. basement. basic location for detector installation. additional location for detector installation. 4. Installation The detector enclosure can not be closed without the battery inserted. Do not install the battery if the sounder is disconnected. There is a danger of battery explosion when using a different battery than recommended by the manufacturer, or handling the battery improperly.
SATEL ASD-250 5 2. Turn the cover counter-clockwise (Fig. 7) and remove it (Fig. 8). 3. If the detector is to work as a stand-alone device, remove the jumper (Fig. 2) and skip the steps 5-9. After the battery is installed, removing / placing the jumper will have no effect on the detector operation. 4. Install the battery. 5. Add the detector to the wireless system (see the ABAX 2 / ABAX controller manual or the INTEGRA 128-WRL control panel installer manual).
6 ASD-250 SATEL 2. Remove the screw fastening the cover (Fig. 6). 3. Turn the cover counter-clockwise (Fig. 7) and remove it (Fig. 8). 4. Remove the battery. 5. Disconnect the plug connecting the sounder wires with the electronics board (Fig. 9). 6. Push outward the catches (Fig. 10) and take out the electronics module with the optical chamber (Fig. 11). 7. Push outward the catch securing the optical chamber cover (Fig. 12) and remove it (Fig. 13). 8.
SATEL ASD-250 7 9. Replace the cover of the optical chamber. 10. Lay the sounder wires in their corresponding grooves. 11. Secure the electronics module with the optical chamber in the cover mounting catches. The board must be mounted so that the LED coincides with the light guide. 12. Reconnect the plug connecting the sounder wires with the electronics board. 13. Re-install the battery. 14. Replace the detector cover and lock it with the screw. 15. Press the test / reset button (Fig. 1).
8 ASD-250 SATEL The ASD-250 wireless smoke detector conforms to the essential requirements of the EU Regulations and Directives: CPR 305/2011 Regulation of the European Parliament and of the Council of 9 March 2011 laying down harmonized conditions for the marketing of construction products and repealing the Council Directive 89/106/EEC on construction products; RED Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonization of the laws of the Member States re
