Instructions / Assembly
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should a
xture be hung on house electrical wires, nor should a swag type
xture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how to
proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts
are included as shown in gure. Be careful not to misplace any of
the screws or parts, which are needed to install this xture.
INSTALLATION
STEP 1: Place lock washer (D) over end of nipples (F) protruding
through crossbar (C) and thread hex nut (E) onto nipples (F) until
tight. Take the crossbar assembly and mount to ceiling outlet box
using screws (B). Tighten screws securely with screwdriver.
STEP 2: Adjust the chain to your desired length by removing links
if needed.
STEP 3: Pull the supply wires through the chain alternating links.
After the wires are through the chain, pull the supply wires and the
ground wire through the canopy lock ring (K) and the ceiling canopy
(J) in order.
STEP 4: Attach one end of the chain to the xture loop (L) with one
quick link (H). Lift the xture and chain up and attach the other end
of the chain onto the canopy chain loop (G) with another quick link
(H). The xture will now hang safely.
STEP 5: Feed the supply wires and ground wire through the canopy
chain loop (G) and nipple (F) into the outlet box.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from the
xture (if supplied) around the green grounding screw, then connect
it to ground wire from the outlet box (if not xed on the outlet box)
using a wire connector (not supplied). If ground wire from the xture
is not supplied, wrap the ground wire (if not xed on the outlet box)
from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify
which group your xture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape
or smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check
again for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: Raise the ceiling canopy (J) and canopy lock ring (K) up
chain and over the canopy chain loop (G). Tighten the canopy lock
ring (K) onto the canopy chain loop (G) until tight.
STEP 2: Install Bulb, E26 medium base (not included). Do not
exceed maximum wattage rating.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-5944
ARTÍCULO Nº: 60-5944
ARTICLE N°: 60-5944
FIGURE
© Copyright 2022 Satco Products, Inc. 8/22 v1.0