START HERE In-Wall Wi-Fi Dimmer S11268 Installation Guide WIFI 2.
This dimmer is rated for use with Incandescent and dimmable LED bulbs and fixtures 120VAC 60HZ 450W INC, 150W LED NOTE: A NEUTRAL WIRE IS REQUIRED FOR INSTALLATION Derating is required when installing in multi-gang applications:
WARNING: This product may represent a possible shock or fire hazard if improperly installed or attached in any way. Product should be installed in accordance with the owner’s manual, current electrical codes and/or the current National Electric Code (NEC). CAUTION: RISK OF ELECTRIC SHOCK. - TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING. CAUTION: RISK OF FIRE. - FOR CONTROL OF INCANDESCENT OR LED LUMINAIRES ONLY.
OPERATION 1) Power Indicator & Configuration Light 2) Air Gap Switch (Cuts power to light) 3) Dim/Bright Bar – Raise Lights 4) Dim/Bright Bar – Lower Lights 5) Light Level Indicator Bar 6) On/Off Switch
PARTS INCLUDED Wall plate (x1) Mounting frame (x1) Smart dimmer (x1) Inner frame screws (x2) Mounting screws (pre-installed) (x2)
Verify that a neutral wire is available prior to installation How do I know if I have a neutral wire? 1. Turn power off at your breaker box and ensure the power is off 2. Remove the wall plate and existing device from the wall box 3. Remove and straighten all wires from the device 4. If you see a white wire (or bundle of them), it is likely that you have a neutral in that switch box 5.
DIMMER INSTALLATION Turn power OFF at the circuit breaker and ensure power is off. WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse and test that power is off before wiring.
Identify if your wiring is SINGLE POLE or 3-WAY SINGLE POLE: control from a single location 3-WAY: control from 2 locations
You will need to determine which is the “LINE” wire and wall box and which is the “LOAD” wire and wall box. Your old switch may have a screw terminal of a different color (usually black). This will either be the “LINE” connection or the “LOAD” connection. Tag this wire with a piece of electrical tape. Disconnect all wires from the old switch and ensure no wires are touching. Turn the power back on at the circuit breaker. Use a handheld voltage tester to determine if the tagged wire is “live”.
NOTE: Ensure power is off before preforming this step! Preparing and connecting wires: Use with #12-14 AWG solid copper or copper-clad wire. Strip wires to 2 cm (.8 inch). Insert wires into terminal holes and secure connections by tightening terminal screws to 16 lbf-in (1.8 N.M) as shown.
SINGLE POLE WIRING Ensure that the following connections are made: “LINE” wire to the terminal marked AC-L “LOAD” wire to the terminal marked LOAD Neutral wire to the terminal marked AC-N Ground wire to the terminal marked GND
3-WAY WIRING Note: A single pole or 3-way switch can be used alongside the smart dimmer. IMPORTANT: The switch must be installed in the “LINE” wall box and the smart dimmer must be installed in the “LOAD” wall box.
MOUNTING Push wires into the wall box and push dimmer into opening Mount the dimmer into wall box and install the wall plate TESTING Turn power back on at the circuit breaker Test the device to ensure that the lights will turn on and off
DOWNLOAD THE FREE “STARFISH SMART LIGHTING” APP Please refer to our Starfish user guide for detailed instructions on how to pair your device TROUBLESHOOTING Lights are flickering: -Lamp has a bad connection. - The dimmer wire connections are not firmly secured. - If using in a dimmable LED or CFL application you can use the APP in the setting to adjust the minimum brightness until you do not see flicking. Light does not turn ON: - Circuit breaker or fuse has tripped. - Bulb or lamp is burned out.
ENJOY THESE OTHER GREAT STARFISH WIFI SMART LED PRODUCTS ͭ͵ Technical Support www.satco.
:,. ·• • 00 •✓ •.o.-oooo•• • ••oooo • •. ,. ··•00 • o••· 0 •.• 0 0 •• • : •• 0 0 • STARFISH™ live Ufe eritightened 0 DOWNLOAD THE STARFISH APP I • ~ . App Store ► Google Play System Requirements Minimum iOS 9.3 or Android 4.4 • Dedicated 2.4GHz Wifi Network • TECHNICAL SUPPORT www.satco.
a II Launch the App and tap uReglster" for new accounts or "Login" for existing accounts. Enter E-Mail address, then tap MGet verification code" .., _.,. < II ...... Create a Password then tap "Done" < SetPelaword ...... .,,t M•.ai-•- 19'-1..
Create/Share a Home Create a Home a Tap the "Me" button on the bottom of the screen, and then tap "Home Management". Tap the "Create a home" button to setup your home. Q ........._ ea .. - Q --· ..... IATCD ~ - u , t_ , --_, . l C S,.,\, I . J ....
Share a Home II From the Home Management screen, select the Home that you would like to share. Tap "Add Member" and select the way that you would like to send the Invitation • • • 1WVMUI ( D HorttieMa,og :ad Enter the user information and select if the new member will be an ''Adn1inistrator" or a "Common Member" in the Home.
Add Devices II Tap the plus(+) button on the upper right hand comer to add a device -- AIDI El Make sure you are connected to a 2.4GHz WIFi Network then manually add smart llghtlng devices ,_. < • .....,.., . '• -.... -....
11:J Frt your bulb In to the desired fitting & switch on. Your bulb should be flashing. Note; If the devices are not flashing, tum devices On and Off 5 times to enter pairing mode Reset the deva first. II\ ,,,..,. .. •"'0- _.lht ~"°wan 4111,n(),).
m The status menu will appear. Wait until it's completed. Note: If unsuccessfuJ. please refer to the FAQs on Satco.com/Starfish r-WI-FIII ... . -,dd -♦ .. --• IEJ To rename the device, tap the "Pen" icon, enter the new name and tap "Completed". The device Is now ready to be controlled with the starfish App. ns; t -•l,W----- 'b "\)
Individual Bulb On/Off IIJ Tap the Power Button to turn ttle device On or Off MO f U....~ . .. .
Dimming Slide the dimming bar left or right to set the brightness level Note: Screen shown for "dimming only" product.
Tunable White m Use the round slider to adjust color temperatures from Warm to Cool Slide the dimming bar left or right to set the brightness level
Color Changing Im Tap on any part of the color wheel to select your desired color Use the slide bars to adjust the brightness and color saturation
Effects 11D Tap on a preset effect or create a custom effect by tapping on the edit button
Schedule fJD Tap on 1he "Schedule" button fD Select a time for the event to occur Tap "Repeat" to repeat on certain days of the week, otherwise the event will only occur once. Select the days that you would llke the schedule to repeal Select if you would llke the device to tum on or off. ...... < MISCt t+e 8 14 ···--· ..... PM ~ m TiRler At device control panel, tap the Timer Button to create a countdown timer. Select time and confirm to start the-timer.
Advanced Settings fJJ Additional settings are available 1n the device settings menu. Tap the pen Icon in the upper right corner to access the menu screen / < S~9.5WSl-1bulb3 __ ...,."'° __ _ ..,.c- 0 .... - • ·· ... * ....
Create Groups fl Tap the "Create Group" option NOTE: To create groups you will need at least 2 devices fl Select the devices you want to group and then tap MConfirm" 0lnl CIIICM - flD uw-.
Edit Groups ED fJD Tap the pen Icon In the upper right comer / Rename the group or remove a device from the group. Once complete, tap "Confirm" in the upper right corner. ( 11W.
Automation and Scenes f!J Tap the Smart button on the bottom of the screen and then the plus (+) button on the top right hand comer to setup your first Scene or Automation IAlCO"' .....
EIJ Select "Run Scene" to create a scene that can be executed with the click of a button Select "When weather changes", "Schedule" or "When device status changes" to have your devices run automatlcally based on the condition. °''' < 11, ..... ,;o; t - . ----.. ,~ • Id ""'• • 'MW\-WcN: tltl ~ •
m Select the devices or groups that you would like to be controlled, and then select it you would like those devices to Tum On or Off, and the color. < iUOot ·-- - 11 U U#..,..
m Tap "Next" and then review the Automation or Scene. CIiek ''Save" to activate your Automatron or Scene. - ....,,._ I I _ !I 0 -o~--r e• J ~ ............... ..,.1111,.-ss.it:.tt • ... ....
CONNECTING TO ALEXA Note: Make sure that your Alexa App Is connected to your Amazon device and is working property a Log In to your Alexa App and tap the top left corner to access the menu.
fJ Tap"Skills & Games"
Type "Satco Starfish" and tap on the Icon in the search results. Search Yta>twtfbh 25 Results 0 Starf1'h+do •cfcre 11M ~ ol'e co "'9JoWa oW-.,, HA)( & Aut.,,.. 15 ~llh,_.. •Alna laUJWt suuflslt _ .
a Tap "Enable to Use" to begin linking your account. ., -=- < ~ '..,t.T1 rJ ,..,Tt,.l;, 1',~4 - ,_!] Satco Starfish AW>imt lhwno ~ If you Me a,,y problem wheoyoi, &M ltliS iklll, you can c ~ us with •• st- fllll •Mtc.o.com .a• : SM"" SC.-flih pmdt!CU '-If> YCK1 contlOC honw apptl/llilte You an simply~ &101 to wm on. cum ..
El Enter your Satco Starfish username and password to link your accounts, then tap "Link Now". Note: You must use the same usemame and password from the Starfish App. --... J. - .. I ' / I Done ., . i . . . . . kltti+· tuya'5.com .
II fl Tap "Authorize" on the next page to link your Star1ish account to Alexa Once your Starfish account 1s successfully linked to Alexa, tap "Done" on the top left comer i skills-store.amazon.com C ~ zon alexa ..___.::, . ..... ·... .•... • • • I Satco Starfish has been successfully linked. What 10 do next lose. th.~ .. KIO\'' to dl1tover smart-liome dc111ces you can control w11J1 Al~
II Tap "Discover Devices" to connect your Smart devices . .. " Discover Devices Smart Home devlc.es must be dlsa,ve,-ed befon they c~ be used with Al6i.
El Wait for Alexa to detect the devices from the Starfish App Your devices will now be paired and can be controlled through the Alexa App or through your Alexa device
CONNECTING TO GOOGLE HOME Note: Make sure your Google Home App is connected to your Google device and Is working properly a Open the Google Home App, then tap "Set up device". .. ,.,.,..... U'E X Add and manage 0 s. 14) de.ice ~ +.:, Add home IIClit.e.
fJ Tap "Have something already set up?" • --lTt < ••• Setup S..uprwwdl'fces«adlfedtl "d~-,ld se w sto~ hau• SecuplWWdl"vKIS a ~ (; C l l t - s-n., ~ ...o I iecl ,..__,."" ~ .. _ ~ ,e l0l'llll1hlrlD.. ~ • ,-.:.d ut . rJy Nt up? ..,..
El Type "Satco Starfish" and tap on the icon ,n the search results. ···-- Tl:11 AM X Satco Startistf ·" Q. Starfish's w e r q a - ◊ 123 • t • u y I .
D Enter your Satco Starfish usemame and password to link your accounts, then tap "Link Now". Note: You must use the same username and password from the Starfish App . .e \lt iUW ltt 0oM ., l-02 N.t • i pocy1.tuy.us.eom · · -- • - AA C .
Now that you have linked your Starfish devices to Amazon or Google, you will be able to control them with voice commands from your Alexa or Google Assistant devices. Below are some common voice commands that can be used after you say "Alexa" or "OK.
CONNECTING TO SMART THINGS Note: Make sure your SmartThings App Is connected to your hub and Is working properly a Open the SmartThings App, then tap the top left comer to access the menu Tap "Devices" and then ''Add new device" eo Home .., ,n ... W C S ·M~ &I • Sc ... .
a Select "Satco Starfish" from the "By brand" list, then select the location where you would like to add the device ... - - . i n < Q. Bytorand •• S1 ••11•1 ICM'OOrl i ·=. • - 0S I- ~ sos ~~' < °4(\~ ~ Sr Srwsg'sd !iM Semi 431 N X SelOOI a loeftftOO and room fOf your SatcoStMi&h
El Enter your Satco Starfish username and password to link your accounts, then tap "Link Now" Note: You must use the same usemame and password from the Starfish App .,._Lil Done . .. ... . ~ UIIIM Translation Avnab1e ., ..
a Tap "Authorize" on the next page to link your Starfish account to SmartThings Once your Starfish account is successfully linked to SmartThlngs, tap "Done" on the top left comer Do~ i c2c-us.smartthings..co ··•·· ~-··· .....-.. • .• . . Connection between SmartThings and Satco Starfish is successful. Close this page to finish setup.
ENJOY THESE OTHER GREAT STARFISH WIFI SMART LED PRODUCTS i: •0 0 ·• ~ e ~ • ooo • Oo 0 . 0 . .. 0 •• o oo " 00 .... ••o. o•• ••.. A19 Lamps . " 0 0 • 0 0 • • . • 0 0 Flood and . PAR Lamps 0 II STAR FISH™ • - 1~11;;. - ~ -- live life enlightened =--a . .-. .. - . ...,~ l ~ ., ~'gr~~ I-UP-.~ • - 11 4 11 >,' T - .~ • . ~ IS~ - • \ ~~~ ~ Strip Lights - Recessed Fixtures Smart Lighting Controls .
STARFISH ™ Wi-Fi Dimmer Wall Switch GENERAL SPECIFICATIONS ITEM NUMBER: S11268 Yes-Dimmable Dry Location COMPLIANCE SAFETY LISTING: TECHNICAL SPECIFICATIONS DIMENSIONS LENGTH (in) WIDTH (in) HEIGHT 1.71 2.76 4.53 PACKAGING EACH QTY EACH UPC EACH DIMENSIONS INNER QTY INNER UPC INNER DIMENSIONS CASE QTY CASE UPC CASE DIMENSIONS 1 045923112683 2.95 x 2.17 x 5.12 0 0.00 x 0.00 x 0.00 12 10045923112680 13.78 x 6.30 x 5.
