Instruction manual

50 April 2012 ARRL – the national association for Amateur Radio www.arrl.org
When mounting the high-wattage resistors
onto the PC board the instructions called for
using masking tape to hold the resistors in
place before turning the PC board over and
soldering the parts. I feel that this step is
unnecessary if you take the time to slightly
bend the component leads away from the
hole and then solder the connections. It’s a
minor point, but one that speeds the build.
Testing and Use
Initial testing was a breeze. The instructions
outline a valid testing procedure, which I
followed. However, I
decided to do some
additional testing. Having
a calibrated QRP watt-
meter and dummy load, I
connected the SADL kit
between my Elecraft K3
and my calibrated watt-
meter/dummy load and
proceeded to apply 5 W of RF. With all the
attenuators bypassed I observed 5 W on the
wattmeter. I then switched in the attenuator’s
dummy load and the output meter dropped to
2.5 W. Essentially, both the dummy load in
the attenuator and the dummy load on the
wattmeter are in parallel and the output
should drop to half the initial output of 5 W,
which is exactly what happened.
After switching out the attenuator’s dummy
load I systematically proceeded to crank in
3, then 6, then 9 and finally 12 dB pads and
watched the RF on the calibrated meter. All
worked as advertised with the RF output
dropping from 5 W to 2.5, to 1.25 W, to
0.625 W and so on — just as it should.
One nice thing is the visual indicator.
It’s an LED that lights when the inter-
nal dummy load is activated and 5 W is
applied to the input port of the
attenuator. This is a great tuning
aid for the workbench.
The choice of attenuator steps is
interesting. Many attenuators are
configured to include the following
switchable pads: 3 dB, 6 dB and
several 10 dB and 20 dB pads. This
allows a wide range of attenuation.
The Xtal Set attenuator kit has a single
3 dB pad, a single 6 dB pad and two
12 dB pads. The 3 dB pad cuts the RF
signal in half and is equal to
1
⁄2 of an S unit.
A 6 dB attenuator equals 1 S unit, or a
signal decrease by a factor of four. The
12 dB pad equals 2 S units or a factor of 16.
In other words, this attenuator makes it easy
to assess S meter accuracy. It also makes
quick work out of figuring your QRPp
(power levels below 1 watt) when reducing
your transmitter output for those times you
want to play the “How low can you go”
game. You can accurately attenuate your
5 W QRP signal all the way down to
2.5 mW in 12 discrete
steps for a total of
33 dB of attenuation!
Bottom line: This Xtal
Set Society SADL
QRP attenuator is an
excellent first home-
brew/kit building
project and provides the frugal QRPer
with a very useful and interesting piece of
test equipment at an extremely attractive
price.
Manufacturer: Xtal Set Society, PO Box 3636,
Lawrence, KS 66046; tel [phone];
www.midnightscience.com. $49.95;
kit without case, $41.95.
R15 was a current limiting resistor for the
LED indicator. Past experience had shown
that a 1 kΩ resistor would be okay to use in
this application so I went ahead and used the
supplied resistor for R15 with no ill effects.
Rich Arland, K7SZ
[e-mail]
There are times that many of us need a step
attenuator to accurately control the output of
an RF generator during receiver alignment,
or to reduce the output of a QRP transmitter
for on-air testing. Let’s not forget the need
for a step attenuator for use in transmitter
hunting, where you need to drop the input
to your receiver to avoid overload as you
approach the hidden transmitter.
There have been many articles
detailing with how to build a step
attenuator. The current ARRL
Handbook has a construction project
on how to fabricate one of these inex-
pensive pieces of test gear. The obvious
hurdle to overcome is parts procurement.
Also, most of the step attenuators are not
constructed to handle more than a half
watt of input, and then only for a very short
time.
Thankfully the creative folks at the Xtal Set
Society have overcome these obstacles and
provide a nifty little kit, including a plastic
enclosure, for the paltry sum of only $49.95
plus shipping/handling. The really sweet
thing about this attenuator kit is that in
addition to a built-in dummy load with LED
indicator, it will handle a full 5 W of RF
indefinitely, making it an ideal tool for the
QRP workbench/shack. This kit can be
ordered in three configurations: complete
kit with case, kit without case and PC board
only.
Building the Kit
My QRP SADL (complete) kit arrived from
the Xtal Set Society in a small box. The PC
board was very well done with all through-
hole components, which makes an easy
build for my old eyes. All components are of
high quality. Instructions are very easy to
follow and the total build time was just short
of two hours.
The build went smoothly right up until the
very last resistor, R15. The instructions and
the parts list called for a 10 kΩ
1
⁄4 W resistor,
but the kit was furnished with a 1 kΩ
1
⁄4 W.
A quick look at the schematic showed that
Technical
by Mark Spencer, WA8SME
Short Takes
Steve Ford, WB8IMY, [e-mail]
Xtal Set Society SADL
RF Attenuator Kit
All components are of
high quality. Instructions
are very easy to follow and
the total build time was
just short of two hours.