Specification Sheet

Limited Lifetime Warranty: Sashco warrants this product will substantially meet published specications
on the date of sale. If it fails to do so, return unused portion with original sales receipt for replacement or
refund, at Sashco’s sole option. These are purchaser’s sole and exclusive remedies for any breach of war-
ranty. Purchaser must determine suitability of product for purchaser’s specic needs and assumes all risk
associated with its use. Sashco will not be liable for direct or indirect damages.
Except as stated above there are no warranties for this product. The foregoing express warranty is in
lieu of all other warranties, express or implied, including without limitation implied warranties of
merchantability or tness for a particular purpose, which warranties are specically excluded and
disclaimed. This Limited Warranty gives you specic legal rights. You may have other rights which vary
from state to state. Some states do not allow exclusion of implied warranties in consumer or other sales,
limitations on the duration of implied warranties, or exclusion or limitation of incidental or consequential
damages. Thus, the limitations or exclusions contained above may not apply to you depending upon your
specic circumstances.
Visit www.sashco.com for information on other Sashco high performance products.
typicAl properties:
Property Value
Joint Size Maximum 3” wide
Note: Use appropriate size pre-caulking ller rope (backer rod)
in any joint 1/2” deep or more.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Application Range 40°F to 120°F (4°C to 49°C) surface temperature
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Service Range -30°F to 250°F (-34°C to 121°C)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Tensile Properties Recovery at 50% stretch: 96% in 1 minute
Recovery at 100% stretch: 96% in 1 minute
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Max. Elongation 300%
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
VOC <1.5% by weight, 58 g/L, CA compliant
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
test DAtA:
Property Results Test Method
Hardness, Shore A 32 (21-day cure) ASTM C-661
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Slump < 1/8” ASTM D-2202
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Solids 78% by weight ASTM C-1250
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Extrusion Rate 750 g/min (1/8” orice at 40 psi) ASTM C-603
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Cured 1 week (dependent on temperature, ASTM C-679
humidity and bead size/thickness)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Tack-free less than 30 minutes ASTM C-679
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Low Temp. Flexibility Pass (not articially weathered) ASTM C-734
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Freeze-Thaw Stability Passes 10 cycles ASTM C-731
0˚F to 70˚F (-18°C to 21°C)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Adhesion-in-peel See “ADHERES TO” section on front page AST M C-794
Passing Substrates
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
speciFicAtions:
• Meets FHA requirements.
• Meets or exceeds Federal Specication TT-S-00230 C, ASTM C-834
The data reported here is believed to be reliable. No warranty is made concerning the accuracy of or the results
obtained from the use of this data.
Aquaseal®, Kynar® and Teon® are registered trademarks of their respective owners.
WARNING: This product contains crystalline silica sand, which is known by the State of
California to cause cancer.
Where not to Use:
• Areas of water submersion or frequent,
prolonged puddling.
• Will not adhere to or is incompatible
with Aquaseal
®
, Kynar
®
, polypropylene,
polyethylene, silicone, Teon
®
, waxes.
• Substrates not listed should be tested
for compatibility before use.
ApplicAtion:
• Use on horizontal concrete, stone or
brick surfaces that have cured for at
least 4 weeks.
• Keep foot and vehicle trafc off the
sealant for a minimum of 24 hours after
application. (Wait 48 hours in humidity
above 50% and/or cooler temps below
50°F.)
• Apply to dry surfaces with a tempera-
ture between 40°F and 120°F.
• Remove any previously applied caulk
or foams, as well as oils, dirt and other
contaminants.
• Thoroughly clean the crack with either
a stiff bristled brush or a drill-mounted
brush. Sweep or blow out any debris.
• Install Sashco’s Pre-Caulking Filler
Rope or similar backer rod in joints ½”
deep or more.
• Choose bead size and cut the nozzle.
• Gun Slab into the crack.
• Tool with water and a foam brush,
trowel, or nger to ensure adequate ad-
hesion. For best elasticity and durabil-
ity, make sure Slab is slightly recessed
after complete cure.
storAge AnD cleAn Up:
• Clean up fresh product on surfaces
and skin with soap and water.
• Tightly reseal cartridges with plastic
wrap and a rubber band. Store
between 50°F and 90°F.
First AiD: EYES: Immediately ush
with large quantities of water for at least
15 minutes. If irritation persists, see a
medical doctor. SKIN: Wash with soap
and water and rinse thoroughly. Wash
contaminated clothing after use.
INHALATION: Remove to fresh air.
INGESTION: If large quantities are swal-
lowed, DO NOT INDUCE VOMITING
- seek medical help immediately.
Keep
out of reach of children. Refer to the
MSDS for this product as needed.
SLB 007 09-12
1-800-767-5656 • www.sashco.com
10300 E. 107th Pl., Brighton, CO 80601
Made in the USA
Keep up with SashcoInc on: