Manualshelf

Operating instructions

ManualsBrandsSartorius ManualsKitchen AppliancesBasic lite
919293949596979899100
98
Pin Assignment Charts
Models CISL1 and CISL2
(IP44 protected):
Female Connectors COM1 and UniCOM:
25-contact D-Submini DB25S with
screw lock hardware
Front view
Male interface connector used
(please use connectors with the same
specifications):
25-pin D-Submini DB25, with integrat-
ed shielded cable clamp assembly (Amp
type 826 985-1C) and fastening screws
(Amp type 164868-1)
Pin assignments in COM1
Pin 1: Shield
Pin 2: Data output (TxD)
Pin 3: Data input (RxD)
Pin 4: Not connected
Pin 5: Clear to send (CTS)
Pin 6: Internally connected
Pin 7: Internal ground (GND)
Pin 8: Internal ground (GND)
Pin 9: Not connected
Pin 10: Not connected
Pin 11: +12 V for printer
Pin 12: RES_OUT\
Pin 13: +5 V
Pin 14: Internal ground (GND)
Pin 15: Universal switch
Pin 16: Control output “lighter”
Pin 17: Control output “equal”
Pin 18: Control output “heavier”
Pin 19: Control output “set”
Pin 20: Data terminal ready (DTR)
Pin 21: Ground (GND)
Pin 22: Not connected
Pin 23: Not connected
Pin 24: +15...25 V
Pin 25: +5 V
Models CIS1 and CIS2:
Terminals on the PCB
COM1: 11-20 1-10
Pin assignments in UniCOM:
Connecting external battery pack/
bar code scanner
1)
(optional
UNICOM interface not installed)
Pin 1: Shield
Pin 2: Not connected*
Pin 3: Not connected*
Pin 4: Internal ground (GND)
Pin 5: Not connected
Pin 6: Not connected*
Pin 7: Not connected*
Pin 8: Not connected*
Pin 9: Not connected*
Pin 10: Not connected*
Pin 11: +12 V for printer
Pin 12: RES_OUT\
Pin 13: +5 V Switch
Pin 14: Internal ground (GND)
Pin 15: Keyboard data
Pin 16: Not connected*
Pin 17: Not connected*
Pin 18: Not connected*
Pin 19: Keyboard clock
Pin 20: Not connected*
Pin 21: LINE_1_GND
Pin 22: LOW_BATT
Pin 23: BATT_ON_OFF
Pin 24: LINE_1_B
Pin 25: +5 V
1)
Combics 2 models only
* depends on the UniCOM used
UniCOM: 1-4 1-10
Models CIS1 and CIS2
(IP65/67 protected):
Connecting open cable ends to the
terminal screws in the indicator
COM1 interface connection:
Top view
Terminal assignments
No. 1: Universal switch
No. 2: Control output “set”
No. 3: Control output “heavier”
No. 4: Control output “equal”
No. 5: Control output “lighter”
No. 6: Clear to send (CTS)
No. 7: Data output (TxD)
No. 8: Data input (RxD)
No. 9: Data terminal ready (DTR)
No. 10: Internal Ground (GND)
No. 11: LINE_A
No. 12: LINE_A
No. 13: GND_LINE_A
No. 14: GND_LINE_A
No. 15: +12 V for printer
No. 16: Reset_Out
No. 17: +5 V
No. 18: +5 V
No. 19: Ground (GND)
No. 20: Ground (GND)