User Manual

Joule 2.0 User Guide page 54
Joule 2.0 User Guide page 55
Chapter 7: Setting Up CycleOps Joule 2.0
Roll Down Calibration for CycleOps PowerBeam Pro Trainer
The CycleOps PowerBeam Pro resistance unit is calibrated at the factory. This enables it to ac-
curately measure power using similar technology as a PowerTap. Rolling resistance is calibrated
into each individual resistance unit, but can vary depending on tire type, tire pressure, clamping
pressure and other conditions. To obtain the most accurate results, follow these guidelines:
• PerformtheManualCalibrationdescribedbelow.
• Inflatetirestotheratedpressure.
• AttachthebicycleaccordingtothePowerBeamProtraineruserguide
• ClamptheresistanceunittothereartireaccordingtothePowerBeamProtraineruser
guide
• Formountainbicycles,usesmoothtires.Knobbytiresarenoisyandcontributetoinac
curacies.
1.Before entering the calibration routine, warm up the PowerBeam Pro and tires by riding the system for five
minutes.
1. Press and release the [MODE] button until Menu mode is displayed.
3. Press [JOYSTICK] in and release to select Sensors.
4. Press [JOYSTICK] up/down to highlight RU Sensor. Press [JOYSTICK] in and release to select RU Sensor.
5. Press [JOYSTICK] up/down to highlight the active RU Sensor. Note: the active RU Sensor is indicated by a
hash mark next to the name in the RU Sensor list. Press [JOYSTICK] in and release to select the active RU Sensor.
6. Press [JOYSTICK] up/down to highlight Calibration. Press [JOYSTICK] up/down to select Calibration.
7. Press [JOYSTICK up/down to highlight Roll Down calibration. Press [JOYSTICK] in and release to select Roll
Down calibration.
Chapter 7: Setting Up CycleOps Joule 2.0
Roll Down Calibration for CycleOps PowerBeam Pro Trainer...continued
8. Once selected, the roll down calibration process will begin with instructions to pedal at 18 mph.
9. Once at 18 mph, hold this speed for two minutes. A count down timer displays your remaining time.
10. After two minutes, immediately stop pedaling and allow the bicycle wheel to coast to a complete stop.
11. Do not touch or disturb the resistance unit while coasting. Do not pedal or apply the brakes while coasting.
12. After the resistance unit comes to a complete stop, a “Calibration Passed” message will be shown. Note: if
you do not wait the full two minutes or another issue occurs during calibration, a “Calibration Failed” message
will be shown and calibration must be repeated. Note: If calibration continues to fail, contact Saris Cycling
Group at 1-800-783-7257.
13. The unique rolling resistance calibration is now incorporated into the factory calibration. This calibration will
remain in the system until another calibration is performed.
OK
>
Name:
>
12345
>
12345
>
Weight - lbs:
>
12.1
>
Wheel Circumference:
>
1234
>
Auto Zero (Y or N):
>
Y
>
>
Auto Zero (Y or N):
>
Cervelo
>
Sensor ID:
>
12345
>
Calibration
>
ERU Data
>
Re-Pair Sensor
>
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Back
<
Report
Menu
INT
PowerBeam1
Scenerio:
ERU Calibration
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Back
<
Report
Menu
INT
Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Calibration
Pedal to 18-22 MPH
>
XX
Hold for (sec):
XXX
Current Speed:
XX.X
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair
>
Completed
>
Back
<
Report
Menu
INT
Roll Down
Use up/down to
>
match ERU to power
sensor number.
Tu:
XXXXX
ERU Power:
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
XXX
>
Power Sensor:
XXX
>
Back
<
Report
Menu
INT
Manual Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Calibration
Restoring Defaults
>
match ERU to power
sensor number.
ERU Power
Completed
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Completed
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Reset Calibration
Tu is the only user
selectable field.The
Joystick up/down causes
the Tu value to
increase/decrease in steps
of fifty.
Activate Sensor
>
Name:
>
12345
>
12345
>
Weight - lbs:
>
12.1
>
1234
>
Auto Zero (Y or N):
>
Y
>
>
RUSENSOR1
>
Sensor ID:
>
60054
>
>
>
>
>
Delete Sensor
>
>
>
>
Back
<
Report
Menu
RUSensor1
Cancel Pairing
Delete Sensor
RU Data
Calibration
>
>
Start Pairing
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Back
Report
Menu
Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
Calibration
Pedal to 18-22 MPH
>
XX
Hold for (sec):
XXX
Current Speed:
XX.X
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair
>
Completed
>
Back
<
Report
Menu
Roll Down
Use up/down to
>
match ERU to power
sensor number.
Tu:
XXXXX
ERU Power:
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
XXX
>
Power Sensor:
XXX
>
Back
<
Report
Menu
Manual Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
Calibration
Restoring Defaults
>
match ERU to power
sensor number.
ERU Power
Completed
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Completed
>
Pair New Sensor
>
Back
<
Report
Menu
Reset Calibration
OK
>
Name:
>
12345
>
12345
>
Weight - lbs:
>
12.1
>
Wheel Circumference:
>
1234
>
Auto Zero (Y or N):
>
Y
>
>
Auto Zero (Y or N):
>
Cervelo
>
Sensor ID:
>
12345
>
Calibration
>
ERU Data
>
Re-Pair Sensor
>
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Delete Sensor
>
Back
<
Report
Menu
INT
PowerBeam1
Scenerio:
ERU Calibration
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Back
<
Report
Menu
INT
Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Calibration
Pedal to 18-22 MPH
>
XX
Hold for (sec):
XXX
Current Speed:
XX.X
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair
>
Completed
>
Back
<
Report
Menu
INT
Roll Down
Use up/down to
>
match ERU to power
sensor number.
Tu:
XXXXX
ERU Power:
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
XXX
>
Power Sensor:
XXX
>
Back
<
Report
Menu
INT
Manual Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Calibration
Restoring Defaults
>
match ERU to power
sensor number.
ERU Power
Completed
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Completed
>
Pair New Sensor
>
Back
<
Report
Menu
INT
Reset Calibration
Tu is the only user
selectable field.The
Joystick up/down causes
the Tu value to
increase/decrease in steps
of fifty.
Activate Sensor
>
Name:
>
12345
>
12345
>
Weight - lbs:
>
12.1
>
1234
>
Auto Zero (Y or N):
>
Y
>
>
RUSENSOR1
>
Sensor ID:
>
60054
>
>
>
>
>
Delete Sensor
>
>
>
>
Back
<
Report
Menu
RUSensor1
Cancel Pairing
Delete Sensor
RU Data
Calibration
>
>
Start Pairing
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Back
Report
Menu
Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
Calibration
Pedal to 18-22 MPH
>
XX
Hold for (sec):
XXX
Current Speed:
XX.X
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair
>
Completed
>
Back
<
Report
Menu
Roll Down
Use up/down to
>
match ERU to power
sensor number.
Tu:
XXXXX
ERU Power:
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
XXX
>
Power Sensor:
XXX
>
Back
<
Report
Menu
Manual Calibration
Power Sensor: 9999 w
>
>
Roll Down Calibration
Wheel Circumference
>
Wheel Circumference
>
The Gun Show
>
Auto Zero
>
Auto Zero
>
Pair
>
Roll Down
>
Manual
>
Reset to Defaults
>
Sensor ID
Sensor ID
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Pair New Sensor
>
Back
<
Report
Menu
Calibration
Restoring Defaults
>
match ERU to power
sensor number.
ERU Power
Completed
The Gun Show
>
To rque Offset
>
Manual Calibration
>
To rque Offset
>
Completed
>
Pair New Sensor
>
Back
<
Report
Menu
Reset Calibration