PG PASSPORT 1000 Exit Device Installation Instructions A7809B 10/12 Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents 1 Warning . ....................................................................................... 2 2 General Description....................................................................... 3 3 Hardware Specifications............................................................... 3 4 Electronic Specifications............................................................... 3 5 Part Breakdown.............................................................................
Passport 1000 PG Exit Device 2 General Description Designed specifically for the campus market, the SARGENT Passport 1000 PG Rim/Mortise Exit Device (powered by PERSONA) provides offline card/PIN access control, as well as detailed audit capabilities. • The PG stand alone unit is available with both keypad and magstripe card technology, or magstripe only. • The PG operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor applications.
Passport 1000 PG Exit Device PG Standalone With Card Insert and/or Keypad 13 16 3 2 9 8 5 6 10 7 13 12 11 5 14 15 13 17 18 4 PART No.
Passport 1000 PG Exit Device Parts Breakdown (Continued) 8877/8878 x ET x Lever Design Passport 1000 Rim Exit Device 4 5 6 6 6 7 3 10/31/12 Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 1 2 ITEM PART No.
Passport 1000 PG Exit Device Parts Breakdown (Continued) 8977/8978 x ET x Lever Design Passport 1000 Mortise Exit Device 7 7 8 7 6 5 4 3 2 ITEM PART No.
Passport 1000 PG Exit Device 6 Installation Instructions for 8977/8978 Rim Exit IMPORTANT: BEFORE STARTING • This device is non-handed. • Door should be fitted and hung. • Verify box label for size of exit device, function and hand. 1 – Exit Hardware & Door Preparation If using a mullion, install in frame. Prior to installation, all holes must be free of burrs, debris and sharp edges. If doors are not properly reinforced per ANSI 115.2, commercially available reinforcements should be installed.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) 2 – Installation of Exit Trim (ET), Exit Chassis and Cylinder A. Outside Trim 1. For exterior applications, “ET” gasket (52-0263) should be used to seal between “ET” escutcheon and outside door surface. 2. Route harness through under cut of cylinder hole and out to other side of door. 3. Place “ET” control onto door. Outside of door ET Wire harness (from motor) ET gasket ET control 3.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) Outside of door 2 – Installation of Exit Trim (ET), Exit Chassis and Cylinder (continued) C. Cylinder Installation Note: For devices without cylinder, go to Step 2D. 1. Insert cylinder into “ET” control. 2. Mate cylinder tailpiece into hub of exit device chassis. 3. Make sure “ET” harness is clear of cylinder and cylinder tailpiece. #34 CYLINDER Fig.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) Inside of door 3 - Chassis Cover Instructions Secure chassis cover to chassis using (4) #8-32 x 5/16” oval head machine screws. Chassis Cover (4) #8-32 x 5/8” oval head machine screws Fig. 3A 4 - Wire Cover Instructions (Wood doors only) 1. Align wire cover plate with chassis side against exit chassis cover and mark hole positions. 2. Drill (2) 3/32” diameter by 1/2” deep holes as shown (Fig. 4A1). 3.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) 5B – Installation of Outside Escutcheon & Mounting Plate Assembly 1. Insert the mounting posts through holes as shown (Fig. 5B1). 2. On the inside of the door, position the mounting plate over the indicated holes. As you feed controller, keypad, battery and grounding cables thru side opening (Fig. 5B1), tuck the ferrite bead safely under the reader.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) Modular component 6A – Installation of Inside Component Assembly 1. Insert bottom of component assembly first (Fig. 6A). 2. Clip top of component assembly to mounting plate verifying both tabs attached securely. Inside of door Fig. 6A 6B - Installation of Connectors Secure the following connectors onto the circuit board (Fig. 6B1 and 6B2): 1. Secure the mortise lock body assembly connector (10-pin). 2.
Passport 1000 PG Exit Device Rim Installation Instructions (Continued) 7 - Battery/Battery Pack Installation Battery pack 1. Place (6) “AA” batteries into the compartment being careful to align polarity (- & +) according to case markings. PERSONA PG controller DIP switch location 2. Insert battery pack and click into place, making sure polarity terminals on the battery pack are oriented upward (Fig. 7A). 3. Verify DIP switch settings are correct for the application.
Passport 1000 PG Exit Device 7 Installation Instructions for Mortise Type Exit Device 8977/8978 IMPORTANT BEFORE STARTING: • This device is non-handed. • Door should be fitted and hung. • Verify box label for size of exit device, function and hand. Inside Left Hand Reverse LHR Outside Right Hand Reverse RHR 1 – Exit Hardware and Door Preparation If using a mullion, install in frame. Prior to installation, all holes must be free of burrs, debris and sharp edges.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) 2 – Installation of Outside Exit Trim (ET), Exit Chassis and Cylinder A. Outside Trim 1. Slide mortise lock into door and securely fasten with (2) flat head screws. 2. For exterior applications, gasket (52-0263) should be used to seal between “ET” escutcheon and outside door surface. 3. Route “ET” harness through wire cutout and out other side of door. 4. Place “ET” control on door with spindle inserted through mortise lock.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) 2 – Installation of Outside Trim, Exit Chassis and Cylinder (Continued) B. Exit Chassis (Continued): Fasten exit chassis to door using (4) #10 wood screws or #10-24 machine screws (Fig. 2B3). Inside of door 10/31/12 Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) 3 – Chassis Cover Instructions Inside of door Secure chassis cover to chassis using (4) #8 - 32 x 5/16” oval head machine screws. Chassis cover (4) #8 - 32 x 5/16” Oval head machine screws 4 - Wire Cover Instructions (Wood Door Only) Back side of wire cover plate This side down Inside of door Wire cover (2) 3/32” dia. by 1/2” deep holes (2) #6 x ½” flat head security Torx wood screws Fig.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) Outside of door 5A – Installation of Outside Escutcheon with Weatherseal Gasket (optional) Note: For non-fire rated door applications, an optional gasket may be used as a weatherseal between the escutcheon and the outside door surface. Peel off adhesive backing and attach to (outside) escutcheon (Fig. 5A). Passport gasket Outside Passport trim 5B – Installation of Outside Escutcheon & Mounting Plate Assembly Fig. 5A 1.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) Modular component 6A – Installation of Inside Component Assembly 1. Insert bottom of component assembly first (Fig. 6A). 2. Clip top of component assembly to mounting plate verifying both tabs attached securely. Inside of door Fig. 6A 6B - Installation of Connectors Secure the following connectors onto the circuit board (Fig. 6B1 and 6B2): 1. Secure the mortise lock body assembly connector (10-pin). 2.
Passport 1000 PG Exit Device Mortise Installation Instructions (Continued) 7 - Battery/Battery Pack Installation and DIP Switch Verification 1. Place (6) “AA” batteries into the compartment, being careful to properly align polarity (- & +) . 2. Insert battery pack and click into place making sure polarity terminals on the battery pack are oriented upward as in Fig. 7A. 3. Verify DIP switch settings are correct for the application.
Passport 1000 PG Exit Device 8 Setting up the Locklink™ and Contact Card for First Use* *NOTE: The following steps in this section are only performed one time. Once Bluetooth pairing is complete, these steps do not need to be repeated to program locks (Section 8 ”Lockset Programming”). Pairing the Pocket PC with the Contact Card 1.To begin, highlight (by tapping) the select the ‘Settings’ menu. button and 3.
Passport 1000 PG Exit Device 4. The Pocket PC will enable Bluetooth and begin discovery. If you receive a warning, "No Devices Found," then check again to see the blue light flashing on the contact card and tap ‘Retry’ . If the blue light is not flashing, remove the contact card, wait for the lights to go dark, then reinsert it before tapping ‘Retry’. If this step fails repeatedly, then contact PERSONA technical support at (800)–481–8464.
Passport 1000 PG Exit Device 9 Lockset Programming 1. Tap then tap to launch the LockLink program. Choose Menu and then ‘Setup’. 2. Pick the COM port noted in Step 6. Check the box ‘Use Bluetooth’ and click ‘Apply’. Start the PERSONA LockLink™ software: 1. Tap the Start button on the Pocket PC Screen. 2. If visible, select PERSONA LockLink™ to launch the program; otherwise, tap Start and Programs to launch the Programs list and then select the PERSONA LockLink™ icon (right). 4. Type in your password.
Passport 1000 PG Exit Device Lockset Programming Instructions (Continued) Upload Full Program After locks are installed, they must have program files copied into them before they can receive and interpret data. In many ways, the program files act as the locks’ operating system by interpreting the lock data to control each lock’s behavior. 1. Highlight (by tapping) the name of the lock that you wish to program.
Passport 1000 PG Exit Device Lockset Programming Instructions (Continued) 6. Reinsert Contact Card a second time to initialize the program. Note: You should hear the motor run briefly. 8. Follow the on-screen directions and reinsert the Contact Card a third time. A7809B 25 10/31/12 Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 7.
Passport 1000 PG Exit Device Lockset Programming Instructions (Continued) 9. Remove the Contact Card. 10. To exit and return to the program screen, tap the button. 11. After programming the new lockset, verify operation by performing the Operational Check (refer to Section 9). 12. Repeat this procedure for each lock to be programmed with lock data. 10/31/12 Copyright © 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Passport 1000 PG Exit Device Operational Check IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For devices with cylinders, the following checks apply: Insert key into cylinder and rotate: a. There should be no friction against lock case, wire harness, or any other obstructions.
Sargent Manufacturing Company 100 Sargent Drive New Haven, CT 06511 USA PERSONA Technical Support: 800-481-8464 • www.personacampus.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.
