Installation Instructions FM7100 Series Multi-Point Lock For installation assistance, contact SARGENT at 800-727-5477. RH Door Shown INSIDE INSIDE INSIDE INSIDE OUTSIDE OUTSIDE OUTSIDE OUTSIDE RIGHT HAND (RH) LEFT HAND (LH) A8010C (11/13) RIGHT HAND REVERSE (RHR) LEFT HAND REVERSE (LHR) Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Tools Supplied This device is intended to be part of an integrated door, frame and hardware assembly ULapproved for both FEMA 361 and FEMA 320 guidelines for both inswing and out-swing doors.
VERIFY HANDING Right Hand Door Shown INSIDE OUTSIDE Left Hand Door Shown A8010C (11/13) 3 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
VERIFY DOOR DIMENSIONS WARNING LOCK IN condition can occur and EMERGENCY EGRESS will be prevented if critical dimensions are not met. ! Device will not operate, if door cutouts are not within the dimensions below. 40 41 42 43 44 45 46 INSIDE 42" - 42-3/4" OUTSIDE Right Hand Door Shown 37-1/2" - 38-1/4" 36 37 38 39 40 41 42 43 If door does not match above dimensions, contact door manufacturer.
1. INSTALL DEADBOLT ASSEMBLY (2) Flat Head Hex Socket 1/4-20x1" Right Hand Door Shown FM7100 ! WARNING Deadbolt must be retracted before moving to the next step. A8010C (11/13) 5 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
2. INSTALL BOTTOM BOLT ASSEMBLY (3) Flat Head Hex Socket 12-24x1" 1 Right Hand Door Shown A8010C (11/13) FM7100 2 6 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
3. ALIGN BOTTOM BOLT ASSEMBLY Right Hand Door Shown 1 0 0 1 7 OR F M 2 SH PU 2 DOWN 3 UP SH PU A8010C (11/13) 7 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
4. PREP TOP ASSEMBLY 1 2 LAY TOP ROD ON DOOR 3 FM7100 Right Hand Door Shown 4 A8010C (11/13) MARK CLOSEST HOLE 8 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
5. INSTALL TOP ASSEMBLY FM7100 (2) Flat Head Hex Socket 12-24x1" FM7100 Right Hand Door Shown A8010C (11/13) 9 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
6. ALIGN TOP & BOTTOM ROD PINNING HOLES Right Hand Door Shown 2 SH F M PU 0 0 1 7 1 Top Rod GO TO STEP 7 Bottom Rod GO TO STEP 6a OR 6b A8010C (11/13) 10 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
6a. ADJUST MISALIGNED PINNING HOLES UP Right Hand Door Shown 2 SH F M PU 0 0 1 7 1 Top Rod Bottom Rod 3 = 4 GO TO STEP 7 A8010C (11/13) 11 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
6b. ADJUST MISALIGNED PINNING HOLES DOWN Right Hand Door Shown 2 SH F M PU 0 0 1 7 1 Top Rod Bottom Rod 3 = 4 GO TO STEP 7 A8010C (11/13) 12 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
7. PIN THREE ASSEMBLIES (1) Drive Pin (1) Push-on Retaining Ring INSIDE OUTSIDE FM 00 FM7100 1 71 2 Right Hand Door Shown 8. MOUNT DOOR TO FRAME ! Do not trim door if door rubs along floor! FM7100 Right Hand Door Shown A8010C (11/13) 13 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
9. CHECK FOR HOLD OPEN 1 0 FM710 0 FM710 PUSH GO TO STEP 10 2 0 FM710 3 A8010C (11/13) 14 of 20 GO BACK TO 1 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
10. ADJUST DEVICE 1 ! Hand Tighten ! Device Must Be In HOLD OPEN Before Adjusting Device 2 ! = 3x Must Rotate Exactly 3 Revolutions A8010C (11/13) 15 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
11. TRIGGER DEVICE & FINAL CHECK 1 2 0 FM710 PU SH PUSH 3 FM7100 0 FM710 0 FM710 GO BACK TO STEP 10 GO BACK TO STEP 10 A8010C (11/13) 16 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
12. ASSEMBLE CYLINDER INTO OUTSIDE TRIM 13. MOUNT OUTSIDE AND INSIDE TRIM INSIDE (4) Oval Head Phillips 12-24x1 1/2" A8010C (11/13) OUTSIDE FM7100 17 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
14. INSTALL TOP LATCH INTO DOOR FRAME (4) Flat Head Hex Socket 1/4-20x1" FM7100 15. ATTACH DEADBOLT STRIKE PLATE TO FRAME (2) Flat Head Hex Socket 1/4-20x1" FM7100 A8010C (11/13) 18 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
16. PREPARE FLOOR FOR BOTTOM STRIKE 1 a 1 2 b 9 (2) Flat Head Hex Socket 1/4-20x1" c d 1 1 2 2 2 e 3 1-1/8" Dia. x 7/8" Deep A8010C (11/13) 19 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
17. INSTALL BOTTOM STRIKE 2 1 1/4" MAX Bottom Of Door To Top of Strike O optional 3/8" Dia. x 1-1/2" Deep 3 1/8" Deep 18. TEST INSTALLATION FM7100 A8010C (11/13) 20 of 20 Copyright ©2013, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
