SmartRig+ Two-channel Mic&Guitar Interface For DSLR cameras, camcorders, iOS and Android devices
Product Introduction 1 General Introductions The Saramonic SmartRig+ is a microphone/guitar interface for recording sound. It allows you to connect professional microphones/guitars to create music with your iPhone, iPad, iPod touch and Android devices, or record quality audio to your DSLR cameras and camcorders. The SmartRig+ makes your recording work much easier. It provides 48V phantom power for microphones and 3.5mm headphone output for real-time monitoring.
2 Highlights • Two XLR mic inputs • Two 1/4" (6.35mm) guitar inputs • Two 1/8" (3.5mm) inputs • Mono/Stereo switch (M/S) • Camera/Phone switch • +48V phantom power • 3.
3 Specifications Frequency Response 20 Hz to 20 Khz, +/-0.5 dB THD less than 0.01% @ 1 kHz, -30 dBu input SNR 80 dB @ 1 kHz, -30 dBu input 1x XLR mic input Input1 1 x 1/4" (6.35mm) guitar input 1 x 1/8" (3.5mm) input" 1 x XLR mic input Input2 1 x 1/4" (6.35mm) guitar input 1 x 1/8" (3.5mm) input" Output 1 x 1/8" (3.5mm) CAB LINE Phone OUT 1 x 1/8" (3.
4 Product Structure Ԯ Input1: For Microphone: One balanced XLR input One 1/8" (3.5mm) mono input For Guitar: One 1/4" (6.35mm) mono standard input ԯ Input2: For Microphone: One balanced XLR input One 1/8" (3.5mm) mono input For Guitar: One 1/4" (6.35mm) mono standard input Note: Other instruments with 1/4’’ (6.35mm) input connector can also be used with the SmartRig+.
M/S switch Select mono/stereo output mode When recording on one channel, use the mono (M) setting. The signal will be sent to both left and right channels. When recording on two channels, use the stereo (S) setting. The level of each channel can be controlled individually. Ա and Ύ Control Knobs Adjust the signal level of each channel to the optimum recording levels. Knob controls the volume of input group 1 and knob Ύ is for input group 2.
Գ LED Indicator When turn on the SmartRig+, the green indicator is on. When choose +48V phantom power, the red and green indicators are both on. When it is low battery, the red and green indicators will be dim. Դ ON/OFF/+48V Switch Select the ON/OFF switch to turn on/ off the SmartRig+. Select +48V phantom power for microphones that require phantom power to operate. Please notice that only the XLR inputs offer +48V phantom power, the 1/8" (3.5mm) mic inputs do not offer +48V phantom power.
5 Quick Start Guide a. Install a 9V battery. Gently slide out the battery cover in the direction of the arrow at the back of unit. Insert the battery with the “+” positive terminal lined up with the “+” indicator on the battery compartment. b. Connect your microphones to the XLR inputs or 3.5mm inputs, or connect guitars to the 1/4" (6.35mm) inputs. c. Set the M/S switch When recording on one channel, switch to the mono (M) setting. The signal will be sent to both left and right channels.
g. If your microphone needs phantom power, please slide the power switch to the +48V position. The red and green indicators are both on. h. Please connect your headphone to the headphone jack in case you need to monitor recording. i. You are now ready to record. Adjust the two gain controls flexibly to get the optimum signal levels. 6 Tips • Be careful not to turn the phantom power ON when recording with microphones that do not operate on phantom power, as the current may damage it.
7 Compatibility Compatible with iPhone/iPad/iPod touch, Android devices, all DSLR cameras and camcorders with 3.5mm mic input connector. Any types of microphones: Dynamic, Ribbon, or Condenser. Guitars: All guitars with 6.35mm input connector.
www.saramonic.com The Saramonic logo is trademark which is registered and owned by Saramonic International. COPYRIGHT 2011-2021 SARAMONIC INTERNATIONAL ( A brand of DSQN ) Email: info@saramonic.
