SmartRig+ UC Two-channel Mic & Guitar Interface For USB Type-C Devices
Product Introduction 1 General Introductions The Saramonic SmartRig+ UC is a two channel audio interface. It allows you to connect professional microphones/guitars to record quality sound or create music with your USB Type-C devices. The USB Type-C connector allows you to record great stereo sound to your devices. The SmartRig+ UC makes your recording work much easier. It provides 48V phantom power for microphones and 3.5mm headphone output for real-time monitoring.
2 Highlights • Two XLR mic inputs • Two 1/4" (6.35mm) guitar inputs • Two 1/8" (3.5mm) inputs • Mono/Stereo switch (M/S) • REC/PLAY switch • +48V phantom power • 3.
3 Specifications Frequency Response 20 Hz to 20 Khz, +/-0.5 dB THD less than 0.01% @ 1 kHz, -30 dBu input SNR 80 dB @ 1 kHz, -30 dBu input 1x XLR mic input Input1 1 x 1/4" (6.35mm) guitar input 1 x 1/8" (3.5mm) input 1 x XLR mic input Input2 1 x 1/4" (6.35mm) guitar input 1 x 1/8" (3.5mm) input Output USB Type-C connector output cable Phone OUT 1 x 1/8" (3.
4 Product Structure Input1: For Microphone: One balanced XLR input One 1/8" (3.5mm) mono input For Guitar: One 1/4" (6.35mm) mono standard input Input2: For Microphone: One balanced XLR input One 1/8" (3.5mm) mono input For Guitar: One 1/4" (6.35mm) mono standard input Note: Other instruments with 1/4’’ (6.35mm) input connector can also be used with the SmartRig+ UC.
M/S switch Select mono/stereo output mode When recording on one channel, use the mono (M) setting. The signal will be sent to both left and right channels. When recording on two channels, use the stereo (S) setting. The level of each channel can be controlled individually. and Control Knobs Adjust the signal level of each channel to the optimum recording levels. Knob controls the volume of input group 1 and knob is for input group 2.
When choose +48V phantom power, the red and green indicators are both on. When it is low battery, the red and green indicators will be dim. ON/OFF/+48V Switch Select the ON/OFF switch to turn on/off the SmartRig+ UC. Select +48V phantom power for microphones that require phantom power to operate. Please notice that only the XLR inputs offer +48V phantom power, the 1/8" (3.5mm) mic inputs do not offer +48V phantom power.
5 Quick Start Guide a. Install a 9V battery. Gently slide out the battery cover in the direction of the arrow at the back of unit. Insert the battery with the “+” positive terminal lined up with the “+” indicator on the battery compartment. b. Connect your microphones to the XLR inputs or 3.5mm inputs, or connect guitars to the 1/4" (6.35mm) inputs. c. Set the M/S switch When recording on one channel, switch to the mono (M) setting. The signal will be sent to both left and right channels.
The red and green indicators are both on. h. Connect your headphone to headphone jack to monitor the recording. Set the REC/PLAY switch When you need to monitor audio directly from the microphone or audio sources when recording, slide to REC. When you need to monitor playback audio from the USB Type-C devices, slide to PLAY. i. You are now ready to record. Adjust the two gain controls flexibly to get the optimum signal levels.
7 Compatibility Compatible with USB Type-C devices (Except GoPro USB Type-C). Any types of microphones: Dynamic, Ribbon, or Condenser. Musical instrument: Guitars or other musical instruments with a 6.35mm input.
www.saramonic.com The Saramonic logo is trademark which is registered and owned by Saramonic International. COPYRIGHT 2011-2021 SARAMONIC INTERNATIONAL ( A brand of DSQN ) Email: info@saramonic.
