Installation Manual Sapling Horizontal Time Zone Clocks The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Sapling Horizontal Time Zone Clocks - Table of Contents Interactive Hyperlinked PDF – Click on the topic and the document will go to the relevant page. Clicking on the logo will take you back to the table of contents.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Important Safety Instructions ! WARNING ! DANGER , SHOCK HAZARD • • Keep the electricity to this device turned OFF until the clock installation is complete. Do not expose the clock movement to water, or install the clock in a location where it may be exposed to water. NOTICE • • • Do not install the clock outdoors.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Configuring a Clock to be Used in a Zone Clock The below instructions are to be followed ONLY after initial mandatory clock settings have been configured (such as network settings) per the clock installation manual (which will depend on its series). These instructions are provided specifically to set each clock with its time offset and DST (daylight savings time) settings.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Configuring a Clock to be Used in a Zone Clock IP-PoE and Wi-Fi Systems (continued) Clocks for IP-PoE and Wi-Fi Zone Clocks are configured by the user. EACH CLOCK MUST BE CONFIGURED INDIVIDUALLY BY THE USER UNLESS PRESET SERVICE WAS ORDERED. Consult the manual for instructions on how to log in to each clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole Included in Package Description Quantity 1 1) Zone Clock Pole 2) Mounting Bases Picture (Shown below. The pole length may vary depending on the number and type of clocks.) 2 (Depending on Pole Length) 3) Mounting Template 1 Example: (Shown below. The template content may vary depending on the number and type of clocks) 60.0" [152.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 1 1) Determine where you wish to install the zone clock by using the provided mounting template as a guide. Use a level to confirm that the horizontal line on the template is level with the floor. The amount of space that you must leave between the template and the ceiling or walls depends on the type of clock purchased.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 2 3 2) Locate the positions of the outer holes on each mounting plate. Use a drill to create each hole through the template. 3) Skip this step if your clock is battery-powered. Use a pencil to poke through the template and find the position of each inner hole. Mark each position on the wall.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 6 6) Insert the machine screws through the mounting plates and into the gang boxes, then insert the self-tapping screws through the mounting plates and into the wall anchors. Holes A, B, C, and D are meant for securing the base plate to a standard double gang (utility) box.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 8 8) Skip this step if your clock is battery-powered. Thread wiring through the mounting plate. If the wires are NOT Power over Ethernet, attach grounding wires to mounting plates using green screws. Electrical Wiring Network Cables * Power wires should extend far enough from the gang box to reach the first clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 10 10) Thread wiring through the bases, then attach the bases to the mounting plates.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 11 11) Attach the housings to the sliding nuts on the zone clock pole. Use the black M4-0.5x10 screws and internal-tooth washers for each housing until each housing is attached. Round and Digital housings require four screws and four washers per housing. Square clocks require six screws and six washers per housing.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 12 13 12) Skip this step if your clock is battery-powered or uses Power over Ethernet. Attach the grounding screw to the hole in the zone clock pole. Leave some space between the head of the screw and the pole so that the grounding cable can be attached later.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 14 14) Skip this if your clock is battery-powered. Attach the wires that have been threaded into each adapter to one of the supplied connectors. Consult your clock manual for instructions on how to properly wire the other clocks. If your clock uses Power over Ethernet, use a crimp tool to insert the CAT5/CAT6 wires into the RJ45 connector.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Mounting a Zone Clock Pole 15 15) Skip this if your clock is battery-powered or uses Power over Ethernet. Attach the grounding wire to the green grounding screw. Once the wire is wrapped around the screw, tighten the screw so that the grounding wire is held firmly between the screw head and the surface of the pole. 16 16) Run wiring or IP cables to the remaining clocks.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Attaching the Name Plates The name plates are attached to the pole by sliding the upper latch underneath the back-upper lip of the mounting pole (1), then swinging the bottom of the plate forward (2) until the lower latch catches onto the back-lower lip of the pole (3).
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Warranty Sapling Limited Warranty and Disclaimer The Sapling Company, Inc.
