Dump Switch 5 Port Smart Fast Ethernet Switch HF-3205 Networking User Manual v1.0.
FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions Frequency range - 2400.0 - 2483.5 MHz Country Bulgaria France Italy Luxembourg Norway Russian Federation Country Reason/remark General authorization required for outdoor use none and public service. Military Radiolocation use. Refarming of the 2.
TABLE OF CONTENTS 1 GETTING TO KNOW THE SWITCH 5 1.1 Introduction 1.2 Key Features 1.3 The Front Panel 1.3.1LEDs status 1.4 The Rear Panel 1.4.1Power Connector 1.4.2Network Ports 1.4.3Cabling 1.4.4QoS Switch 5 5 6 6 7 7 7 7 7 2 USEFUL TIPS 9 2.1 Prior to Installation 2.2 Half- and Full-Duplex 2.3 Auto-Negotiation 9 9 9 3 PRODUCT SPECIFICATIONS http://www.sapido.com.tw/ 11 4 User Manual v1.0.
1 Getting to know the Switch 1.1 Introduction The Fast Ethernet Switch is equipped with 5 100Mbps copper ports and each port provides a max speed of 200Mbps and a Full-Duplex, Collision Free Bandwidth. It’s a multi-speed, versatile network device that combines Fast Ethernet, and Ethernet ports in a single device. This device meets RoHS compliance. It saves power with Green Ethernet technology. 1.
1.3 The Front Panel 1.3.1 LEDs status Information about the Switch’s activity is displayed through its LEDs, shown as below. LED Function Color Status Description Green On Power is being applied to this product Power x1 Power indication Red Port x 5 Blinking Loop detected On Connected at 10/100Mbps Ethernet port activity and loop Green Blinking 10/100Mbps Tx/Rx activity status Blinking Loop detected http://www.sapido.com.tw/ 6 User Manual v1.0.
1.4 The Rear Panel 1.4.1 DC QoS Mode Input Switch Power Connector The power connector is designed to be used with the power adapter included in the product package. 1.4.2 Network Ports The Switch is equipped with five RJ-45 ports that support network speeds of 10/100Mbps. 1.4.3 Cabling 100Mbps - To transmit at 100Mbps requires Cat. 5 cabling. 10Mbps - When transmitting at 10Mbps, Cat. 3, 4 or 5 TP cabling with RJ-45 sockets can be used. Port Type Cable Type Connector 100BASE-TX Cat.
Port 1 －＞ Normal Priority ( Red ) Port 2 －＞ Normal Priority ( Yellow ) Port 3 －＞ Normal Priority ( Yellow ) Port 4 －＞ Normal Priority ( Green ) Port 5 －＞ Normal Priority ( Green ) Auto control mode Port 1 －＞ Most High Priority ( Red ) Port 2 －＞ More High Priority ( Yellow ) Port 3 －＞ More High Priority ( Yellow ) Port 4 －＞ High Priority ( Green ) Port 5 －＞ High Priority ( Green ) http://www.sapido.com.tw/ 8 User Manual v1.0.
2 Useful Tips 2.1 Prior to Installation Before installing the switch and connecting network devices, it is important to plan the network's layout. Things you should consider include: ．Dedicated Bandwidth: File servers and other high-traffic hardware will have better and improved performance if they have their own dedicated 10Mbps, or 100Mbps bandwidth. ．Full-Duplex: Determine which devices support Full-Duplex connections. ．Fast Ethernet: Make sure rules for cable lengths and categories are followed.
Mbps no Auto-Negotiation 10Mbps (10BASE-T, Half-Duplex) 10Mbps with Auto-Negotiation 20Mbps (10BASE-T, Full-Duplex) Note: If the attached device is set to a fixed mode (ex: Forced Full-Duplex) it will not operate as an Auto-Negotiation device. http://www.sapido.com.tw/ 10 User Manual v1.0.
3 PRODUCT SPECIFICATIONS Item Specification Key Components Chipset Realtek RTL8305N (5-port MAC with 5-port PHY) Ethernet Interfaces Standards Ethernet Port IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.
