http://www.sapido.com.tw/ 1 User Manual v1.0.
CE Statement of Conformity Our product has been tested in typical configuration by Ecom Sertech Corp and was found to comply with the essential requirement of “Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC; 93/68/EEC) http://www.sapido.com.tw/ User Manual v1.0.
Chapter 1 1.1 Introduction Hardware Features Main Chipset Realtek RTL8196E Network Processor Flash & RAM Flash:4Mbytes Serial Flash RAM:32Mbytes SDRAM Ethernet Interface WAN: 1 x 10/100 Mbps RJ45 with auto MDI/MDIX LAN: 4 x 10/100 Mbps RJ45 with auto MDI/MDIX Buttons Reboot/Reset:Press 1 second is for reboot; press 10 seconds is for reset to default configuration Power Supply Power Adapter DC5V / 0.
1.2 Product Appearance LED Indicator Status Description: LED Function Color Status Description Power System status Green On Status Reset indicator System is ready to work Green On Blinking Reset or firmware upgrade in (120ms) progress WAN x 1 WAN port activity Green On System is ready to work 100Mbps Ethernet is connected Blinking 100Mbps Ethernet Tx/Rx (30ms) activity Green On 10Mbps Ethernet is connected Blinking 10Mbps Ethernet Tx/Rx (120ms) activity http://www.sapido.com.
LAN x 4 LAN port activity Green On 100Mbps Ethernet is connected Blinking 100Mbps Ethernet Tx/Rx (30ms) activity Green On 10Mbps Ethernet is connected Blinking 10Mbps Ethernet Tx/Rx (120ms) activity http://www.sapido.com.tw/ User Manual v1.0.
Chapter 2 System and Network Setup The BRC70X is an easy to setup device for various application and environment, especially for large installs such as hotels, offices space, warehouses, hot-spots and more. To begin with BRC70X, you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. Internet Account for XDSL/Cable Modem One Ethernet (10/100mbps) network interface card.
2.3 Network setup After the network connection is built, the next step is setup the router with proper network parameters, so it can work properly in your network environment. Before you connect to the router and start configuration procedures, your computer must be able to get an IP address from the router automatically (use dynamic IP address).
1. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. 2.3.2 1. Windows XP Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”. http://www.sapido.com.tw/ User Manual v1.0.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. 2.3.3 1. Windows Vista / Windows 7 Click “Start” button (it should be located at lower-left corner of your computer), then http://www.sapido.com.tw/ User Manual v1.0.
click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”. 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ User Manual v1.0.
2.4 Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default Gateway” (In this example, the gateway IP address of router is 192.168.1.1) http://www.sapido.com.tw/ User Manual v1.0.
NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with “169.x.x.x”, please recheck network connection between your computer and router, and / or go to the beginning of this chapter, to recheck every step of network setup procedure. 2.4.1 Log into Web GUI After your computer obtained an IP address from router, please start your web browser, and input the IP address of the router in address bar, and the following message should be shown.
Input User Name and New Password, then input Confirm Password again. Chapter 3 Internet Connection This Chapter describes how to setup BRC70X to the internet. The BRC70X is delivered with the following factory default parameters. Default IP address: 192.168.1.1 Default IP subnet mask: 255.255.255.0 Web login user name: admin Web login password: admin 3.1 1. Using as a broadband router Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank. http://www.sapido.com.
2. Enter the User name and Password into the blank and then click Login. The default values for User Name and Password are admin (all in lowercase letters). Status page Download pdadd Logout 3.2 Home button menu Click Home button icon to enter MENU as below. http://www.sapido.com.tw/ User Manual v1.0.
Item Description Internet Setup There are several different method to access Internet,ADSL 、DHCP、static IP、PPTP、L2TP Status You could check WAN, LAN, Client network in status. Parental control You can use URL filter and MAC address filter schedule to limit access Internet. Firmware Upgrade This function allows you upgrade the BRC70X firmware to new version. Please note do not power off the device during the upload because it may crash the system.
DDNS You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it will reregister its domain-name-to-IP-address mapping with the DDNS service provider. Remote management This page allow you to access the GUI on WAN. Advance Setup Advance setting menu Time Zone You can maintain the system time by synchronizing with a public time server over the Internet. Factory Default You could reset the current configuration to factory default.
3.3 Internet Setup Click Internet Setup icon to enter WAN setup as below. The Internet Setup is depended on the service that you contract with the provider. The BRC70X provides five selections for the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP. Check with your ISP if you don’t know the WAN type. http://www.sapido.com.tw/ User Manual v1.0.
3.3.1 PPPoE Item Description User Name Input your user name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. 3.3.2 DHCP Item Description MAC type Select "Universal” or “Specific" http://www.sapido.com.tw/ User Manual v1.0.
3.3.3 Static IP Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address. DNS Input DNS information which is provided by your ISP 3.3.4 PPTP http://www.sapido.com.tw/ User Manual v1.0.
Item Description Address Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address. Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP.
Item Description Address Mode Select "Dynamic" or "Static" IP Address Input your IP address or domain name Gateway Input ISP Default Gateway Address. Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Chapter 4 4.1 GUI Function Setup Status You could check WAN, LAN, Client network information WAN information LAN information http://www.sapido.com.tw/ User Manual v1.0.
Client information Manage client can access internet or not 4.2 Parental Control Parental Control provide URL Filtering and MAC Filter Schedule for setup http://www.sapido.com.tw/ User Manual v1.0.
4.2.1 URL Filtering URL Filtering is used to restrict users to access specific websites in internet Item Description Enable URL Filtering Please select Enable MAC Filtering to filter MAC addresses URL Address Please enter the MAC address that needs to be filtered. Apply Click on Apply to save the setting data. Current Filter Table It will display all ports that are filtering now. Delete Selected & Delete All Click Delete Selected will delete the selected item.
4.2.2 MAC Filter Schedule When enabled, filtering will be based on the MAC address of LAN computers. Any computer with its MAC address on this list will be blocked from accessing the Internet. http://www.sapido.com.tw/ User Manual v1.0.
Item Description Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses. 4.3 Firmware Upgrade This function can upgrade the firmware of the router. There are two method for user upgrade firmware: Auto upgrade and Manual upgrade. Note: The firmware upgrade will not remove your previous settings. 4.3.1 Auto upgrade http://www.sapido.com.tw/ User Manual v1.0.
It provide auto detect new firmware from Internet, and user can select to upgrade new version or not. 4.3.2 Manual upgrade If you download firmware from website, you can upgrade firmware manual as below. 4.4 QoS The QoS can let you classify Internet application traffic by source/destination IP address and port number.
etc. Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS” to disable QoS function for the WAN port. Manual Uplink Speed Set the uplink speed by manual to assign the download or upload bandwidth by the unit of Kbps. Manual Downlink Speed Set the downlink speed by manual to assign the download or upload bandwidth by the unit of Kbps.
4.5 DoS Home: Item Description Home Check “Home” to enable DoS function for prevention. You also can check “No Prevention” to disable DoS function. Enterprise: http://www.sapido.com.tw/ User Manual v1.0.
Item Description Enterprise Check “Enterprise” to enable DoS function for prevention. You also can check “No Prevention” to disable DoS function. 4.6 IP Binding This function allows you reserve IP addresses, and assign the same IP address to the network device with the specified MAC address any time it requests an IP address. This is http://www.sapido.com.tw/ User Manual v1.0.
almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server. Item Description Enable Static DHCP Select enable to use Static DHCP function IP Address Please enter IP address to limit MAC address Please enter MAC address to limit Static DHCP List It will display all IP and MAC address you made. Delete Selected & Delete All Click Delete Selected will delete the selected item.
Item Description Enable Setting Check this option, will start the VPN Server feature. Connection Type Provide PPTP or L2TP access connection type.
This section contains configurations for the BRC70X ’s advanced functions such as: virtual server, and DMZ to provide your network under a security environment. 4.8.1 Virtual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. Item Description Enable Virtual Server Select to enable virtual server or not.
Public Port Range Enter the port number, for example 80-80. Private Port Range Enter the port number, for example 20-22. Current Port Forwarding It will display all port forwarding regulation you made. Table Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.
Item Description Enable DMZ It will enable the DMZ service if you select it. DMZ Host IP Address Please enter the specific IP address for DMZ host. 4.9 DDNS You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it will re-register its domain-name-to-IP-address mapping with the DDNS service provider. This is the way Internet users can access the router through a domain name instead of its IP address.
Please enter Domain Name, User Name/Email, and Password/Key. After entering, click on Apply Changes to save the setting, or you may click on Reset to clear all the input data. Item Description Enable/Disable DDNS Select enable to use DDNS function. Each time your IP address to WAN is changed, and the information will be updated to DDNS service provider automatically.
Item Description HTTP Connection Port Users can access GUI by this port,default is 80 Enable Web Server Access on WAN Allow user access GUI from WAN side 4.11 Time Zone Users can select time zone and synchronize the local clock on the router. Item Description Time Zone Select Please select the time zone. 4.12 Factory Default You could reset the current configuration to factory default. http://www.sapido.com.tw/ User Manual v1.0.
4.13 Reboot This function is used to reboot 4.14 Logout This page is used to logout http://www.sapido.com.tw/ User Manual v1.0.
Chapter 5 5.1 Advance Setup Internet Mode: Internet Setup Please refer Internet Setup 5.2 IP Config 5.2.1.1 PPPoE Item Description User Name Input your user name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Service Name Input the service name provided by your ISP. http://www.sapido.com.tw/ User Manual v1.0.
Connection Type Three types for select: Continues, Connect on Demand, and Manual. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration.
Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Save & Apply Click on Save to save the setting date, the Apply button for execute current configuration. 5.2.1.3 Static IP Item Description IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Gateway Input ISP Default Gateway Address, . MTU Size Maximum Transmission Unit.
5.2.1.4 PPTP Item Description Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. MTU Size Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
dictionar DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Save & Apply Click on Save to save the setting date, the Apply button for execute current configuration. 5.2.1.
DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Save & Apply Click on Save to save the setting date, the Apply button for execute current configuration. 5.2.2 LAN Use this page to set up the local IP address and subnet mask for your router.
Default Gateway Input ISP Default Gateway Address. If you don’t know, please check with your ISP. DHCP Enable or disable DHCP services. The DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer if enabled. DHCP Client Range Define the DHCP client range and then the DHCP server will assign an IP to the requesting computer from this range. The Show Client will display every assigned IP address, MAC address, and expired time.
Please enter Domain Name, User Name/Email, and Password/Key. After entering, click on Apply Changes to save the setting, or you may click on Reset to clear all the input data. Item Description Enable/Disable DDNS Select enable to use DDNS function. Each time your IP address to WAN is changed, and the information will be updated to DDNS service provider automatically.
Item Description Origin Type SLAAC、DHCPv6、IP。Please check ISP to get correct type WAN Link Type PPPoE、IP PPPoE Use IPv4 PPPoE account and password to do IPv6 connect Child Prefix Address Check ISP to get this data Static IP Check ISP to get IP address and default gateway IP address Router Name Router domain DNSv6 Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS http://www.sapido.com.tw/ User Manual v1.
5.4 NAT This section contains configurations for the BRC70X ’s advanced functions such as: virtual server, and DMZ to provide your network under a security environment. 5.4.1 DMZ The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing. When enabled, this feature opens all ports to a single station and hence renders that system exposed to intrusion from outside.
Item Description Enable Virtual Server Select to enable virtual server or not. Address Specify the IP address which receives the incoming packets. Protocol Select the protocol type. Public Port Range Enter the port number, for example 80-80. Private Port Range Enter the port number, for example 20-22. Current Port Forwarding It will display all port forwarding regulation you made. Table Delete Selected & Delete All Click Delete Selected will delete the selected item.
5.5 VPN Server: PPTP/L2TP Setup Please refer VPN server 5.6 Firewall 5.6.1 DoS Please refer DoS 5.5.2 QoS http://www.sapido.com.tw/ User Manual v1.0.
Item Description Enable QoS Check “Enable QoS” to enable QoS function for the WAN port. You also can uncheck “Enable QoS” to disable QoS function for the WAN port. Automatic uplink speed Check the Automatic uplink speed. Manual Uplink speed Input uplink bandwidth manually Automatic downlink speed Check the Automatic downlink speed.
Mode Select Guaranteed minimum bandwidth or Restricted maximum bandwidth Uplink Bandwidth Key in the bandwidth. Downlink Bandwidth Key in the bandwidth. 5.5.3 Port Filtering When enabled packets are denied access to Internet/filtered based on their port address. Item Description Enable Port Filtering Select Enable Port Filtering to filter ports. Port Range Enter the port number that needs to be filtered. Protocol Please select the protocol type of the port.
IP: 192.168.1.x Port: 80-80 5.5.4 IP Filtering When enabled, LAN clients are blocked / filtered from accessing the Internet based on their IP addresses Item Description Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. Local IP Address Please enter the IP address that needs to be filtered. Protocol Please select the protocol type of the IP address Apply Click on Apply to add the setting data Current Filter Table It will display all ports that are filtering now.
5.5.5 Mac Filter Schedule Please refer Mac Filter Schedule 5.5.6 URL Filtering Please refer URL Filtering 5.5.7 IP Binding Please refer IP Binding 5.5.8 VLAN 5.5.9 VLAN VLAN Settings Item Description Tag Add VLAN tag to packet VID Set VLAN ID(1~4096) http://www.sapido.com.tw/ User Manual v1.0.
Priority It indicates the frame priority level. Values are from 0 (best effort) to 7 (highest); 1 represents the lowest priority CIF Enable or Disable CIF http://www.sapido.com.tw/ User Manual v1.0.
5.6 System This section including Wake on LAN, Change Username/Password, Upgrade Firmware, Profiles Save, Remote Management, Time Zone, UPnP, Route Setup, VPN Passthrough, and Wan Type Auto Detection. It is easy and helpful for users making more detailed settings. 5.6.2 Wake on Lan Switch your computer ON through your LAN or the Internet . To support WOL you must have a computer with Motherboard that supports WOL, as well as a Network Controller (NIC) supporting this function.
Input User Name and New Password, then input Confirm Password again. 5.6.4 Firmware Upgrade Please refer Firmware Upgrade 5.6.5 Profiles Save Users can create a backup file that contains current router settings. This backup file can be used to restore router settings. This is especially useful in the event you need to reset the router to its default settings. 1. Save Configuration (1). Click Save (2). Please click “Save” to save the configuration to your computer. http://www.sapido.com.
(3). Select the location which you want to save file, then click Save. 2. Load configuration file (1). Tap “browse” and select configuration file then click Open http://www.sapido.com.tw/ User Manual v1.0.
(2). Click Upload to upload configuration file to BRC70X . (3). After 60 seconds, BRC70X will reboot automatically. 5.6.6 Remote Management Please refer Remote Management 5.6.7 Time Zone Users can synchronize the local clock on the router to an available NTP server (optional). To complete this setting, enable NTP client update and select the correct Time Zone. http://www.sapido.com.tw/ User Manual v1.0.
Item Description Time Zone Select Please select the time zone. Enable NTP client update Please select to enable NTP client update or not. Automatically Adjust Please select to enable Automatically Adjust Daylight Saving or not. Daylight Saving NTP Server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. Save & Apply Click on Save to save the setting date, the Apply button for execute current configuration. 5.6.
environments for simplified installation of computer components. BRC70X supports UPnP function, and can cooperate with other UPnP devices. When you activate UPnP, please click My Network Places. Users will see an Internet Gateway Device icon. By click the icon, users can enter the GUI of the router. If you do not wish to use UPnP, you can disable it. 5.6.9 Route Setup Dynamic routing is a distance-vector routing protocol, which employs the hop count as a routing metric.
Item Description Enable Dynamic Route Enable or Disable dynamic route NAT Enable or Disable NAT function Transmit There are 3 options: Receive 1. Disable:do not send any RIP packet out 2. Send RIP1 packet out 3. Send RIP2 packet out There are 3 options: 4. Disable:do not receive any RIP packet 5. Only receive RIP1 packet 6.
Item Description IPSec Pass-through Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the router, IPSec Pass-through is enabled by default. To disable IPSec Pass-through , select Disable PPTP Pass-through Point-to-Point Tunneling Protocol is the method used to enable VPN sessions to a Windows NT 4.0 or 2000 server.
6 Q&A 6.5 Installation 1. Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is installed between the XDSL line and the LAN. Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub (switch or computer). 2. Q: Why does the throughput seem slow? A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter.
6.7 IP Address 1. Q: What is the default IP address of the router for LAN port? A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0 2. Q: I don't know my WAN IP. A: There are two ways to know. Way 1: Check with your Internet Service Provider. Way 2: Check the setting screen of BRC70X. Click on Status & Log item to select Network Configuration on the Main Menu. WAN IP is shown on the WAN interface. 3.
2. Q: Why can't I connect to the router's configuration utility? A: Possible Solution 1: Make sure that your Ethernet connect properly and securely. Make sure that you've plugged in the power cord. Possible Solution 2: Make sure that your PC is using an IP address within the range of 192.168.1.2 to 192.168.1.254. Make sure that the address of the subnet mask is 255.255.255.0. If necessary, the Default Gateway data should be at 192.168.1.1.
5. Select Direct connection to the Internet and click on OK button. 6. Click on OK button. 3. Q: Web page hangs, corrupt downloads, or nothing but junk characters is being displayed on the screen. What do I need to do? A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate" feature of your NIC as a temporary measure. (Please look at the Network Control Panel, in your Ethernet Adapter's Advanced Properties tab.) 4.
address setting. As the router assign the DNS settings to the DHCP-client-enabled PC. 5. Q: BRC70X couldn’t save the setting after click on Apply button? A: BRC70X will start to run after the setting finished applying, but the setting isn’t written into memory. Here we suggest if you want to make sure the setting would be written into memory, please reboot the device via Reboot under System Management directory. 6.10 Support 1.
7 Appendices 7.5 Operating Systems 1. Microsoft:Windows 2000, XP, Vista, Windows 7. 2. Apple:Mac OS X 10.4.7, Leopard and the following related versions. 3. Linux:Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions. 7.6 Browsers 1. Internet Explorer ver. 6 and 7 and the following related versions. 2. FireFox ver. 2.0.0.11 and the following related versions.3. 3. Safari ver. 3.04 and the following related versions. 7.