User's Manual

55
66
How to Attach the “ Magic ” Hose Joint How to Attach the “ Magic ” Hose Joint
1.Loosen the four screws and slide the top of the "Magic"Hose Joint(section A in the
figure)onto the faucet. Then, securely tighten the four screws provided with the
“Magic" Hose Joint by using a screwdriver to secure the top of the joint to the faucet.
2.Remove the CAUTION label from the "Magic" Hose Joint.
Installing Water Supply Hose to the WasherInstalling Water Supply Hose to the Washer
1.Turn the nut clockwise while holding the hose.
Turn the nut counterclockwise after turning the
faucet off when you want to detach the Water
Supply Hose.
●
3.Turn the male coupler on the joint (section B in the figure) clockwise to attach it securely
to the top of the joint (section A in the figure).
The appliance is to be connected to the
water mains using new Water Supply
Hose and “Magic" Hose Joint and old
hose-sets should not be reused.
●
Joint Ring
1.While pushing the sleeve on the female coupler
(section D in the figure) of the joint down with
your fingers, connect the female coupler to the
male coupler (section C in the figure).
2.Release the sleeve, then push the Water Supply
Hose up into the “ Magic ” Hose Joint until it
clicks into place.
3.Pull the Water Supply Hose down to make sure
that it is securely attached.
How to Detach the Water Supply HoseHow to Detach the Water Supply Hose
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
Screw
CAUTION
label
About 4mm
A
B
After tightened
(About 2mm or less)
Lock Lever
Sleeve
C
D
CAUTION:
If outer diameter of faucet is larger than
calibre of the Joint Ring, loosen the four
screws and remove the Joint Ring from
the "Magic" Hose Joint.
Nut
Hose
1.Turn the faucet off.
2.Press the POWER ON/OFF button to turn the power on ,the
NORMAL button and the START/PAUSE button.
3.Press the POWER ON/OFF button to turn the power off
15 seconds later.
Please read the following procedure in order to avoid spilling water when detaching the
Water Supply Hose.
4.While pushing the lock lever and the sleeve on the female
(section D in the figure)of the joint down with your fingers,
detach the female coupler from the male coupler
(section C in the figure).
Extension of the Drain HoseExtension of the Drain Hose
When extending the external Drain Hose, please follow the below figure for the length
and height.
Extension Hose
No straight
Straight
Height
Max.15cm
Length
Max.1m
Max.3m
Set the clip part of Hose Band sideways to prevent touching the may cause
a vibration noise.
frame which
Drain Outlet
Drain Hose
Hose Band
1.Unplug the Power Cord of the washer.
2.Detach the Back Cover by loosening
screws at the back side of the washer.
Detach outer Drain Hose and gently lay
down the front side of washer on a soft
mat or cushion.
● Be careful not to open the Washer Lid and
dent the frame.
3.Detach the Cap from the left side of .frame
4.Loosen the Hose Band and pull the inner
Drain Hose out of the Drain Valve. Pull the
Hose Band out of the inner Drain Hose.
5.Remove right and left Tabs of Drain Outlet one side by another side pushing the Tabs
both in side and outside and pull the Drain Hose out toward outside of .frame
6.Let the inner Drain Hose through outside of left hole and set the protrusive guard of
inner Drain Hose to the square cutting part of , then attach the Drain Out let of
the hose until fitting the Tabs certainly to the .
frame
frame
8.Attach the Cap to the right hole.
9.Reattach Back Cover and gently set the washer upright.
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
Changing the Drain Hose DirectionChanging the Drain Hose Direction
Installing The Drain HoseInstalling The Drain Hose
Inside Hose
Hose Protector
Drain Outlet
(A Sectional Plan)
Drain Hose
Frame
Hose Band
You can change the direction from right side to left side.
Put gloves on to prevent injury of your hands when changing the Drain Hose direction.
NOTE:
NOTE:
Drain Valve
Drai n Val ve
Hose Clip
Hose Clip
Drain hole cover
Drain Hose
Drain Hose
Drain hole
Drain hole
Max.15cm
Max.1m
7.Connect the inner Drain Hose to the Drain Valve in place and fix the Hose Band as
shown below.
f you do not attach correct position marked with ,it can damage the inner Drain Hose
and cause a water leaking through the torn position.
● I
Connecting the Water Supply Hose to the “ Magic ” Hose JointConnecting the Water Supply Hose to the “ Magic ” Hose Joint
Lock
Lever
Sleeve
C
D