User's Manual

ManualsBrandsSanyo ManualsWashersSanyo Washer ASW-A85HT

ASW-A85HT

INSTRUCTION MANUAL

MICROCOMPUTER CONTROL

FULLY AUTOMATIC WASHING MACHINE

MICROCOMPUTER CONTROL

FULLY AUTOMATIC WASHING MACHINE

Before operating this washing machine, please read

these instructions carefully and completely.

Before operating this washing machine, please read

these instructions carefully and completely.

WARNING - This appliance must be earthed.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green/yellow: Earth Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this appliance may not correspond

with the coloured markings identifying the terminals in your plug, proceed as follows:

Light

The wire which is coloured green and yellow must be connected to the terminal

in the plug which is marked with the letter E or by the earth symbol

or coloured green or green and yellow.

The wire which is coloured light blue must be connected to the terminal which is

marked with the letter N or coloured white.

The wire which is coloured brown must be connected to the terminal which is marked

with the letter L or coloured black.

●

SPECIFICATIONSSPECIFICATIONS

560(W) x 535(D) x 950(H) mm

50 litres

AC Local voltage

Dimensions

Power Source

Water level (HIGH)

Power Consumption

Required Water Pressure

330 W

0.03 MPa ~ 1.0MPa

(0.3 kgf/cm ~ 10 kgf/cm )

2 2

FOR WASHER PLUG TOP 3 PIN

● If the 2-pin type of socket-outlet has a grounding terminal,

securely attach the end of the Grounding Wire to the

terminal.

● When grounding the washer, connect the grounding wire

before plugging in the Power Cord.

● If the 2-pin type of the socket-outlet has no grounding

terminal, consult your nearest dealer or securely attach

the end of Grounding Wire to a suitable grounding point,

such as a metal cold water pipe.

Never connect the Grounding Wire to a gas pipe.

● Unplug the Power Cord before disconnecting the

Grounding Wire.

For BS Standard Plug With A 13 Amp Fuse

( )

Grounding

Terminal

Grounding

Wire Of

Washer

Grounding

Wire

Grounding

Rod

FOLLOWING CAUTIONS ARE FOR WASHER USING DOUBLECORE

CORD ONLY.

SANYO Electric Co.,Ltd.SANYO Electric Co.,Ltd.

CODE NO.301-6-421S-032-40BCODE NO.301-6-421S-032-40B

Summary of content (8 pages)

PAGE 1
SPECIFICATIONS Dimensions Water level (HIGH) Power Source Power Consumption Required Water Pressure 560(W) x 535(D) x 950(H) mm 50 litres AC Local voltage 330 W 0.03 MPa ~ 1.0MPa (0.3 kgf/cm2 ~ 10 kgf/cm2 ) INSTRUCTION MANUAL WARNING - This appliance must be earthed.
PAGE 2
CONTENTS IMPORTANT SAFEGUARDS IMPORTANT SAFEGUARDS ......................................2 ！ WARNINGS ACCESSORIES .................................................3 NAME OF PARTS ...............................................3 INSTALLATION INSTRUCTIONS ............................... 4-6 NAMES AND FUNCTIONS OF CONTROL PANEL ................. 7-8 NORMAL USAGE ...............................................9 THE PREPARATION OF LAUNDRY BEFORE WASHING ............9 HOW TO USE COURSE AND PROCESS ...........
PAGE 3
ACCESSORIES Instruction manual Drain Hose Water Supply Hose “Magic" Hose Joint INSTALLATION INSTRUCTIONS Bottom Cover Screw Installing the Bottom Cover 1.Unplug the Power Cord of the washer. 2.Gently lay down the front side of washer on a soft mat or cushion.(Becareful not to dent the Frame.) 3.Insert the attached Bottom Cover into the hooks of Leg by straightly pushing until it reaches into the front hooks. 4.Fasten the Bottom Cover with a screw. 5.Gently set the washer upright.
PAGE 4
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Installing The Drain Hose 1.Loosen the four screws and slide the top of the "Magic"Hose Joint(section A in the figure)onto the faucet. Then, securely tighten the four screws provided with the “Magic" Hose Joint by using a screwdriver to secure the top of the joint to the faucet. 2.Remove the CAUTION label from the "Magic" Hose Joint. 3.
PAGE 5
NAMES AND FUNCTIONS OF CONTROL PANEL DETERGENT Indicators These are the spoon indications of the DETERGENT volume. TIMER And PRESET Indicators ● This indicator shows remained time during washing. (E.g.) Remaining time is 20 minutes Detailed operation please refer to page9. 9 ● This indicator shows when the washing is finished during presetting. (E.g.) Finish washing 2 hours later SOFT SPIN START/PAUSE Button Press the button SOFT SPIN , the light above flashes.
PAGE 6
NORMAL USAGE HOW TO USE COURSE AND PROCESS 1. Preparation 1) Make sure to fit the Drain hose. 2) Connect the water supply hose to the faucet and turn the faucet on. ● Make sure that some screws of Magic Hose is tighten. Otherwise it may cause water leak. 3) Plug the Power Cord into a socket 4) Put clothes inside 2. Press POWER ON/OFF button 3. Press START / PAUSE button ● Sensor tests the clothes weight automatically.
PAGE 7
VARIOUS FUNCTIONS HOW TO USE COURSE AND PROCESS BLANKET OPERATION STATUS FOR THE COURSE Wash Time (minutes) Rinse Type and Rinse Times Spin Time (minutes) NORMAL 5~12 Water Saver Rinse 2 times 4-5 HEAVY DUTY 7~14 Overflow Rinse 2 times 7-8 DELICATE 6 Overflow Rinse 2 times 2 BLANKET 12 Overflow Rinse 2 times 8 CUSTOM 10 Shower Rinse 1 times Water Saver Rinse 1 times 5 COURSE ● Possible the total time is not same due to different water pressure.
PAGE 8
TROUBLE SHOOTING GUIDE VARIOUS FUNCTIONS OTHERS 1.Delete the end buzzer: Press POWER ON/OFF button to switch on the power, and press START/PAUSE button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug. 2.How to drain remaining water When select this function, in 9 minutes after the working finished, the drainage valve will open to drain out the remained water inside. This will avoid water freezing inside in winter ℃ when temperature below 0℃.