L53S4/US GB 1998, 10, 27 INSTRUCTION MANUAL COLOR CCD CAMERA About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
L53S4/US GB 1998, 10, 27 SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty.
L53S4/US GB 1998, 10, 27 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. FEATURES • The optical filter is switched automatically to color image or black CONTENTS and white image according to the subject brightness. • Built-in interline transfer method 1/3" CCD, approx. 270,000 picture elements INFORMATION TO USER.............................
L53S4/US GB 1998, 10, 27 INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Pour la clientèle canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.
L53S4/US GB 1998, 10, 27 PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre).
L53S4/US GB 1998, 10, 27 PARTS NAMES 1 1 1 Lens iris output connector (4 pin) 3 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 Flange-back adjustment lever (See page 7) 2 3 Flange-back lock screw 4 4 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 2 3 5 Camera installation bracket 4 The bracket can be fixed at the top or bottom of the camera.
L53S4/US GB 1998, 10, 27 PARTS NAMES 6 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover.
L53S4/US GB 1998, 10, 27 PARTS NAMES 7 Power indicator (POWER) Comes on when the power to the camera is on. 7 9 8 8 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. F 9 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume.
L53S4/US GB 1998, 10, 27 PARTS NAMES Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 2 3 1, 4 Flange-back lock screw Fig. 1 English 7 1 2 3 Using a + screwdriver, loosen the flange-back lock screw (M2:+).
L53S4/US GB 1998, 10, 27 MOUNTING THE LENS Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. L Installation of a DC type auto-iris lens (sold separately) A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power source. This camera can receive (the A.I. LENS switch to the DC type) a CS mount type lens without the need of an adaptor.
L53S4/US GB 1998, 10, 27 MOUNTING THE LENS 4 4 DC VIDEO 1 3 Set the A.I. LENS switch in the camera setup section to the VIDEO position. Pin layout 1 2 3 4 DC type lenses Brake coil (–) Brake coil (+) Drive coil (+) Drive coil (–) VIDEO type lenses +12 V DC (50 mA max.) Not used Video output (1.
L53S4/US GB 1998, 10, 27 CONNECTIONS (A) 1 Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 2 2 Make the video signal connection between the camera and the monitor or time lapse VCR. Insert the plug of this power cord into a wall outlet. The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls.
L53S4/US GB 1998, 10, 27 SETTINGS C-BW L-L WB EI A H L INT SYNC M R Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. Set the SYNC switch to the L-L position. Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops.
L53S4/US GB 1998, 10, 27 SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. VR301 LEVEL L Backlight compensation setting Use an auto-iris lens and set the EI/BLC switch to the BLC-ON position, to engage the backlight compensation function.
L53S4/US GB 1998, 10, 27 SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/BLC switch to the EI-ON position. Set the EI/BLC switch to the OFF position. EI CAUTION: ON OFF ON BLC Note: Please refer to the specifications for dynamic range of the electronic iris. CAUTION: • The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set to the EI-ON position, do not use an auto-iris lens.
L53S4/US GB 1998, 10, 27 TROUBLESHOOTING SETTINGS C • B/W (color/black and white) switch setting This switch lets you select the timing of the automatic switching of the optical filter to color image or black and white image, according to the subject brightness. The default setting is “L”. Set the switch according to the brightness. C-BW H L (Fig.
L53S4/US GB 1998, 10, 27 SPECIFICATIONS Camera: Scanning system Interlace Image device Picture elements Effective picture elements Synchronizing system Resolution Video output level Video S/N ratio Minimum required illumination (incandescent lighting) Backlight compensation Iris function Electronic iris range Flange-back White balance Lens mount English 15 : NTSC standard TV system (525 TV lines, 30 frames/sec.
L53S4/US GB 1998, 10, 27 SPECIFICATIONS Dimensions: mm 136 126.5 1 67 3 54 11 15.4 25.2 1/4”–20 UNC 28 Features and specifications are subject to change without prior notice or obligations.
