Z6JE/US2F Owner’s Manual Table of Contents Manual del usuario 18 Manuel d’instructions 32 Tabla de contenido H DT V LC D TVHD de LCD T V H D AC L 4 Table des matières DP26640 Model No. / No. de Modelo / Nº de modèle © 2011 Sanyo Manufacturing Corporation Part No. / No.
CAUTION THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. RISK OF ELECTRIC SHOCK DO NOT OPEN! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
FCC INFORMATION __________ PC RESOLUTION CHART This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Please read before operating your HDTV! CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . 2 FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 PC RESOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 DISPOSAL PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . .3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 CONTENTS . . . . . . . . . . . . . . .
STAND ASSEMBLY ___________ NOTE: Skip these steps if you are wall mounting the TV. 1 2 Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish. Carefully insert the stand base to the bottom of the HDTV and secure the base by inserting two (2) screws as indicated in the diagram below. NOTE: Screws can be found taped to the bottom of the stand base. GETTING STARTED BATTERY INSTALLATION Install two (2) “AA” batteries in the remote control.
GETTING STARTED HDTV SIDE PANEL HDTV INPUT/OUTPUT REFERENCE HDMI 2 1 HDMI (INPUT1 or INPUT2) 1 An all digital AV interface that can accept uncompressed video signals for the very best picture possible. NOTE: A DVI conection is possible via the HDMI (DVI) INPUT1 using an appropriate adapter and connecting the audio to the Stereo Mini AUDIO jack. HDMI 1 2 2 USB Input View pictures stored in a USB flash drive. 3 3 PC Input 4 Monitor RGB (D-SUB) 4 AUDIO mini stereo jack (3.
GETTING STARTED AUDIO / VIDEO CONNECTIONS Use HDMI INPUT1 & 2 to hookup HD digital devices such as a Blu-ray player, HD Cable Box, HD Satellite Receiver or Video-game System. HDMI (DVI) INPUT1 can be used to hookup a DVI device with the use of an appropriate DVI to HDMI cable or adapter. Stereo Mini AUDIO jack needs to be hooked up to the DVI device as well Connect your digital device’s HDMI output to any of the two (2) HDMI inputs on your HDTV with the use of an HDMI cable.
REMOTE CONTROL OPERATION Turns your HDTV On or Off. Selects the video source to view. Holding down the key displays the Input List. Selects the desired Audio mode. Stereo, Mono, or SAP (when available.) Displays the Channel Information banner. Pressing it twice restores your HDTV to its factory settings. All user customized settings will be cleared. Displays the “Off” Timer.
GETTING STARTED (CONTINUED) INITIAL CHANNEL SEARCH Before proceeding, please make sure to correctly hook up your antenna or cable connection and all AV equipment to your HDTV. ON-SCREEN MENU OPERATION CHANNEL SETTING Display the On Screen menu and use the CURSOR keys to select Channel Setting. Press ENTER. Channel Search Auto – Searches the detected mode, Cable or Air. 1. PLUG IN AC POWER CORD 120V AC, 60Hz 2.
ON-SCREEN MENU OPERATION CHANNEL SETTING (CONTINUED) Digital Caption Input Setting Input Setting feature allows the removal of unused inputs from the AV input loop. Use the CURSOR keys to select an AV input. Press ENTER to disable (uncheck) or enable (check) the highlighted input. NOTE: At least one input must and will remain checked. :Skip is for reference only. Video2 Setting Captioning is textual information transmitted along with the picture and sound.
Light Sensor This feature detects ambient room light brightness and uses that reading to control the panel brightness level and picture parameters to reduce the HDTV’s power consumption. NOTE: When room lighting is dark, the panel brightness and/or the picture setting parameters such as brightness and contrast are lowered. When room lighting is bright, parameters are affected opposite. Use the CURSOR keys to select On or OFF and press ENTER.
ON-SCREEN MENU OPERATION UNDERSTANDING PIX-SHAPE PICTURE NOTE: Images on left are for a 4:3 transmission while images on right are for a 16:9 transmission. Display the On Screen menu and use the CURSOR keys to select Picture. Press ENTER. Pix1 Shows a standard definition 4:3 image in its original format, a 16:9 wide image is slightly compressed horizontally.
ON-SCREEN MENU OPERATION USB INPUT SOUND PHOTO VIEWER Display the On Screen menu and use the CURSOR keys to select Sound. Press ENTER. View pictures on your HDTV with the use of a USB mass storage device (not included.) Choose an option for your sound settings: Auto – Sound settings are linked to the current Picture option and parameters are adjusted accordingly. USB FLASH DRIVE 1 Dynamic, Mild, Standard – Predetermined sound parameters not linked with any Picture option.
PC INPUT Use your HDTV as a computer monitor by hooking up your PC or Laptop to the TV with the use of an appropriate monitor cable (not included.) Before connecting any cables, disconnect the AC power cords of both the HDTV and PC from the AC outlets. Power on the HDTV and any other peripheral equipment before powering on the computer. PC Setting Auto Adjustment – Automatically adjusts display position, dot clock and phase. Dot Clock – Adjust the Dot frequency to match your computer’s Dot frequency.
ONE-YEAR LIMITED PARTS AND LABOR WARRANTY THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN THE UNITED STATES OF AMERICA, CANADA, AND PUERTO RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
For assistance: Visit our Web site: www.sanyoctv.com or call toll free: 1-800-877-5032 We’ll be glad to Help Sanyo Manufacturing Corp. 3333 Sanyo Road, Forrest City, AR 72335 Printed in Mexico SMC, August 2011 Impreso en México SMC, agosto 2011 Imprimé aux.
