INSTRUCTION MANUAL DC-DA1160 Micro Component System REMOTE CONTROLLER RB-DA1160 1160UK(En)-cover 1 03/5/2005, 9:09 PM
PRECAUTIONS CAUTION THIS PRODUCT CONTAINS A LOW POWER LASER DEVICE. TO ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF THE PRODUCT. REFER ALL SERVICING TO QUALIFIED PERSONNEL. CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT BEAT CUT 1– 2– (4 MIN) - - The apparatus shall not be exposed to dripping or splashing. Do not use where there are extremes of temperature (below 5oC or exceeding 35oC), or where direct sunlight may strike it.
CONNECTIONS FM aerial L ch speaker R ch speaker AM loop Aerial BEAT CUT 1– 2– (4 MIN) To an AC outlet Note: - Do not connect the mains lead to an AC outlet until all connections have been made. - The system is not completely disconnected from the mains when the z/ON button is set to the z position. Unwind the aerial wires, then connect them to the AM LOOP terminals. Place the loop aerial in a position which yields the best AM reception, or attach it to a wall or other surface as shown in figure.
CONTROLS 6 5 7 8 4 2 9 10 11 1 12 3 13 14 CD player/Tuner/Generals 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Cassette deck Headphones socket (PHONES) 14. Memory button (MEMORY) 15. Function button (FUNCTION) 16. Power button ( z/ON) 17. Remote sensor (IR) 18. CD compartment lid 19. Display 20.
ADJUSTING THE CLOCK (Main unit only) Example: To set “6:30”, First, press the FUNCTION button to select “cd” or “TUNE” function, then press the z/ON button to turn the power off, only the clock display blinks. Note: If current function is “TAPE”, timer setting can’t be operated when turn the power off. 1. Press the MEMORY button. The hours display blinks. 3. Press the MEMORY button. The minutes display blinks. PM AM FM MHz kHz BASS SLEEP ST MHz kHz BASS SLEEP PM AM FM 5. Press the MEMORY button.
To start play from the desired track Select the track by using the e or f button, then press the i button. Temporarily stopping play PM AM FM MHz kHz BASS SLEEP ST REPEAT MEMORY - Press the i button. Current track number blinks on the display. To resume play, press the button again. Skip play To skip to track 6 while track 3 is playing, press the e button repeatedly until “6” appears (in the track section) on the display.
Note: “MEMORY” keeps on blinking without stopping or disappearing if you have any interruption in setting operation process, just waiting for your next setting operation step. To preset stations Up to 12 stations can be preset totally. 1. Tune in the stations to be preset as described above. 2. Press the MEMORY button on the PM main unit. AM FM BASS SLEEP 3. While “MEMORY” is blinking, press the PRESET button (or the TU PRESET button on the remote control) to select the channel to be preset.
MAINTENANCE Cleaning the tape heads Cleaning the CD player lens To ensure continued high performance, use cotton swab to clean the heads, pinch rollers and capstans of the decks after about every 10 hours of use. If the dirt persists, soak the swab in a little methylated spirit or head cleaning fluid and then clean. The lens should never be touched. If dust is on the lens, blow it off using a camera lens blower. (Consult your dealer.) 1 2 4 1. 2. 3. 4.
SPECIFICATIONS Tuner Reception frequency: FM: 87.5 ~ 108 MHz AM: 522 ~ 1611 kHz General Output power: 4 W x 2 (at 4 ohms, 10% distortion) Outputs SPEAKERS: 4 ohms PHONES: 8 ~ 32 ohms Power requirements: AC 230 V, 50 Hz Power consumption: 21 W Dimensions: 140(W) x 213(H) x 222(D) mm Weight: 2.1 kg CD player Channels: 2-channel stereo Sampling frequency: 44.1 kHz Pick-up: Optical 3-beam semiconductor laser Laser output: 0.6 mW (Continuous wave max.
GUARANTEE TO CUSTOMER Thank you for buying Sanyo. This equipment should give you many years of pleasure and faithful service but in the event that a fault occurs, the following notes for your guidance may be helpful:- Sanyo Europe Ltd.
